3.2 Two forces and a couple are applied to the beam in an attempt to lift it. Replace this force system by an equivalent force-couple system with the force acting at (a) point A; and (b) point B. 2m 36 kN 3m 20 kN 2m -B 94 kN-m x

3.2 Two forces and a couple are applied to the beam in an attempt to lift it. Replace this force system by an equivalent force-couple system with the force acting at (a) point A; and (b) point B. 2m 36 kN 3m 20 kN 2m -B 94 kN-m x

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter3: Resultants Of Force Systems

Section: Chapter Questions

Problem 3.4P: The four forces shown act on the rollers of an in-line skate. Determine the equivalent force-couple...

See similar textbooks

Related questions

Q: 90. A pump propels a water flow of 222 l/s through the given horizontal piping system to a closed…

A: Given:Water flow rate, Q=222 L/s=222*10-3 m3/s=0.222 m3/sLiquid level in the closed tank, zC=3…

Q: 5. How we will measure the flow rate? Explain any one-flow rate-measuring instrument.

Q: the irreversibility (in W) due to heat

A: Given data, One side of the wall,Tin=400 KOther side at,Tout=300 KRate of heat transfer, Q=1000…

Q: A large iceberg floating in sea water is of cubical shape and its specific gravity is 0.9 if a 20 cm…

A: Given data: SGCu=0.9x=20 cmSGw=1.025 Need to determine the volume of the iceberg.

Q: m.i Water at m = 0.02 kg/s and T = 20°C enters an annular region formed by an inner tube of diameter…

A: Given data: m=0.02 kg/s˙Di=25 mmTm,i=20°CDo=100 mmTs,i=100°CTm,o=75°C Need to determine the length…

Q: In steady state, the heat transfer coefficient "k" is L=0.5 m Left face temperature of infinitely…

A: Given data as per questionT=250°Ch=40W/mKL=0.5mk=10W/mkqu=5×104W/m3

Q: 4) For the beam shown with a rectangular cross-section: a) Draw the shear and moment diagrams (F =…

Q: The volume of the cylindrical body is 0.04 m³ and its total mass is M ... Kg. The base radius of the…

Q: Determine the work done Force applied=0.033 N Displacement=0.1 m

A: Given data : Displacement=d Force applied=F Required : Work done

Q: In an ideal Brayton cycle, atmospheric air (ratio of specific heats, c/c, = 1.4, specific heat at…

Q: Problem 2. For the Plane frame shown in figure, determine the axial force in cord (DE) and the…

Q: How does a portable thermoelectric charger work? and how can charge phones using a USB charger?

A: Portable thermoelectric charger This is also known as TEG module-based charging, where heat is…

Q: Following the theorem of corresponding states, for compressibility factor Z > 1.0 (hard fluid) The…

A: given = multiple choice question

Q: The 6-kg uniform rod AC is attached to springs of constant k = 500 N/m at B and k = 620 N/m at C,…

Q: The value of α20 for copper is 0.00393, so find the value of α for 0 °C and for 50 °C.

A: Resistance Temperature detectors are generally denoted by"RTD". As we know that the Resistance…

Q: a) b) c) A loaded cantilever beam is shown in Figure 3. Determine the horizontal and vertical…

Q: Find the moment of inertia about centroidal XX axis width=6 m Depth=10 m

A: Given data : Width is denoted by b Depth is denoted by d Required : Moment of inertia about…

Q: A seamless cover plate for a full face gasketed, flanged joint has been designed. If a material with…

A: Given Data: Pitch circle diameter, d=477 mm Pressure, P=852 kPa

Q: Q4: For the following state of stresses, find 1- principal stresses. 2. Principal direction 3.…

Q: Consider two liquids of densities p₁ = 1000 kg/m³ and p2 = 800 kg/m³ that are initially flowing in…

Q: Two industrial steel pipes are carrying 200 °C steam. The internal diameter of both pipes are 2.0 cm…

A: First option is correct.

Q: 1. Determine the work done by 1-kg fluid system as it expands slowly within the piston-cylinder…

Q: Consider a vector field v(x, y, z) defined by v = (sin y - cos z)i + (2x + cos z) cos(y)j + (x − sin…

Q: The bar AB has a built-in support at A. An external force F=25kN is applied at B (5,6,1)m, towards…

Q: The air, supplied at the rate of 249.57 gal per second to refrigerated coil, has a saturation…

A: Write the given data. ma=249.57 gal/s=249.578.34 lb/sωs=280 grains water/lb of dry air=0.280 g…

Q: A circular shaft of diameter 120 mm is welded to a rigid plate by a fillet weld of size 6 mm. If a…

Q: (1)DUAL-1-(1/)* -'[{af* = 1}/{ka(£ − 1)+ a 1 where: -compression ratio ·eple, - pressure ratio 8-…

A: Dear student, as the notations are not clearly visible, so I have taken standard notations for the…

Q: A thick-walled, stainless steel (AISI 316) pipe of inside and outside diameters D; = 25 mm and Do =…

Q: Redraw when the rack AB is at 89o angle. What are the other two angles belonging to the triangle…

A: When the rack AB is at 89o angle. Draw the diagram as given above.

Q: What are the different types of grooves found in belt drive?

