Given: H₁ = 1.10 m, H₂ = 2.20 m, h = 1.30 m, void ratio of sand e = 0.62, specific gravity of soil solids Gs = 2.72, area of the tank = 0.5 m², and hydraulic conductivity of sand = 0.1 cm/sec. a. What is the effective stress at C if z = 1.23 m? b. What should be the value of h to cause boiling? Inflow Outflow H₂ Valve (open)

Given: H₁ = 1.10 m, H₂ = 2.20 m, h = 1.30 m, void ratio of sand e = 0.62, specific gravity of soil solids Gs = 2.72, area of the tank = 0.5 m², and hydraulic conductivity of sand = 0.1 cm/sec. a. What is the effective stress at C if z = 1.23 m? b. What should be the value of h to cause boiling? Inflow Outflow H₂ Valve (open)

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter9: In Situ Stresses

Section: Chapter Questions

Problem 9.12P

See similar textbooks

Similar questions

A sand has Gs = 2.66. Calculate the hydraulic gradient that will cause boiling for e = 0.35, 0.45, 0.55, 0.7, and 0.8.
From the figure shown, H1 = 0.60, H2 = 0.90 m. and h = 0.45 m. The sad has a saturated unit weight of 18.65 kN/m3 . Hydraulic conductivity of sand K = 0.12 cm/sec. If the cross sectional area of tank = 0.46 m2 , determine the following: 1. Total stress and Effective stress at C. 2. Pore water pressure at C. 3. Rate of upward seepage of water in liters/sec.
Given that: • Hydraulic gradient = 0.43 • unit weight of the saturated soil layer = 19.80Kn/m³ • rate and direction of seepage = 4.29 x 10^-4 m³/s (upward) • moisture content of the fully saturated soil layer = 24.25% Answer the ff: a) What would be the critical value of h to cause boiling b) If the value of h= 1.5 m boiling will? and If the value of h= 4.0 m boiling will? c) The total stress at point B d) The effective stress at point B e) The neutral stress at point B
11. Consider the downward flow of water through a layer of sand in the tank shown. (see picture below) Void ratio of the soil = 0.52 Specific Gravity = 2.70 Compute the value of h1. (Answer: 0.436) Compute the effective stress at A. (Answer: 17.44 kPa) Compute the effective stress at B. (Answer: 31.98 kPa) Compute the seepage force per unit volume. (Answer: 3.57 kN/m3)
For the soil profile show in figure calculate the total vertical stress pure water pressure and effective vertical stress at depth of 0 m 1.2m 2.5m and 5m and 8m.
Consider the upward flow of water through a layer of sand in a tank as shown in Figure below. For the sand, the following are given: void ratio (e) = 0.40 and specific gravity of solids = 2.65. i. Calculate the total stress, pore water pressure, and effective stress at points A and B. ii. What is the upward seepage force per unit volume of soil?
A layer of soil has the following properties: void ratio = 0.44, effective diameter = 12 μm, capillary constant C = 0.18 cm2 . Groundwater table is 10 m below the ground surface. (a) Find the height of capillary rise in the soil in mm. (b) What is the effective stress in kPa at 7 m depth if unit weight of solids is 25.55 kN/m3 and soil above the capillary zone is 40 % saturated? (c) What is the effective stress in kPa at 14 m depth?
The figure shows a layer of granular soil in a tank with an upward seepage by applying water through the valve at the bottom of the tank. The loss of head caused by upward seepage between the levels of A and B is 0.71m. The void ratio of the soil is 0.511 ,its specific gravity is 2.719, h1=0.99m, h2=2.06m, h3=2.91m. 1. Compute the effective stress at C in kPa. 2. .Compute the critical hydraulic gradient. X IN FIGURE IS 1 = 0.71m
A dense silt has the following properties: Void ratio (e) = 0.40, SpecificGravity (Gs) = 2.70, Effective diameter d10 = 1x10^-6 m, Capillary constant (C) = 0.20 cm^2. Free ground water level is 8.0 m below the ground surface. a. Find the height of capillary rise in the silt. b. Find the vertical effective stress in kPa at 5m depth. Assume that the soil abovethe capillary zone or capillary action rise to be dry soil and the soil within thecapillary action be partially saturated (degree of saturation, S) at 50%. c. Find the vertical effective stress at 10m depth. Assume that the soil above thecapillary zone or capillary action rise to be dry soil and the soil within the capillaryaction be partially saturated (degree of saturation, S) at 50%.
Consider the upward flow of water through a layer of sand in a tank as shown in Figure QI(c), For the sand, the following are given: void ratio (e) = 0.52 and specific gravity of solid = 2.67. Determine: (i) Total stress, pore water pressure and effective stress at points A and B (ii) The upward seepage force per unit volume of soil.
The weight density of a mud is given by ? = 10 + 0.5ℎ, where ? is in kN/m3 and h is in meters. Determine the pressure, in kPa, at a depth of 5m.
A soil profile consisting of three layers is shown in Table and Figure below i. Calculate the values of σ, u and σʹ at points A, B, C, and D. ii. Calculate the effective stress at c when water table drops by 1 m (consider γb= 15.5 for layer 2). iii. Calculate the effective stress at c when water table rises by 1 m above layer 1 due to flooding. (consider γsat= 16.5 for layer 1). Layer no. Thickness Soil parameters 1 H1 = 3.5 m γd = 15.5 kN/m3 2 H2 = 2.5 m γsat = 18 kN/m3 3 H3 = 3 m γsat = 18.5 kN/m3