3.23 i (a) A point charge Q lies at the origin. Show that div D is zero everywhere except at the origin. (b) Replace the point charge with a uniform volume charge density p,o for 0 < r < a. Relate p,o to Q and a so that the total charge is the same. Find div D everywhere.

3.23 i (a) A point charge Q lies at the origin. Show that div D is zero everywhere except at the origin. (b) Replace the point charge with a uniform volume charge density p,o for 0 < r < a. Relate p,o to Q and a so that the total charge is the same. Find div D everywhere.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

If the measured phosphorus profile is represented by a Gaussian function with diffusivity D=3atoms/cm3nd dose is 100000atoms per cm3 nd depth is 1mm nd concentration is 101000 atoms/cm3 ...find diffusion time
Calculate the linear charge density (nC/m) when the inner diameter of the pipe is 19.6 mm and the wire diameter is 137 μm. a voltage of 827 V is connected between the wire and the pipe. Calculate it by using C=2πϵ0*L/r(a)/r(b), as a cylinder capacitor.
A copper wire of 2mm diameter with conductivity of 5.8*10 7S/m and electron mobility of 0.00032m 2 / V-s is subjected to anelectric field of 20mV/m. Find(i) The charge density of free electrons(ii) The current density(iii) The current flowing in the wire(iv) The electron drift velocity
solve a,b and c please. In a concentric spherical electrode system, the outer radius is 15cm, the perforation of the insulator between the spheres since its resistance is 90 kV / cm, a) Obtain the equation for the breakdown voltage. b) Since 300kV is applied between the electrodes, r1 (inner radius) can be taken to prevent piercing of the system. what range are the values? c) What is the maximum voltage value that the system can withstand?
What are electron,hole,intrinsic carrier concentration, and energy band gap in si with (a) Nd= 4×10¹⁶ cm⁻³ and Na=1×10¹⁶ cm⁻³ and (b) additional 6×10¹⁶ cm⁻³ of ND ? Note: use Effective density of conduction band= 2.8 ×10¹⁹ cm⁻³ .Effective density of valance band =1.04 × 10¹⁹cm⁻³.T=300K ,Boltzmann constant = 1.38 x 10⁻²³ kgs⁻²K⁻¹
The number n of free electrons per m3 in the current carrying cable is iBL/VHeA. (A is the crosssectional area of it.) Where n is obtained from? a. The current density J’s expression b. Ohm’s Law c. The resistivity’s expression E/J d. Faraday’s Law.
" A sheet charge, ρS = 4 nanoC/m2 is present at the plane x = 4m in free space. Find the electric field intensity E in N/C at T(3, 5, -4) ." QUICKLY AND NO SHORTCUTS PLEASE
A steady current of 400 µA flows through the plane electrode separated by a distance dof 0.5 cm when a voltage of 12 kV is applied. Determine Townsend's first ionization coefficient if a current of 80 A flows when the separation distance is reduced to 0.1 cm, and the field is kept constant at the previous value.
The outer radius of a coaxial cylindrical electrode system is given in 32 cm. The system is the most suitable sized according to puncture. Penetration of the insulator between the cylindrical layers Its strength is Ed = 72 kV / cm and the relative dielectric constant of the insulator is Er1 = 10 a) - Calculate the capacity of the system and get the highest possible application without puncture to the system. Please respect what the voltage should be b) - For the case of U = 120 kV application, the maximum and minimum occurrence on the system Calculate the electric field values?
12 - ))If the distance between two point charges of -4 nC and +12 nC is 40 cm, calculate the electrical potential at the midpoint between these charges.A) 60 VB) 120 VC) 180 VD) 240 V
Q: P. type semiconductor with length (I=5mm), the cross-section area of (A=0.5 mm^ 2 ). , and resistance (R = 250Omega) . Calculate the exact number of the majority (p p ) and the minority (n p ) carriers. Also, calculate the number of acceptor atoms (N A ) if the intrinsic carrier ( Pi j =2*10^ 20 /m^ 7 ) . Given the mobility for the electrons ( mu k =0.4m^ 2 /V.s) and for the holes ( mu 1 =0.2m^ 2 N.s) Note: use these equations to solve the problem. sigma tp = sigma e + sigma ll =n p e mu e +p p e ll n i ^ 2 =n p p p Compare your results if you use this equation instead for sigma tp with sigma tp = sigma p =p p e mu h
Q: P. type semiconductor with length (I= 5mm), the cross-section area of (A = 0.5m * m ^ 2) , and resistance (R=25092). Calculate the exact number of the majority (p p ) and the minority (n p ) carriers. Also, calculate the number of acceptor atoms (N A ) if the intrinsic carrier (n i =2*10^ 20 /m^ 3 ) . Given the mobility for the electrons mu i =0.4m^ 2 /V.s) and for the holes ( mu k =0.2m^ 2 /V ,s )