3. The parameters of the transistor in Figure 3 are ß= 100 and VA 100 V. (a) Find the de voltages at the base and emitter terminals. (b) Find Re such that VCEQ = 3.5 V. (c) Assuming Cc and CE act as short circuits, determine the small-signal voltage gain Av = vo / Vs. (d) Repeat part (c) if a 500 2 source resistor is in series with the v, signal source. V+ = +5 V Rc Figure 3 Rs = 100 2 www V₂ Cc RB = 10 ΚΩ 1 = 0.35 mA O V=-5 V OVO CE

3. The parameters of the transistor in Figure 3 are ß= 100 and VA 100 V. (a) Find the de voltages at the base and emitter terminals. (b) Find Re such that VCEQ = 3.5 V. (c) Assuming Cc and CE act as short circuits, determine the small-signal voltage gain Av = vo / Vs. (d) Repeat part (c) if a 500 2 source resistor is in series with the v, signal source. V+ = +5 V Rc Figure 3 Rs = 100 2 www V₂ Cc RB = 10 ΚΩ 1 = 0.35 mA O V=-5 V OVO CE

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Which of the following is the basic feature of the emitter-connected amplifier circuit? I. It has voltage gain II. It has current gain III. There is a 180 degree phase difference between the input signal and the output signal
Since Vcc = 12 V, Vin = 690 mV, RB = 780 kΩ, RC1 = 27.9 Ω, RC2 = 25.4 Ω, RE = 470 Ω, RL = 47 Ω and β1 = β2 = 100 in the circuit in the figure Find the current (IL) flowing through RL? NOTE-1: VBE1 = VBE2 = 0.7 V will be taken. NOTE-2: Output impedances of transistors (r0) will be neglected.
See attached picture: Which two transistors are p-type and which two are n-type? Refer to the transistors by their labels (a, b, c, or d). Also, which transistors (a, b, c, or d) are “ON” when: A) Input A = 0, Input B = 0 B) Input A = 1, Input B = 0 C) Input A = 0, Input B = 1 D) Input A = 1, Input B = 1
Vi=20mV , Vcc=15V ,β=110 , r0=30kΩ , Rc=4.7kΩ , RF1=100kΩ , RF2=47kΩ AC source internal resistance Rs = 1.34kΩ , load RL=9,1kΩ output voltage V0 =? Note : Output impedance of transistor r0 must be taken into account in calculations
‏For the common - emitter amplifier shown in Figure Q3 below , solve the circuit for the following : (i) Collector current Ico ( ii ) Voltage gains Ay and Avoc ( iii ) Input impedance .
For the given Common Emitter NPN Amplifier, the transistor made of Germanium diodes, βDC=80,VCC = 16 volts, R1= 62 KΩ, R2= 9.1 KΩ, RC= 3.9 KΩ, RE= 0.68 KΩ. a) Name the type of biasing used in the above circuit? b) Find VE? c) Find VCE? d) Find VC? e) What is the name of the capacitors C1, C3and C2?
The magnitudes of a pnp transistor’s emitter andbase currents are 6 and 0.1 mA, respectively. Themagnitudes of the voltages across the emitter-base andcollector-base junctions are 0.65 and 7.3 V. Finda. VCE.b. IC.c. The total power dissipated in the transistor, definedhere as P = VCEIC + VBE IB.
Knowing the equation of collector current IC for the transistor amplifier circuit, please calculate the current and voltage stabilization factors. Rc=2000ohm Re=500ohm Rb=500ohm Rb=1000ohm Beta0=200
From the transistor collector characteristic shown, determine βac for an operating point of IB = 150μA and VCE = 6V. A. 265B. 253 C. 240 D. 232
Instruction/s: 1. Draw, Illustrate and label your schematic diagram before solving the problem. 4.) Given a Voltage -divider biased transistor circuit .Assume Beta DC is 100, ,Voltage at Base-emitter junction is 0.7v ,voltage at common collector is +15v, resistor RB1 is 10k ohms, resistor RB2 is 6k ohms, collector resistor is 1.5k ohms ,emitter resistor is 560 ohms. Determine base current ,collector current and voltage collector-emitter junction. These might help as a guide in answering the problem..
Design a common emitter amplifier for a Vout of+-6.3V. Vcc is set to 9V. At x=1, Av=12.6 V/V and the dynamic range from 6.3V to -6.3V. Rout must be less than 100 ohms and Rin must be higher than 100 kohms
Q 3 emitter voltage divider-biased circuit. Given that RB = 25kΩ, R2 = 2.5kΩ, RC = 5kΩ, RE = 1kΩ, VCC = 22V, VBE = 0.7V, C1 = C2 = 10µF and β= 90, (i) the Thevenin equivalent circuit. (ii) the base current, IBQ, the collector current, ICQ and the collector-emitter voltage, VCEQ. (iii) the collector voltage, VC, the emitter voltage, VE, and the base voltage, VB. (b) If the circuit in Figure Q3 has ro = 40kΩ, (i) Draw the AC equivalent circuit using re model. Label all currents, voltages, resistors and directions correctly. (ii) Analyze the circuit to determine re, input impedance, Zi, output impedance, Zo and voltage gain, Av.