3.6. A short compression member with Do = 2Di is to support a dead load of 25 tons. The material is to be 4130 steel, W QT 1100F. Calculate the outside and inside diameters on the basis of a yield strength of 114 ksi and factor of safety of 2.

3.6. A short compression member with Do = 2Di is to support a dead load of 25 tons. The material is to be 4130 steel, W QT 1100F. Calculate the outside and inside diameters on the basis of a yield strength of 114 ksi and factor of safety of 2.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.9.6P: A steel pad supporting heavy machinery rests on four short, hollow, cast iron piers (see figure)....

See similar textbooks

Related questions

Q: Calculate the stress developed in a steel rod that is 25 mm in diameter when a 70kNaxial tensile…

A: Diameter of rod=d= 25 mm Cross- sectional area= A= (π/4)×d2 = (π/4)×252= 490.873 mm2 Axial load=P=…

Q: PROBLEM (3´) A 2-in.-diameter bar 6 ft long, shortens 3/64 in. under an axial load of 40 kips. the…

Q: A circular rod 16 mm dia and 500 mm long is subjected to a tensile load of 40 kN. The modulus of…

Q: A 13-kN hydraulic press for removing and reinstalling bearings in small-to medium-sized electric…

A: Given: Su = 345 MPa Load, P = 13 kN

Q: Calculate the reliability if information about both the strength data (170 ± 20 MPa) and stress data…

A: Given: The standard deviation based on strength data = 2x20 = 40 MPa The standard deviation based on…

Q: A 13-kN hydraulic press for removing and reinstalling bearings in small-to medium-sized electric…

A: width of iner fibre,bi=25 mmthickness,h=28 mmr1=38 mmr2=66 mmthickness of inner fibre,ti=10…

Q: (8) A tension member subjected to a load of 30,000 lb has a cross section % in. by 6 in. and is…

A: given; load(P)=30000lbcross section hole diameter (d1)=6 inpiercing hole diameter(d2)=1 infactor of…

Q: please answer question in picture. thank you in advance

A: Given data: Diameter of bar = 12.83 mm Length of bar L = 55 mm Load applied F = 200 KN Change in…

Q: 450-mm-long AISI 1020 steel rod is subjected to a tensile load of 55 kN. The allowable tensile…

A: Given Length = 450 mm Tensile load = 55 kN = 55 X 103 N Allowable tensile stress = 140 MPa = 140…

Q: (a) Calculate the tangential and longitudinal stresses in the steel. (b) To what value may the…

Q: 12. Problem 6: A hollow cylindrical steel column has an outer diameter of 4 inches and inner…

Q: A steel bar is desired to be formed until it has a final length of 1.8m. What length should the bar…

Q: A 1.2 m pulley is fastened to a 5 in shaft by means of a square key with 140 mm long. What force…

A: Given Data The diameter of the pulley is: D=1.2 m the diameter of the shaft is: d=5 in=127 mm The…

Q: The figure shows a welded-arm. The arm is welded using ! normal yield strength of 393MPa. If the…

A: Given data: The given weld size from the figure is The radius of the weld is

Q: Problem No.2 A bar of circular cross-section is subjected to alternating tensile forces varying from…

Q: A cylinder head stud has a diameter of 14mm at the bottom of the thread. If the maximum tensile…

A: Given data: The diameter of the stud, d = 14 mm. The maximum tensile stress, σ=30 MPa. Write the…

Q: A bracket is designed with a pin-pin horizontal tie rod supporting a boom that is also pinned at two…

A: Given data as per question vertical load =6 KN Tensile yield strength =400 Mpa Considering FBD of…

Q: Figure shows a tie bar made of steel. When bolted between A and B double brackets, it is to be…

A: Given Data, P= Tensile load in the bar = 100 KN The bolt is of double brackets, so the shear load…

Q: 3. A cylindrical metal rod of 50mm diameter and 3m length is subjected to a tensile load of 150KN.…

A: Strain is the deformation in the material per unit length. True strain is the natural log of the…

Q: Jason took a steel rod, 15.29-mm in diameter, and held snugly (but without any initial stress)…

A: Given: The diameter of rod, D = 15.29 mm The coefficient of thermal expansion, α = 13.6x10-6 mm/mmoC…

Q: Suppose that you are making preliminary design calculations for a deep submersible vehicle that is…

A: Given that, Radius of hemispherical shell, r=1.5 m,Internal pressure inside the shell, Pi=1×105…

Q: Calculate the stress developed in a steel bar that is 50 mm by 25 mm when a 70kNaxial tensile load…

