30KM DRAW THE SHEAR AND 3m MOMENET DIAGRAM WH# 5 KN /m COMPLETE SOLUTION . am Cs Scanned with CamScanner

Q: I 4m Ax вк 100KN E I 6m Dx 2m Tay Toy Draw the Shear force, Bending Moment and Normal force diagrams…

A:

Q: Determine the bar force member CD. All interior angles are 60 degrees. 1.5 kN 3 KN ... 2 kN F 1.5 m…

A:

Q: 1. Compute the vertical distance of link AB from pin E for the given set up if the tension in link…

A: Given:- The magnitude of the weight at GF = 800 lb The magnitude of the tension in link AB = 1500 lb…

Q: 300 N/m B C 2700 N m -3 m -3 m -3 m- RC RA

A:

Q: /Draw S.F.D and B.M.D 50 KN/m 20 kN/m 100 KNm 6m Gm 3m Shear Force Diagram S.F.D B.M.D

A:

Q: besign the steel reinforcement op a 400mm x600mm RC beam used to camy a pactored moment,mu-500KN.m.…

A: Using the Limit State method to design the steel reinforcement of the beam, We will design this beam…

Q: Determine the ff: 1. Force at member BC = Select] %3D 2. Force at member BD = [ Select ] 3. Force at…

A: Given: Truss with 5200 kN force  Find member forces We will use Lami's theorem as below

Q: SFD and BMD. Locate points of cont the elastic curve and compute the de 8 kN 8 kN 20 kN-m C

A:

Q: 4m C. L000 N 3m DE 3m F

A:

Q: draw shear and bending moment diagram. Show completed solution 45 KN 45 AN 71kN/m Lisat tist

A: As per guidelines we can solve one question at a time, please upload separately, Thanks Solution to…

Q: If the ma= 0.5 kg and må = 1.5 kg, determine the acceleration of ea block and the tension in the…

A:

Q: Determine the ff: 1. Force at member BC = [Select] 2. Force at member BD = [ Select] 3. Force at…

A:

Q: The possible location of shear centre of the channel section, shown below, is PQ R S

A: Answer : The possible location of shear centre is Point P. Explanation is given in next step.

Q: 9.35 KN /m 2m SOLVE FOR SHEAR FORCE DIAGRAM AND SHEAR MOMENT DIAGRAM 116 KN CS Scanned with…

A:

Q: s = 20 ft Determine the two possible angles so that the water strikes at B. VA = 40 ft/s 0 4 ft B 8…

A:

Q: حه shear stress Draw. V = 100KN حالم ده3 ده( 300

A:

Q: 1.5m 1.5m 1.5m 6. Determine the horizontal and vertical components of the pin forces at B, C, and D.…

A:

Q: /Draw S.F.D and B.M.D 50 KN/m 20 KN/m 100 kNm 1m Gm 3m 3m 5m Shear Force Diagram S.F.D

A: See in steps 2

Q: Calculate the axial normal stresses in section 1 and 2. A (1) 30 kN (2) 10 kN = 20 mm d, = 15 mm %3D

A:

Q: Determine the maximum negative shear at C. 4.5m. 4.5m. Pa45 kN O zoom image 38.75 kN 58.43 kN

A:

Q: rectangular footing 3 × 2 cted to a moment of 90 kNm

A: Given data Rectangular footing= 3×2m Column=420×420mm E=21×103kN/m2 μ=0.3

Q: Determine the bar force member CD. All interior angles are 60 degrees. ... 1.5 kN 3 KN 2 kN F 1.5 m…

A:

Q: /Draw S.F.D and B.M.D 50 KN/m 20 kN/m 100 KNm 3m 1m 5m Gm 3m Shear Force Diagram

A:

Q: A6 - storey with roof deck building has a total height of 21m. The computed base shear is 900 kN.…

A: Given data: Storey height= 21m Total no. of storeys= 6 Height of each storey= 3.5m base shear=Vb =…

Q: Calculate and draw the internal forces created at H section of the bracket beam?

