Which option is not correct 3. Which of the following statements IS NOT CORRECT? *for two motors with equal output power, smaller are the dimensions of the motor with higher magnetic fluxdensity and current densityfor two motors with equal output power, bigger are the dimensions of the motor with higher speedthe output power, speed and cooling system of the rotating electrical machine influence on theelectromagnetic loadings we choose when design the machine

Motor: It is an electromechanical device. this takes the electrical input and converts this power…

3. Which of the following statements IS NOT CORRECT ? * for two motors with equal output power, smaller are the dimensions of the motor with higher magnetic flux density and current density O for two motors with equal output power, bigger are the dimensions of the motor with higher speed the output power, speed and cooling system of the rotating electrical machine influence on the electromagnetic loadings we choose when design the machine

3. Which of the following statements IS NOT CORRECT ? * for two motors with equal output power, smaller are the dimensions of the motor with higher magnetic flux density and current density O for two motors with equal output power, bigger are the dimensions of the motor with higher speed the output power, speed and cooling system of the rotating electrical machine influence on the electromagnetic loadings we choose when design the machine

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter17: Commercial And Industrial Air-conditioning Control Systems

Section: Chapter Questions

Problem 4RQ

See similar textbooks

Similar questions

A 50-KW, 220V, 50 Hz, squirrel-cage three-phase induction motor is needed to rotate a mine conveyor belt drive. The motor starts sometimes under load, but most of the time is needed to run at rated speed and slip of 3.5%. Propose an appropriate design of this drive motor in order to suit the application. Motivate and then illustrate your design with suitable drawings and speed (slip)-torque graphs.
(TRUE OR FALSE) - Lenz’s law rule is used to determine the direction of rotation of dcmachines. - Compound dc motor at no-load it regulates highest speed. - The direction of this force is perpendicular to both the wire and themagnetic field in DC motor.
A dc shunt motor after running for several hours on constant mains of 400V takes a field current of 1,6A. If the temperature rise is known to be 40°C, what value of extra circuit resistance is required to adjust the field current to 1,6A when starting from cold at 20°C? Temperature coefficient of the motor’s armature material is 0,0043C at 20°C.
A DC motor is initially at rest and is then connected to a 12V battery. The motor has aresistance of 2 Ohms and an inductance of 0.5 Henrys. The motor has a torque constant of0.1 Nm/A and a back EMF constant of 0.1 V/(rad/s). Determine the current through themotor as a function of time, and the time it takes for the motor to reach 90% of its finalsteady-state speed.
A d.c. shunt machine has armature and field resistances of 0.025 Ω and 80 Ω respectively. When connected to constant 400-V bus-bars and driven as a generator at 450 r.p.m., it delivers 120 kW. Calculate its speed when running as a motor and absorbing 120 kW from the same bus-bars
Q4 A permanent magnet dc motor is connected to a150 V dc supply and spins at 1,500rpm when no mechanical load is applied. The armature resistance (Ra) has previously been measured as 0.5Ω. (a) Sketch the equivalent circuit of this DC motor. (b) Calculate Kaϕ for this motor.
A permanent-magnet automotive fan motor draws 20 A from a 12-V source when the rotor is locked (i.e., held motionless). a. Find the armature resistance. b. Find the maximum developed power that this motor can produce when operated from a 12-V source. c. Repeat part (b) for operation at 10 V (this represents a nearly dead battery) and at 14 V (this is the terminal voltage during charging of the battery after the engine is started).
A series motor with unsaturated magnetic circuit and negligible resistance, when running at a certain speed on a given load, takes 50 Amp at 500 Volts. If the load torque varies as the cube of the speed. Find the resistance necessary to reduce the speed by 20%
Choose the right answer from the following: 1-Stepper motors used in industry due to: a- Their availability and low cost. b-Their easy control arrangement. c-Their accuracy in position control. 2-The stepper motor used in robotics due to: a. Its reduced weight, volume and losses. b.Its ability to reach certain angle precisely c. Its ability to stop without breaking arrangements. 3-The Permanent Magnet Motor (PMM) supplied by: a- DC voltage. b- AC voltage. c-AC/DC voltage. 4- Are the iron losses in the core of a synchronous motor: a- The same as that of the induction motor rotor of the same rating and speed? b-Less than that of the induction motor rotor of the same rating and speed? c-Greater than that of the induction motor rotor of the same rating and speed? 5- Are the iron losses in the core of a synchronous motor rotor: a-Greater than that of the synchronous motor rotor of lower rating and speed? b- Lower than that of the synchronous motor rotor of lower rating and speed? c- Equal…
what is the best suitable motor for below application? In a belt conveyor system used to transport bulk solids, the belt speed is required to be maintained constant at the set speed all the time irrespective of the bulk solids content on the belt. Hence, the electric motor used in this system should be able to operate more or less at a constant speed in a wide range of different torque values.
A 32kW, 250V DC shunt machine has an armature and field resistances of 0.05Ω and 120Ω respectively. Determine the total armature power developed when working as generator delivering 32kW output.
2) the armature windings of a 12-pole DC machine are composed of 72 coils with 10 windings, and the windings are 5the layered wave is yellowish. The Rotor speed is 1000 rpm and the flux value per pole is 25mWb.Resistance of Armature windings, commutation windings and compensation windings is 70mΩ, 10mΩ and5mω. (d) calculate the voltage value induced in the machine. (e) DC machine as a foreign (external) excitation generator with a rated current of 100A at full loadif it is started, what is the terminal voltage value? Calculate. (Enter the formulas that you use for calculations and enter the names of the corresponding parameters.)