Q: problem 1 pls complete solution

Q: 3.6. A short compression member with Do = 2Di is to support a dead load of 25 tons. The material is…

A: Given data Outer diameter, Do= 2Di F=25 tons Material is 4130 steel, WQT 1100 F Yield strength =…

Q: 6. A cylındrical copper (E=110GPA) rod with length of 380mm, yield strength of 240MPA, is subjected…

A: Solution :- Given data :- E =110 GpaLoad P =66000 NLength of rod L =380 mm

Q: Find the Brinell hardness number of the material if the indenter diameter is 10mm and the produced…

Q: A bar is subjected to fluctuating tensile load from 20 kN to 100 kN .The material has yield strength…

Q: Calculate the allowable (ASD) tensile strength of a WT125X22.4 with a transverse weld to its flange…

A: INTRODUCTION: There are two types of weld joints: fillet weld and butt weld. The fillet weld is…

Q: Example 7.4 A steel plate subjected to a force of 5 kN and fixed to a channel by means of three…

A: m20 Given data =>step1 Syt=380mpa Fos=3

Q: Taking the safety factor as 2 for the loading condition shown in the figure, we can calculate the…

A: Given: d=100mm Syt = 250 MN / m2 Sys = 140 MN / m2 E = 200 GPa μ=0.3 N = 2

Q: In the cage system in Figure 3, circular section steel bars will be used. Calculate the minimum…

A: The free body diagram of the truss is as follows: Calculate the moment about point D as follows:…

Q: A 13-kN hydraulic press for removing and reinstalling bearings in small-to medium-sized electric…

A: Write the given data as follows.

Q: Calculate each of the following under 20 kN load on a structure given below where all pins have a…

A: Given details: P=20 kNd=10 mmζy=300 MPan=2

Q: The state of stress at a point in a steel bar is represented in the stress element seen below. The…

A: Given- σy=260 MPaFOS=2

Q: A 12” X 16”simply supported pine wood beam is being considered to carry a uniform load distribution…

A: Load = 20 kips Ultimate tensile stress = 4500 psi FOS = 2.5

Q: [30] Problem 2: A bracket is designed with a pin-pin horizontal tie rod supporting a boom that is…

A: GivenVertical load P=6kNyield strength σy=400MPadaimeter of the tie rod d=12mmdaimeter of the pin…

Q: Calculate the riveted joints, find its efficiency and draw a suitable sketch. Thickness of the…

A: Another name of rivet joint is lozenge joint. Selection of material σt=80 mpaζ=65 mpaσc=160 mpa

Q: A hollow compression member with circular cross section having outer diameter 2 times the inner…

Q: 450 mm long a ISI 1020 Steel long is subjected to a tensile load of 55 kilo Newton the allowable…

A: Given information: AISI 1020 steel: E = 207000 MPa We have to calculate the area of rod using the…

Q: Problem (1): The rigid, horizontal slab is attached to two identical copper rods. There is a gap A…

Q: A double riveted lap joint is made between 15mm thick plates. The rivet diameter and pitch are 25 mm…

Q: A copper rod of 50mm diameter is surrounded by a steel tube of 100mm external diameter, the ends…

A: Given data diameter of copper rod (d) = 50 mm outer diameter of steel tube (D) = 100 mm…

Q: A 1 in x2 in ductile cast iron bar should operate for 9 years at 650 ° C. What is the maximum load…

A: Given:time,t=9 years =9*365*24 t=78840 hLarson miller,LM=T1000(36+0.78lnt)genaral Larson miller…

Q: A round bar, 40 mm in diameter, has a shallow circumferential notch with a depth c = 2 mm with a…

A: The stress concentration caused by the notch of depth c and root radius r, σmaxσnom=1+αcr1/2 α=2…

Q: Q1: As shown in Fig. 1, there is a gap between the aluminum bar and the rigid slab that is supported…

A: Dear student as you have posted multiple Question , as per the policy i can answer only one question…

Q: For a circular column having its ends hinged, the slenderness ratio is 160. The L/ d ratio of the…

A: Given, Slenderness ratio = λ = 160 Slenderness ratio is given by ratio of length of column to the…

Q: A bar is subjected to fluctuating tensile load from 20 kN to 100 kN. The material has yield strength…

A: Given, Minimum tensile load = Fmin = 20 kN = 20,000 N Maximum tensile load = Fmax = 100 kN = 100,000…

Concept explainers

Numerical Calculations

In the mid-20th century, the availability and the growth in power of digital computers led to the increase in the mathematical model in the field of engineering and science. The analysis of these detailed models needs to be increased.

