3. The coordinates of two points on a given compression curve are as follows: e₁ = 1.82 e₂ = 1.54 P₁ =200 kPa P2=400 kPa a. Compute the coefficient of compressibility. b. Compute the coefficient of volume compressibility for the pressure stated above. c. Given the coefficient of consolidation Cv = 0.003 cm²/sec, determine the hydraulic conductivity (k) in cm/sec. corresponding to the average void ratio.

3. The coordinates of two points on a given compression curve are as follows: e₁ = 1.82 e₂ = 1.54 P₁ =200 kPa P2=400 kPa a. Compute the coefficient of compressibility. b. Compute the coefficient of volume compressibility for the pressure stated above. c. Given the coefficient of consolidation Cv = 0.003 cm²/sec, determine the hydraulic conductivity (k) in cm/sec. corresponding to the average void ratio.

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter15: Braced Cuts

Section: Chapter Questions

Problem 15.5P

See similar textbooks

Similar questions

Hi, please calculate and plot the distrbution of passive pressure in front of the wall and active pressure behind the wall In Soil 1: cohesion, c =0 angle phi = 38 degrees bulk unit weight, Y = 18kN/m3 For Soil 2: cohesion, c =0 angle phi = 28 degrees bulk unit weight, Y(sat) = 20kN/m3
A strata of normally consolidated clay of thickness 10 ft is drained on one side only. It has hydraulic conductivity of h = 1.863 x 10~ 8 in/sec and a coefficient of volume compressibility ra v = 8.6 x 10" 4 in 2 /lb. Determine the ultimate value of the compression of the stratum by assuming a uniformly distributed load of 5250 lb/ft 2 and also determine the time required for 20 percent and 80 percent consolidation.
5. A thick layer of stiff saturated clay is underlain by a layer of sand under artesian pressure. A deep cut is made in the clay layer as shown in the attached figure. Determine: [2] a. The total stress at point A. b. The factor of safety against heaving at point A, if the effective stress is 12% of the total stress.
Problem # 4. A 2m. clay layer has values of e = 0.92, Gs = 2.72 and liquid limit of 40%. Above the clay is a 3m thick layer of sand with e =0.50 and Gs = 2.62. The water table is located 1.6 m below the ground. If a 3m thick backfill is placed on the ground surface having a unit weight of 17.3 kN/m^3, determine the following: a. Compression index of clay.b. Effective pressure at the midpoint of clay.c. Primary settlement for normally consolidated clay.
The soil profile at the site consists of a 5.0 m sand layer underlain by 13 m of clay layer. The groundwater table is at a depth of 2.8 m below the ground surface. The sand has a unit weight of 19 kN/m3 above the groundwater table and 20 kN/m³ below the ground water table. Meanwhile, the saturated unit weight of clay is 15.7 kN/m3. At a depth of 11m from the ground lever, calculate the Total Pressure, Porewater Pressure, and the Effective Pressure (in kPa).
A masonry dam has a coefficient of permeability in the vertical and horizontal directions of Kz=4m/day and Kx=5m/day, respectively. The difference in the head is 18m and the distance between the base of the dam and the downstream water surface is 18m. Assume z=35m and width of dam = 40m. a. Determine the seepage flow (m3/day) b Determine the uplift pressure (kpa) at A. c. Determine the uplift force (x10^3 kN) acting in the dam. Assume that the uplift pressure under the dam varies uniformly.
The plan of a flexible circular loaded area is resisting the uniformly distributed load(q), 835 kN/m2 with the radius of 5.7 m. Illustrate and calculate the increase in thevertical stress (Δσ) at a depth of z = 7.2 m below point A which is immediately belowthe center.
If there is a layer of sand (lower layer) under artesian pressure (causes upward flow), calculate the excavation height H so that a negative effective stress is not generated at point A and therefore the heaving of the soil at that point. Use a unit weight of water w of 62.43 lb/ft3. Note: In this example we make a similarity with the permeameter with upward flow, therefore, H1=0 since from the bottom of the excavation (Na) upwards it remains dry (pumping is done), H2= 20ft-H, h=12ft-H2.
A retaining wall 8 m high supports a cohesionless soil having a dry density of 1600 kg/m^3, angle of shearing resistance is 33 degrees and void ratio of 0.68. The surface of the soil is horizontal and level with top of the wall. Neglect wall friction and use Rankine’s formula for active pressure of a cohesionless soil. Determine the value of earth thrust on the wall per meter length if the soil is dry. a. 121 kN b. 186 kN c. 148 kN d. 137 kN determine the value of earth thrust on the wall if water level is 3.5 m below the surface. a. 230 kN b. 250 kN c. 180 kN d. 210 kN find the height above the base of the wall where the thrust acts during the water logged condition. a. 3.50 m b. 2.67 m c. 1.75 m d. 2.25 m
A 4-meter clay layer (e = 0.89, Gs = 2.69, Cc = 0.349) is overlain with 4-meter-thick sand layer (e = 0.83, Gs = 2.51). The water table is at the interface of the sand and clay layer. If a 2-meter-thick land fill (Y = 17.36 kN/m^3) is placed over the existing ground surface, compute the consolidation settlement (in mm) of the clay layer. Hint: use the land fill's resulting pressure on the ground surface as the stress increase.
For a cutoff wall shown in Figure 4a. Establish the flow nets (i.e. flow and equipotential lines) following all the rules (Drawdirectly on Figure 4).b. Deten:nine the quantity of seepage (m3/s perm) (coefficient of permeability, k = 2.0 x10·5 mis).c. Calculate the effective stress at point A (back of the piling) (Yu.t = 20 kNlm\d. Estimate the stability of the cutoff wall using lhe Factor of Safety, FS.
A 3-meter clay layer (e = 0.97, Gs = 2.54, Cc = 0.305) is overlain with 2-meter-thick sand layer (e = 0.87, G = 2.57). The water table is at the interface of the sand and clay layer. If a 2-meter-thick land fill (γ = 17.69 kN/m3) is placed over the existing ground surface, compute the consolidation settlement (in mm.) of the clay layer. Hint: Use the land fill's resulting pressure on the ground surface as the stress increase. Round off to two decimal places.