3.) Rigid bar BC is supported by aluminum rod (1) and bronze rod (2), as shown in the figure. If the maximum force the aluminum rod can take is 30040 N and the maximum force the bronze can take is 31190 N, determine the maximum force P that can be applied to the rigid bar BC to remain in equilibrium. Assume that L = 1100 mm and a = 500 mm. [Answer: P = 57.2 kNJ

3.) Rigid bar BC is supported by aluminum rod (1) and bronze rod (2), as shown in the figure. If the maximum force the aluminum rod can take is 30040 N and the maximum force the bronze can take is 31190 N, determine the maximum force P that can be applied to the rigid bar BC to remain in equilibrium. Assume that L = 1100 mm and a = 500 mm. [Answer: P = 57.2 kNJ

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A block of mass M = 4 kg is pulled by a force F = 100 N forming an angle of 60 degrees with themhorizontal plane with friction coefficient 0.3. Determine the work of force F, friction force and normal force.
Mechanics of Materials (Statically Indeterminate Members) A homogeneous bar with a cross-sectional area of 400 mm2 is attached to fixed supports as shown in the figure. It is subjected to lateral forces P1 = 20 kN and P2 = 50 kN. Determine the normal stress developed in segments AB and BC.
Rods BC and DE are connected to an initially horizontal rigid bar CD, while rod AB is attached to rod BC. The length, diameter, and modulus of elasticity of each rod are shown in the figure. Determine the rigid bar’s angle of tilt when the loads are applied in the system. Also, determine the Poisson’s ratio of rod DE if its diameter decreases to 0.998 in.
A rigid beam is being supported by three suspender bars made of bronze and loaded as shown in the figure. The cross-sectional area of each bar is 450 mm2. Determine the average axial stress in each bar. q = 5 t = 0
A horizontal bar of negligible mass, hinged at A in FIGURE Z and assume rigid, is supported by a bronze rod 2 m long and a steel rod 1 m long. For the steel rod, the area is 600 mm², and E = 200 GPa. For the bronze rod, the area is 300 mm², and E = 83 GPa. Which of the following most nearly gives the elastic deformation in the bronze rod? a. 0.58 mm b. 1.36 mm c. 2.56 mm d. 3.18 mm
The50-lb homogeneous bar AB is suspended from a rope that runs over a small peg at C. The bar is kept in the position shown by the horizontal force P. Determine the smallest coefficient of static friction at C for which the bar will be at rest. C
In the figure, the rigid AD bar is held vertically by two elastic rods articulated at the ends, which are horizontal at points B and C. Under the effect of a horizontal load of 120 kN of the system; a) Calculate the forces to occur in the elastic bars, b) The displacement of the top point (A) of the rigid bar. Note: (EA = 108N)
The magnitudes of the forces shown are FB = 800 lb, FC = 1000 lb and FD = 900 lb. Solve for the magnitude of force FA and the angle, alpha, that results in a vector sum of 0 on the system.
The value of EIθB, in kN m^2, the support B of the beam shown in the Figure is: Enter only in numerical heat rounded to one decimal place.
Please show complete solutions. Considering EI is constant and the value of P is 425kN, calculate the following using Conjugate beam method : A. What is the value of the reaction at point B in the real beam? B. What is the value of the reaction at Point A in the conjugate beam? C. DISPLACEMENT AT C. D. DETERMINE SA SLOPE AT B.
The rectangular cross-section beam in figure 3b is subjected to a maximum bending moment of 25,000 Nm and experiences sagging. Assuming that the centroidal axis passes through the beam section at (d/2), calculate the maximum bending stress (?max) the beam will experience. Give your answer in N/mm2 and to 2 decimal places. (show all work)
The springs BA and BC each have a stiffness of 500 N/m and an unstretched length of 3 m. Determine the horizontal force F applied to the cord which is attached to the small ring B so that the displacement of AB from thewall is d = 1.5 m.