3.4-18/ A prismatic bar AB of length L and solid circular cross section (diameter d) is loaded by a distributed torque of constant intensity t per unit distance (see figure). (a) Determine the maximum shear stress Tmu in the max bar. (b) Determine the angle of twist o between the ends of the bar. L-

3.4-18/ A prismatic bar AB of length L and solid circular cross section (diameter d) is loaded by a distributed torque of constant intensity t per unit distance (see figure). (a) Determine the maximum shear stress Tmu in the max bar. (b) Determine the angle of twist o between the ends of the bar. L-

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.4.18P: A prismatic bar AB of length L and solid circular cross section (diameter d) is loaded by a...

See similar textbooks

Similar questions

-8 An aluminum bar of solid circular cross section is twisted by torques T acting at the ends (see figure). The dimensions and shear modulus of elasticity arc L = 1.4 m, d = 32 mm, and G = 28 GPa. Determine the torsional stiffness of the bar. If the angle of twist of the bar is 5º, what is the maximum shear stress? What is the maximum shear strain (in radians)? If a hole of diameter d/2 is drilled longitudinally through the bar, what is the ratio of the torsional stiffnesses of the hollow and solid bars? What is the ratio of their maximum shear stresses if both arc acted on by the same torque? If the hole diameter remains at d/2, what new outside diameter d2will result in equal stiffnesses of the hollow and solid bars?
A prismatic bar AB with a solid circular cross section (diameter d) is loaded by a distributed torque (see figure). The intensity of the torque, that is, the torque per unit distance, is denoted i(x) and varies linearly from a maximum value iAat end A to zero at end B. Also, the length of the bar is L and the shear modulus of elasticity of the material is G. Determine the maximum shear stress in the bar. Determine the angle of twist between the ends of the bar.
A tubular bar with outside diameterd2= 4.0 in, is twisted by torques T = 70,0 kip-in. (see figure). Under the action of these torques, the maximum tensile stress in the bar is found to be 6400 psi. Determine the inside diameter rtf of the bar. If the bar has length L = 48.0 in. and is made of aluminum with shear modulus G = 4,0 × 106 psi, what is the angle of twist d (in degrees) between the ends of the bar? (c) Determine the maximum shear strain y (in radians)?
A vertical pole of solid, circular cross section is twisted by horizontal forces P = 5kN acting at the ends of a rigid horizontal arm AB (see figure part a). The distance from the outside of the pole to the line of action of each force is c = 125 mm (sec figure part b) and the pole height L = 350 mm. (a) If the allowable shear stress in the pole is 30 MPa, what is the minimum required diameter dminof the pole? (b) What is the torsional stiffness of the pole (kN · m/rad)? Assume that G = 28 GPa. (c) If two translation al springs, each with stiffness k =2550 kN/m, are added at 2c/5 from A and B (see figure part c), repeat part (a) to find dmin. Hint: Consider the pole and pair of springs as "springs in parallel."
A stepped shaft of solid circular cross sections (see figure) has length L = 0.80 m, diameter d2= 40 mm, and diameter d2= 30 mm. The material is steel with G = 80 GPa. Determine the strain energy U of the shaft if the angle of twist is 1.0º.
A stepped shaft of solid circular cross sections (see figure) has length L = 45 in., diameter d2=1.2 in., and diameter d1= 1.0 in. The material is brass with G = 5.6 × 106 psi. Determine the strain energy U of the shaft if the angle of twist is 3.0°.
A circular tube of inner radius r1and outer radius r2is subjected to a torque produced by forces P = 900 lb (see figure part a). The forces have their lines of action at a distance b = 5.5 in. from the outside of the tube. (a) If the allowable shear stress in the tube is 6300 psi and the inner radius r1= 1.2 in., what is the minimum permissible outer radius r2? (b) If a torsional spring of stiffness = 450 kip-in./rad is added at the end of the tube (see figure part b), what is the maximum value of forces P lithe allowable shear stress is not to be exceeded? Assume that the tube has a length of L 18 in., outer radius of r2= 1.45 in. and shear modulus G = 10.800 ksi. Hint: Consider the tube and torsional spring as “springs in parallel.”
A long, thin-walled tapered tube AB with a circular cross section (see figure) is subjected to a torque T. The tube has length L and constant wall thickness t. The diameter to the median lines of the cross sections at the ends A and B are dAand dB, respectively. Derive the following formula for the angle of twist of the tube: Hint: If the angle of taper is small, you may obtain approximate results by applying the formulas for a thin-walled prismatic tube to a differential element of the tapered tube and then integrating along the axis of the tube.
A solid circular bar of steel (G = 1L4 × 106 psi) with length L = 30 in, and diameter d = 1.75 in, is subjected to pure torsion by torques T acting at the ends (see figure). Calculate the amount of strain energy V stored in the bar when the maximum shear stress is 4500 psi. From the strain energy, calculate the angle of twist 0 (in degrees).
The bar shown in the figure is tapered linearly from end A to end B and has a solid circular cross section. T lie diameter at the smaller end of the bar is dA= 25 mm and the length is L = 300 mm. The bar is made of steel with shear modulus of elasticity G = 82GPa. If the torque T = 180 N · m and the allowable angle of twist is 0.3°, what is the minimum allowable diameter dBat the larger end of the bar?
A vertical pole of solid, circular cross section is twisted by horizontal forces P = 1100 lb acting at the ends of a rigid horizontal arm AB (see figure part a). The distance from the outside of the pole to the line of action of each force is c = 5.0 in. (see figure part b) and the pole height is L = 14in. (a) If the allowable shear stress in the pole is 4500 psi, what is the minimum required diameter dminof the pole? Find the torsional stiffness of the pole (kip-in./rad). Assume that G = 10,800 ksi. If two translational springs, each with stiffness k = 33 kips/in., are added at 2(75 from A and B (see figure part c), repeat part (a) to find dmin. Hint: Consider the pole and pair of springs as "springs in parallel."
A uniformly tapered tube AB with a hollow circular cross section is shown in the figure. The tube has constant wall thickness t and length L, The average diameters at the ends are dAand dB= 2dA. The polar moment of inertia may be represented by the approximate formula Ipttd3t4[see Eq. (3-21)]. Derive a formula for the angle of twist e of the tube when it is subjected to torques T acting at the ends.