3. The steel framework is used to support the 100-mm reinforced stone concrete slab that carries a uniform live loading of 24 kPa. Sketch the loading that acts along members BE and FED assuming simple supports. Set b = 3.0 m and a = 1.8 m. Use alternate method for live load reduction. Solve in accordance to NSCP 2015. b [x] E 4. Solve again Problem No.3. Set b = 3.6 m and a = 1.2 m. Use alternate method for live load reduction. Solve in accordance to NSCP 2015.

3. The steel framework is used to support the 100-mm reinforced stone concrete slab that carries a uniform live loading of 24 kPa. Sketch the loading that acts along members BE and FED assuming simple supports. Set b = 3.0 m and a = 1.8 m. Use alternate method for live load reduction. Solve in accordance to NSCP 2015. b [x] E 4. Solve again Problem No.3. Set b = 3.6 m and a = 1.2 m. Use alternate method for live load reduction. Solve in accordance to NSCP 2015.

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter7: Settlement Of Shallow Foundations

Section: Chapter Questions

Problem 7.2P: A planned flexible load area (see Figure P7.2) is to be 3 m × 4.6 m and carries a uniformly...

See similar textbooks

Similar questions

A planned flexible load area (see Figure P7.2) is to be 3 m × 4.6 m and carries a uniformly distributed load of 180 kN/m2. Estimate the elastic settlement below the center of the loaded area. Assume that Df = 2 m and H = . Use Eq. (7.4).
A raft of size 4 m-square carries a load of 400 kN/m2. Determine the vertical stress incrementat a point 5 m below the centre of the loaded area using Boussinesq’s theory. Compare theresult with that obtained by the equivalent point load method and with that obtained bydividing the area into four equal parts the load from each of which is assumed to act throughits centre
A square footing ( 3'×3') shown in figure. Determine the allowable resisting moment (M), if the dead load is 350 kips and live load is 450 kips and F.S = 3. Using Meyerhof Equation.
A rectangular “Apitong” beam 50mm x 300mm is used as a simply supported beam 3.2m long. Determine the largest uniformly distributed load, which can be, applied over the central half of the beam if the flexural stress is limited to go 12MPa?
The channel section carries a uniformly distributed load totaling 6W and two concentrated loads of magnitude W. Determine the (a) location of the neutral axis from the bottom, (b) the moment of inertia about that axis, (c) the maximum allowable value for W if the working stress are 4.0 MPa in tension, 8.0 MPa in compression, and 2.4 MPa in shear.
A simply supported rectangular beam of length 6.45m has a width of 437.5 and an effective depth of 692.5. The beam is to be reinforced using 12 mm bars. The beam supports service dead loads of 31 kN/m and 39.5kN/m., respectively. the fc' is 28MPa, fy is 420MPa and Wu is 89.9kN/m. 1. what is the ultimate moment capacity of the beam? 2. what is the height of the equivalent stress block? 3. Determine the number of bars required for this beam
Two columns A and B are situated 6 m apart. Colum A transfers a load of 500 kN and column B, a load of 250 kN. Determine the resultant vertical stress on a horizontal plane 20 m below the ground surface below point A. a.12.4 kPa b.232.49 kPa c.29.9 kPa d.59.8 kPa
The safe stress , for a hollow steel column which carries an axial load of 2.1 x 10^3 kN is 25 MN/m^2. If the external diameter of the column is 30cm, determine the internal diameter.
1. Determine the critical bucklng stress of the column in MPa. a.120.68 b.116.10 c.101.32 d.108.57 2. Determine the nominal axial load that the column can carry in kN/ a.1448.16 b.1393.20 c.1221.84 d.1302.84 3. Determine the service live load that can be applied in the column kN. a.119.53 b.597.64 c.143.44 d.956.22 Answer:101.82, 1221.84,597.64
A building floor plan having two reinforced concrete slabs of 200 mm thick and density of 24 kN/m3 are supported by beams as shown in figure Q1. The slabs of floor are subjected to impose load 6 kN/m2, Find the total design load on beam B1.
The cross section of a proposed concrete retaining wall is shown in Figure 4. The unit weight of the concrete being 24kN/m3. The soil carries a uniformly distributed load of 40kN/m2 at the top. Given c=0, f=32°, gsoil=17.5kN/m3 and µ=0.5. From the data: Check the stability of the retaining wall against sliding and overturning Determine the maximum and minimum pressure under the retaining wall.
The interior wall of a building is made from 51 × 102 mm wood studs, plastered on two sides. If the wall is 4 m high, determine the load in kN/m of length of wall that it exerts on the floor.