Please show complete solutions. Considering EI is constant and the value of P is 425kN, calculate the following using Conjugate beam method : A. What is the value of the reaction at point B in the real beam? B. What is the value of the reaction at Point A in the conjugate beam? C. DISPLACEMENT AT C. D. DETERMINE SA SLOPE AT B.

Q: A column section b = 400 mm, h = 600 mm is reinforced with longitudinal bars Ast = 12-ϕ20 mm equally...

A: Given option are incorrect.

Q: Determine if the sections are Compact, Non-Compact or slender. (Use ASEP steel Handbook) Show comple...

A: The cross segments of steel shapes will quite often comprise of a gathering of slender plates. Whene...

Q: orted beam 300 mm wide, 500 mm deep and spans 5 m supports a service super imposed dead load of 7 kN...

A: Given:- b=300mm d=500mm span=5m dead load =7kN/m service live load=6kN/m f'c=21MPa fy=415MPa centroi...

Q: A simply supported beam of uniform flexure rigidity is loaded as shown in the given below. The rotat...

A: Given data, to find the rotation of the end A

Q: 1. An overhang beam carries a uniform load of 3.2 KN/m as shown in the figure. Draw the shear and mo...

A:

Q: Calculate the nominal moment strength of a reinforced concrete beam 270 mm x 490 mm if at failure th...

A: Given Data b = 270 mm, h = 490mm Assuming cover of 40mm d = 490-40 = 50mm c=600d600+fy=600×450600+42...

Q: Determine the section classification of W10x33 if Fy = 350 MPa bf = 202.18 mm tf = 11.05 mm d = 247....

A: To classify the given steel section.   Given, Steel Section: W10×33 Yield strength of steel (Fy) = 3...

Q: the maximum steel ratio if the beam is singly reinforced in negative bending with the given material...

A:

Q: In a cement plant, a bucket (B) full of crushed limestone is suspended from a travellir crane (A) wh...

A: Given, Length of cable (L) = 30 ft Speed of the crane, before sudden stop (V) = 12 ft/s   After the ...

Q: 10 KN 20 KN / m 5 KN / m A B SIMPLE STRESSES 5 KN / m 50 KN-m 5 KN / m F 3. Points C and D of the be...

A: Wood is both a typical and an authentic decision as a structure material. However, in the beyond cou...

Q: W8x40, A36 steel is used as a simply supported beam uniformly loaded over a span of 6 m.  If the top...

A: According to given data  A W8x40, A36 steel is used as a simply supported beam  uniformly loaded ove...

Q: A T-shaped built up steel beam is composed of 150 mm x 11 mm flange plate at top and a vertical web ...

A: We will find plastic modulus about equal area axis.

Q: 50 mm wide, 500 mm deep is reinforced at the bottom with 4-2e-mm-diameter bars and at the top with 2...

A: According to given data A rectangular beam 250 mm wide, 500 mm deep  reinforced at the bottom with 4...

Q: Determine the missing length and bearing in figure 3 in handwriting.

A: This question belongs to subject surveying. In this question find out unknown bearing of lines.

Q: A built up l-section is formed from plates welded together as shown in the figure. It is to be used ...

A:

Q: Determine the value of maximum load P so that the stresses in the frame illustrated will not exceed ...

A:

Q: A W12x79 of A573 Grade 60 (Fy = 415 MPa) steel is used as a compression member.  It is 6.8 m long, f...

A: Given, The Given section : W12×79 properties of the given Section are as follows:  A = 14,500 mm^2  ...

Q: Using the moment-area theorems and E = 29(103) ksi, I = 500 in4 A. Reactions at A B. Determine the m...

A:

Q: .In the given soil profile detemine the 6'of the points A,B.C and D. Show the v ariations in a diagr...

A: Given data in question  Void ratios Depths of various soil layers Porosity Specific gravity  Water t...

Q: A rectangular footing 2.1 m x 3.6 m x 0.35 m thick supports a 300 mm square column at its center. Co...

A:

Q: steel strain (in 5 decimal places) compatible with concrete strain of 0.003 for a singly reinforced ...

A: According to given data  concrete strain of 0.003   singly reinforced beam 300 mm wide, 680 mm deep ...