A:

Q: Q: A quarter circle gate AB of 2m radius and 1 m wide, hinge at B, find the horizontal force F…

A: Draw the free body diagram. Taking moment about hinge, ∑MB=0F2=FH2F=FH

Q: A V, kN 2m 3 m B kN/m

A: Please find step by step solution below:

Q: 1りthe DYaw SFD and BM.D figure belowe. 275 KN B 金 トSm 3,6m lism 275 KN

A: Given data in question  Overhanging beam  Point loads Span length To find out  SFD BMD

Q: /Draw S.F.D and B.M.D 50 KN/m 20 KN/m 100 KNm 3m 1m 5m Gm 3m Shear Force Diagram

A: Given simply supported beam

Q: 2KH Goo Support reaction at point B=.

A:

Q: A 30m building has an average height of 3.0m each floor, has a weight of 3,000 KN for each floors…

A: Height of Building, h = 30 mNo of Floors = 303 = 10 floorsTotal seismic  weight of the building, WW…

Q: s = 20 ft Determine the two possible angles so that the water strikes at B. VA = 40 ft/s A 0 4 ft B…

A:

Q: What is the Maximum moment in kN-m. Given: w = 45, a = 3, b = 2, and c = 3. %3D w kN/m *cm> Rp am bm…

A:

Q: Situation 1. Knowing that de 3 m, determine the following: %3D 2m 2m 3m 3m de 4m 5kN SkN 10KN 4.…

A: In the figure a cable is mentioned and we are required to calculate the maximum tension, total…

Q: Compute the reaction of the cable CD. 100.0° 70.0° F A 30.0°? E 30.0° B 45.0 80 KN 30.0° Block 2 60…

A:

Q: Determine the slope at A and displaceme t C. El is constant. 5 kN-m B -1.5 m- -1.5m. - swer Key: 0 =…

A:

Q: Determine the resultant internal loadings of the cross-section at points E and F of the assembly. b…

A:

Q: 300 mm 200 mm B 60 N 60 N 400 mm 150 mm 150 mm Prob. 1-23

A: The both forces acting on each side of pipe can be transfered to center such that they create moment…

Q: Timet 60 kH 30 KN DRAW the shear and mament diagram with complete sokrtion

A:

Q: A square gate (4m x 4m) is located on the 45° face of a structure. The top edge of the gate lies 8 m…

A:

Q: Exercise, 120 Im 200 KN

A:

Q: Determine (a) the equations of the shear and bending moment curves for the beam and loading shown…

A:

Q: Draw a rough line of influence at the main point 9tf Зт 6m Зт

A: Please mention the main point location.  At where you want influence line diagram.

Q: The channel beam with b= 300 mm, h=150 mm, and constant thickness of t=15 mm is subjected to a shear…

A: To determine the shear flow at point A-

Q: Problem 4. Shear at point C 20 kN 20 kN D B C -3 m -3 m- -3 m- O+20KN-m -20KN-m O +25KN-m -25kN m

A:

Q: /Draw S.F.D and B.M.D 50 KN/m 20 KN/m 100 KNm 1m Gm 3m 3m 6m Shear Force Diagram S.F.D В.М.D

A:

Q: What is the Maximum moment in kN-m. Given: w1 = 48, w2 = 14, a 3, b = 3, and c =3. !3! %3D %3D %3D…

A:

Q: a slope at A b. slope at B c. deflection at the midpoint of the span.

A:

Q: Q2/ Determine the forces at the pin joint (F) and the roller support (G) ? 30KN 20 KN 2m BY 2m D 2m…

A: The equilibrium condition of an object exists when Newton's first law is valid. An object is in…

Frames

The trusses and frames are the two most important structural members of civil engineering. Trusses are the interconnection of links and other structural members. The interconnection with other members makes the system behave as a single member that supports and transfers loads. Trusses are generally two types, plane truss, and space truss. Frames on the other hand form the skeleton of any building construction. Frames are structures formed by the connection of beams, columns, slabs, and joists. These members provide the building with the required structural support.