300 mm 200 mm- 500 mm

Q: Determine the average normal stress in rod AB if the load has a mass of 50 kg. The diameter of rod…

A: Given figure mass of the load = 50 Kg Weight of the load

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. The…

A: Given that: diameter of rod 1 = 15 mm diameter of rod 2 = 28 mm It is required to determine the…

Q: a. Determine the torque T and the radius of the elastic-plastic boundary. b. Determine the residual…

A: The diameter f the solid shaft is D=100 mm. The elastic shear strength is τY=150 Mpa. The shear…

Q: The 1-in.-diameter rod is subjected to the loads shown. Determine the state of stress at point B,…

A: d=1in Draw the free diagram of the problem by converting the eccentric loads into the loads and…

Q: Take the section AB, construct the FBD and label the internal loadings, determine the normal stress…

A:

Q: The members of the truss shown below have a cross-sectional area of 10,000 mm2. Determine the…

A:

Q: The steel bracket is used to connect the ends of two cables. If the applied force P = 1.50 kip,…

A: Draw the free body diagram.

Q: The steel pipe has an inner diameter of 2.75 in. and an outer diameter of 3 in. If it is fixed at C…

A: Since the magnitude of the direct shear stress compared to the twisting and bending stresses is very…

Q: Please Show work clearly and show free body diagram if possible and be sure with the positive and…

A:

Q: The members of the truss shown below have a cross-sectional area of 10,000 mm2. Determine the…

A:

Q: Determine (a) the principal stresses and (b) the maximum in-plane shear stress and average normal…

A:

Q: The square steel plate has a thickness of 10 mm and is subjected to the edge loading shown.…

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Q: The pedal crank for a bicycle has the cross section shown. If it is fixed to the gear at B and does…

A: Given data: The magnitude of the force subjected on the pedal is; F = 50 lb.   Draw the…

Q: The assembly consists of a solid 15 mm diameter rod connected to the inside of a tube using a rigid…

A:

Q: Determine the equivalent state of stresses in an element at the point representing (a) the principal…

A:

Q: Q3: The plate has a width of 0.5 m. If the stress distribution at the support varies as shown,…

A: Given :- width of plate(b)=0.5m   To find :- Force(p) and distance(d)

Q: The 200-mm-diameter aluminum cylinder supports a compressive load of 300 kN. Determine the average…

A:

Q: The bolt is fixed to its support at C. If a force of 18 lb is applied to the wrench to tighten it,…

A: Given Data: The applied force is F = 18 lb. The length from force is l = 6 in. Diameter of shank is…

Q: The tank of the air compressor is subjected to an internal pressure of 90 psi. If the inner diameter…

A: Write the given data: Understand that the stress generated at point A will be the tangential stress…

Q: Determine the maximum normal stress developed in the bar when it is subjected to a tension of P = 2…

A: Given:- P=2kip,Width of section of bar with hole,w1=1.875 inch,Width of section of bar without…

Q: Three forces of 500 lb, 800 lb, and 600 lb are applied to the end of the 2-in-diameter bar, as…

A:

Q: The bar has a diameter of 40 mm. Determine the state of stress at point A and show the results on a…

A: Section properties can be determined as

Q: Determine Value of x if the Normal stress at rod is equal to the stress at rectangular pipe A =400…

A:

Q: The steel pipe has an inner diameter of 2.75 in. and an outer diameter of 3 in. If it is fixed at C…

A: Write the given data: Understand the effects of the 20 lb force on the member CD as shown in the…

Q: The rod has a diameter of 40 mm. If it is subjected to the force system shown, determine the stress…

A: Understand that the point A lies on the outer periphery of the shaft on the z axis. The Torsional…

Q: The spreader bar is used to lift the 2000-lb tank. Determine the state of stress at points A and B,…

A: Given data as per question weight of tank =2000 lb ∑Fy=02000−2Fcos30=0F=1154.7 lbInternal forces and…

Q: The 1-in.-diameter rod is subjected to the loads shown. Determine the state of stress at point A,…

A:

Q: The clamp presses the smooth surface at E when tightening the screw. If the tension in the bolt is…

A: Given data as per question Tension in the bolt =40 kN   Support reaction are shwn on FBD (a)Internal…

Q: The 1.4-kip load P is supported by two wooden members of uniform cross section that are joined by…

A: Given Data: The load on member is P = 1.4 kip. The cross-section area is A = 3 in ×5 in. The angle…

Q: Determine the average normal and shear stresses at a cross section (a-a) for e-65. The member has a…

A: Draw the F.B.D of the given cut section of the element.

Q: Q3: The plate has a width of 0.5 m. If the stress distribution at the support varies as shown,…

A: Answer:Step 1:Given data: width of plate =b=0.5m                       length of pipe ,  l=4mto find…

Q: The assembly consists of a solid 15 mm diameter rod connected to the inside of a tube using a rigid…

A:

Q: The solid 1.35-in.-diameter rod is subjected to a uniform axial distributed loading along its length…

A:

Q: Determine the maximum normal stress developed in the bar when it is subjected to a tension of P = 2…

A: At fillet rh=0.251.25=0.2wh=1.8751.25=1.5   From the table  The stress concentration factor,  K=1.73

Q: 2. The coping saw has an adjustable blade that is tightened with 8 mm a tension of 40 N. 3 mm A 75…

A:

Q: The joint is subjected to the force system shown. Determine the state of stress at points A and B,…

A: Let us consider the equilibrium of the lower section a-a Net force in the x-direction is zero…

Q: A 600 kg material is hung from the end of the horizontal bar BD as shown. Determine the stress on…

A:

Q: The plate has a thickness of 20 mm and the force P = 3 kN acts along the centerline of this…

A: Given, thickness of the plate, t=20mm=0.02m Force on the plate, P=3kN We need to Plot the…

Q: Determine the state of stress at point A on the cross section of the pipe assembly at section a-a.…

A:

Q: The solid 0.85-in.-diameter rod is subjected to a uniform axial distributed loading along its length…

A:

Q: The horizontal force of P = 80 KN acts at the end of the plate. The plate has a thickness of 10 mm…

A: Given data as per question P = 80KN The thickness of plate =10 mm Area=10×200=2000 mm2 we know…

Q: The box beam is subjected to the 26-kN force that is applied at the center of its width, 75 mm from…

A: Given, P = 26 kN

Q: Determine the maximum distance d to the edge of the plate at which the force P can be applied so…

A: Given, Load=P Distance of the load from the bottom=d Thickness of the plate= 200mm Solution Tensile…

Q: The steel pipe has an inner diameter of 2.75 in. and an outer diameter of 3 in. The pipe is fixed at…

A:

Q: The rectangular bar has a width of w = 3.50 in. and a thickness of t= 1.50 in. The normal stress on…

A: Given   Normal stress = 6 ksi       Thickness, t = 1.5 in           Width, W = 3.5 in Find   Load, P…

Q: The rectangular bar has a width of w - 3.50 in. and a thickness of t - 1.75 in. The normal stress on…

A: Given:- w=3.50 int=1.75 in q=2b=3Normal stress= 6 ksiTo find:-a) Pb) τnetc) σmax    τmax

Q: If the box wrench is subjected to the 50-lb force, determine the principal stresses and maximum…

A: Draw the section a-a with shear force and bending moments.     Apply force equilibrium in the…

Q: Q 2: A cantilever beam has the profile shown so that it will provide sufficient clearances for large…

A: Given P = 115.33 kN = 115.33 × 103 N Centroid = 100 mm in Y axis To find Resultant normal stress at…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.