A: Belt Drives are used to transmit powers from one shaft to another shaft while pulley at the same or…

Q: A helical gearset has 1.5 mm module and a pressure angle of 20°. The width of gears is 40 mm, the…

A: Given Data: The module of the gearset, m=1.5 mm Pressure angle, 20 Width of the gears, b=40 mm…

Q: /20 A particle moves along the positive x-axis with an acceleration a, in meters per second squared…

A: Given:At x=40 mm: a1=2 m/s2v1=0.4 m/sAt x=120 mm, a2=4 m/s2

Q: Q.4) For 30 wt% Sn- 70 wr% Pb alloy at 125 °C, (a) what phases are present? (b) What are the…

Q: Determine the work done Force applied=0.033 N Displacement=0.1 m

Q: A simple truss structure is shown in the following Figure. Point B is pin supported, and point C is…

Q: 1. The assembly has the diameters and material indicated, and has the four axial loads applied (two…

Q: There are two sealed tank linked by a U-tube. If the pressure in the left and right tank are P1 and…

A: Given the pressure in the left and right tank are P1 and P2 respectively,the fluid in the U-tube has…

Q: In the piezometers of the figure shown, liquid stands 1.37 m above point M. What is the pressure at…

A: As per our guidelines we are supposed to solve only 3 subparts if multiple subparts are asked .…

Q: Water flows through a 10 mm diameter and 250 m long smooth pipe at an average velocity of 0.1 m/s.…

A: Diameter of pipe=10mm Long =250mm Velocity =0.1m/s2 Density =997 kg/m3 Viscosity =855×10-6 N. S/m2…

Q: The water tank in Figure Q3b is inside a closed cabin, falling from a drop tower with an…

A: Given: Acceleration of the closed cabin: →y¨=3.81 m/s2 (downward) Diameter of the pipe: →D=20…

Q: Find the value of discharge Cross sectional area of flow-3.99 m2 Flow velocity=0.3 m/s

A: Given data : Flow velocity is denoted by V Cross sectional area is denoted by A Required :…

Q: 3. Torques are added to the beam at points B and D as shown. T₁ = 5 kip-feet, and T₂ = 2 kip-feet: w…

Q: If the outside barometric pressure reading shows 0.285235 ft Hg. What is the airplane’s vertical…

A: Given:Barometric pressure reading outside the airplane's, h=0.285235 ft HgFind: The airplane's…

Q: Prob. 2:- A U-tube acting as a water tank is shown in the figure. Determine: (a) Velocity of water…

Q: Specify a circularity tolerance of .001 for the conical taper on the part in the drawing below. A.…

Q: Calculate the final output using the Centroid method for the following strength values Provide step…

Q: Reslove Force of having magnitude 6 N along X positive direction. If the value of angle at which…

A: Given data : Angle with horizontal=θ Force=F Required : Force in X direction

Q: 4. An ideal vapour-compression refrigeration cycle operates at steady state with Refrigerant 134a as…

Q: Problem Solving. Solve the following problems completely. 5. Motors from two different manufacturers…

Q: You work as a junior engineer in a factory and the supervisor has asked you to perform certain…

Question

3.2 Two forces and a couple are applied to the beam in an attempt to lift it.
Replace this force system by an equivalent force-couple system with the force
acting at (a) point A; and (b) point B.
2m
36 kN
b
3 m
20 kN
2 m
B
94 kN-m
X

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The four forces shown act on the rollers of an in-line skate. Determine the equivalent force-couple system, with the force acting at O (the ankle joint of the skater).
An 8-m long cantilever beam is loaded with vertical forces A = 60 kN and B = 108 kN, separated by a distance d = 5.6 m, as shown. Replace the two forces with a single equivalent force R and determine the distance x-bar (x¯) from the left end of the beam to the line of action of R.
A 500-N force is applied to a bent plate as shown. Determine (a) an equivalent force-couple system at B, (b) an equivalent system formedby a vertical force at A and a force at B.
An overhead view of a portion of an exercise machine is shown. If the tension in the cable is T = 750 N, determine the equivalent force-couple system at (a) point B and at (b) point O.
The tension in cable AB is 17 kN. Replace this force as it acts on point A by an equivalent force-couple system at O. Point B is located at the center of the container top.
To keep a door closed, a wooden stick is wedged between the floor and the doorknob. The stick exerts at B a 175-N force directed along line AB . Replace that force with an equivalent force-couple system at C.
Three cables are attached to a bracket as shown. Replace the forces exerted by the cables with an equivalent force-couple system at A
reduce the given loading system to a force-couple system at point A.
As an adjustable brace BC is used to bring a wall into plumb, the force-couple system shown is exerted on the wall. Replace this force couple system with an equivalent force-couple system at A if R=21.2 lb and M=13.25 lb·ft.
The force-couple system shown acts on a trapezoidal plate. a. Determine the value of M1 if the system shown is equivalent to a single force acting at point C. b. The system shown is equivalent to a force-couple system consisting of R and M2 = 3000 kip-in clockwise. If M1 in this case is 120 kip-in counterclockwise, determine the point of action of the resultant force R along line CD.
A 160-lb force P is applied at point A of a structural member.Replace P with (a) an equivalent force-couple system at C, (b) an equivalent system consisting of a vertical force at B and a second force at D.
A couple M and the three forces shown are applied to an angle bracket. Find the moment of the couple if the line of action of the resultant of the force system is to pass through ( a) point A , (b) point , (c) point C.