Q: Concrete is the second most used material on earth next to water and it is approximately 80% aggrega...

A: Concrete is a composite material with a combination of cement, fine aggregate, coarse aggregate, adm...

Q: An axially loaded tied column must sustain the following service loads: Total Dead Load    = 1,000 ...

A:

Q: Determine the equivalent length of 15000m on a graphic scale of a map whose representative fraction ...

A:

Q: A symmetric I-shaped built up steel beam is composed of 220 mm x 17 mm flange plates at top and bott...

A: Hello dear, please see the attached solution, thanks

Q: Solve for the unknown values in table 1 and 2 in handwriting

A:

Q: A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars a...

A: Given, Width of beam=250 mm Depth of beam=500 mm Bottom bars =4-20 mm diameter Top bars=2-16 mm diam...

Q: W12x79 of A573 Grade 60 (Fy = 415 MPa) steel is used as a compression member.  It is 6.6 m long, fix...

A:

Q: Determine the tensile steel strain (in 5 decimal places) compatible with concrete strain of 0.003 fo...

A:

Q: As shown in the figure below, determine the internal loadings at points A,B and. Consider the unifor...

A:

Q: A 500-mm-diameter, non-slender, spiral column is symmetrically reinforced with six 25 mm vertical ba...

A: Diameter of column=500mm Diameter of reinforcement=25mm

Q: According to the provisions of NSCP 2015, in flexural reinforced concrete members a compression cont...

A:

Q: An A36 tension plate is 15 mm thick is given below. Bolts are 16 mm. Given that s = 90 mm and g = 70...

A:

Q: The 20mmØ bottom bars in the figure are epoxy coated. Assuming normal weight concrete, fy= 420 MPa, ...

A:

Q: Calculate the tensile steel stress of 5-16-mm-dia rebars in a concrete beam 220 mm by 480 mm at ulti...

A:

Q: Slider block A moves to the left with a constant velocity of 6 m/s. Determine the velocity of block ...

A:

Q: A simply supported beam 300 mm wide, 500 mm deep and spans 5.7 m supports a service super imposed de...

A:

Q: In its natural state, a moist soil has a volume of 0.00935 m3and weighs 178 N. The oven dry weight o...

A:

Q: Determine the tensile steel strain (in 5 decimal places) compatible with concrete strain of 0.003 fo...

A: To find Tensile steel strain

Q: i. Versine, V ii. Long Chord, C ii. Length of the curve, LC

A: The mid-ordinate or versine is the maximum distance between the long chord and the curve. The maximu...

Q: flow through each pipe. Ioss and 15.27 Two reservoirs having a difference of 40 ft in water elevatio...

A:

Q: Note: HP12X53 Ag=15.5 in^2 rx = 5.04 in ry = 2.86 in 16' HP 12 × 53 A572 Grade 50

A:

Q: : A cable having span of 100 m, dip "h" = 10 m is subjected to a rise is temp. of 10°C. The cable su...

A:

Q: Given the loaded frame below, which is the bending moment diagram of member AB.

A:

Q: Q6. If the known benchmark elevation of a proposed building in downtown Nashville is 597.2 ft. When ...

A:

Q: . Determine the tensile steel strain (in 5 decimal places) compatible with concrete strain of 0.003 ...

A: We have to determine the tensile steel strain (in 5 decimal places) compatible with concrete strain ...

Q: Use the suggested ACTUAL fixity factor recommended by the AISC k =0.8. What is rhe Demand capacity r...

A:

Q: A 6.58° horizontal curve has a central angle of 48.4°. If the station of PT is at 25+198, determine ...

A:

Q: An axially loaded tied column must sustain the following service loads: Total Dead Load    = 1,000 ...

A:

Q: SIMPLE STRESSES 340 mm 1. Two plates are connected by bolts as shown in the figure. Compute the bear...

A: To determine the bearing stress in each bolt.   Given, Diameter of each bolt (d) = 20 mm Magnitude o...

Matrix Algebra for Structural analysis

Structural analysis is a process in which the effects of different loads and internal forces, acting on structures and their elements are determined. This method of analysis is effective in detecting the failure loads of the structural elements and the design can be altered before commencing the construction process, which ensures proper strength and safety of the structures.