Question

Show your COMPLETE solution. Use 4 decimal places for the final answer.

3.6. A short compression member with Do = 2Di is to support a dead load of 25 tons. The
material is to be 4130 steel, WQT 1100F. Calculate the outside and inside diameters on the
basis of a yield strength of 114 ksi and factor of safety of 2.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A steel pad supporting heavy machinery rests on four short, hollow, cast iron piers (see figure). The ultimate strength of the cast iron in compression is 400 MPa. The total load P that may be supported by the pad is 900 kN. Using a factor or safely 3.0 with respect to ultimate strength, determine the outer diameter of the pier if the thickness, is of the cross section is 12 mm.
An inflatable structure used by a traveling circus has the shape of a half-circular cylinder with closed ends (see figure). The fabric and plastic structure is inflated by a small blower and has a radius of 40 ft when fully inflated. A longitudinal scam runs the entire length of the "ridge" of the structure. If the longitudinal scam along the ridge tears open when it is subjected to a tensile load of 540 pounds per inch of seam, what is the factor of safety n against tearing when the internal pressure is 0,5 psi and the structure is fully inflated?
An aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the aluminum is shown in Fig. 1.34. The initial straight, line part of the curve has a slope (modulus of elasticity) of 10.6 × 106 psi. The bar is loaded by tensile forces P = 44.6 k and then unloaded. (a) That is the permanent set of the bar? (b) If the bar is reloaded. what is the proportional limit? hint: Use the concepts illustrated in Figs. l.39b and 1.40.
A flanged bolt coupling is used to connect a solid shaft 90 mm in diameter to a hollow shaft 100 mm in outsude diameter and 90 mm in inside diameter. If the allowable aring stress in the shafts and the bolts is 60 MPa, how many 10 mm diameter steel bolts must be used on a 200 mm diameter bolt circle so that the coupling will be as strong as the weaker shaft?
A mild steel tie-rod has to carry an axial load of 60KN. The maximum permissible stress is 200N/mm2. Calculate a suitable diameter for the rod.
For same problem setup in Q1 except for the length, if the yield strength is 145 MPa, calculate the critical length under which the column would fail by yield and over which the column would fail by buckling.
PROBLEM 2A tri metallic bar is uniformly compressed by an axial force P=12kN applied through a rigid end plate. The bar consists of a circular steel core surrounded by brass and copper tubes. The steel core has a diameter 10mm, the brass tube has an oute diameter of 15mm and the copper tube has an outer diameter of 20mm. E for steel =210Gpa, E for brass =100GPa and E for copper is 120GPa. Calculate the compressive stress of each metal due to force P.
Problem 18.20, please show all work? Section 18.7 Axially Loaded Steel Machine PartsFor Problems 18.18 through 18.21, use the Euler–Johnson formulas, Equations (18.9) and ( 18.10), and a modulus of elasticity of 30,000,000 psi. 18.18 Calculate the allowable axial compressive load for a bar of rectangular cross section that measures 1 in. by 2 in. and is 20 in. long. The member is made of AISI 1040 hot-rolled steel. Use a factor of safety of 3.5 and assume the member is pin-connected. 18.19 Compute the required diameter of a piston rod of AISI 1040 hot-rolled steel with a length of 20 in. The rod is subjected to an axial compressive load of 6000 lb. Use a factor of safety of 2.5. Assume that the rod is pin-connected. 18.20 Compute the required diameter of an air cylinder piston rod of AISI 1040 hot-rolled steel. The rod has a length of 54 in. and is subjected to an axial compressive load of 1900 lb. Assume pinned ends. Use a factor of safety of 3.5. 18.21 Compute the required…
A cylinder head stud has a diameter of 14mm at the bottom of the thread. If the maximum ten sile stress allowed in the material is 30MPa. Calculate the safe load the stud can carry.
A member in tension in a machine frame is subjected to a continuous load of 5.00 kN. Its length is 750 mm and it is made of a carbon steel tube with an outer diameter of 17 mm and an inner diameter of 12 mm. Calculate the tensile stress (in MPa).
Design a turnbuckle subjected to a load of 50 kN with permissiblestresses are in 166.67 Mpa in tension , 83.33MPa in shear and 166.67 MPa incrushing. (Please provide a handwritten solution, thank you)
Given a 1.3meter Wide Flange steel compression member with A=4,118mm2, Ix=87,958,354mm4 and Iy=3,574,253mm4 with Fy = 345MPa. Calculate the critical buckling stress in MPa if both ends are fixed or rigid. Express your answer in 2 decimal places.