Problem 4. Shear at point C 20 kN 20 kN D B C -3 m -3 m- -3 m- O+20KN-m -20KN-m O +25KN-m -25kN m

Q: If falling head permeability test is used for coarse grained soils, the cross-sectional are pipe sho...

A: If you use falling head method for coarse grained soil then small diameter tube will be emptied so r...

Q: 2. Draw the load and moment diagrams given the shear diagram as shown. Show all the values at differ...

A:

Q: Calculate the amount of lime and soda required to treat tuwo million litre (M.L.) of hard water, con...

A:

Q: D- Analyzing a system of forces acting on a concrete concrete slab shown in the picture is subject t...

A:

Q: A simply supported rectangular beam with a span of 7.2m has an effective depth, d = 430mm, and a wid...

A:

Q: A thin walled cylindrical pressure vessel having a radius of 0.5m and wall thickness of 25mm is subj...

A: Given data : Internal pressure (P)=700 KPa Radius (r)=0.5 m Wall thickness (t)=25 mm   To find : Hoo...

Q: Draw the FBD. Then, determine the reactions at A and B. 650 N 500 N 30°, 300 N 1500 N · m 60° B -3 m...

A:

Q: Classify the following 3 soils by the. šól člássification system. Sieve Analysis, % Finer No. 40 65 ...

A: Given-

Q: 40mm L-600mm P = 20kN 20mim

A:

Q: The segmented shaft shown below is made up of two shafts. Shaft (1) is a solid shaft with a diameter...

A: Given data: Solid shaft diameter =1.5" Hollow outside diameter =2.5" Hollow inside diameter =1.75" G...

Q: Problem: For the beam and loading shown, determine (a) the equation of the elastic curve, and (b) th...

A: Two support are given  Loading equation is given  Length of beam is given  And elastic curve equatio...

Q: e depth of the neutral axis of the final section in mm.0 Calculate the ultimate mo

A:

Q: How to know the if a reinforced concrete beam is a doubly reinforced beam?

A: To Determine Whether a beam is single reinforced or doubly reinforced ( Difference between them).

Q: 8 kN 5 kN/m A B V V (kN) 4 m m-+1 m-

A:

Q: A faucet is connected at the end of a pipe of roughness .00026. The pipe connected the faucet to the...

A: Given - Roughness = 0.00026 Pipe is connected to the water main, 40m away and 1.2m away. The pressur...

Q: A 10 million cubic yard levee was constructed by compacting soil to a total unit weight of 120 pcf, ...

A:

Q: Oil (SG = 0.86) is passing through a horizontal pipe whose diameter increases from 150mm diameter at...

A:

Q: 4. GNEH: watER 250 2m 44m SUめMERCED RECTAN GULAR SURPAOE OF WIDTH W = : (m

A:

Q: D 8' B 6' 8 E 8' 6' 30 kips C

A:

Q: 00 AT&T LTE 10:14 AM e* 49% a bbl-app.learn.fresnostate.edu 1 of 2 Determine the total change in len...

A:

Q: 1 of 2 Determine the average shear stress in the 20-mm diameter pin at A. |30 kN 5. 3 |B -2 m 4 m

A: Given data in question  Load  Dimensions  Diameter  To find out  Average shear stress

Q: Enumerate the steps in determining the ultimate moment strength of a singly-reinforced RC beam. Expl...

A:

Q: Problem: Draw the shear and moment diagram of the given beam. 100 kN B 75 kN - m 3 m- -3 m- -3 m- m-

A: Using section method to determine the shear force and moment at any section of beam. 

Q: The tangents of a simple curve have bearings of N 71°22’ E and S 76°45’ E respectively. A four-degre...

A: Given - The tangents of a simple curve have bearings of N 71°22’ E and S 76°45’ E respectively. A fo...

Q: NORMAI ES TIME ACTIVITY LS EF TF FF REMARKS 2 C E 1 8 5 H 4 J 10 K 1 M 5 N 10 R S 3

A: Given  Instructions to make network diagram. I am drawing activity or arrow diagram. Calculate  ES, ...

Q: type lf clay is used in the foundry industry

A: This question deals with the type of material(clay) used in foundry industry. So it comes under buil...

Q: A simply supported beam is carrying a uniform load. If the beam properties are given below, what is ...

A:

Q: 4) If the range of profitable demand for a company producing digital pumps was D'1 = 8.5 units and D...

A:

Q: 70kN 60KN 12KN/m 25KN.m. B C E A 6m 2m 2m 2m 21

A:

Q: -anmnlete this star my 5. Four forces (including the weight of the cylinder) are applied to a ring a...

A: This question is related to the Engineering Mechanics.

Q: 1. The frame shown in Fig. P-348 is supported in pivots at A and B. Each member weighs 5 kN/m. Compu...

A:

Q: 15KN/m 60KN 60KN 8kN/m 7m 3m 1m 3m 9m

A:

Q: Classify the following 3 soils by the AASHTO soil classification system. Sieve Analysis, % Finer No....

A: To Determine Classification of soil using AASHTO soil classification system. To Determine that in wh...

Q: Find degree of static indeterminacy

A:

Q: What are the definition of these symbols?

A:

Q: Determine the reactions at the support. 3 kN -2 m 2 kN 1.5 m 2 kN 1.5 m A Ax=4kN, Ay=4.5kN, By=4.5kN...

A:

Q: 5. A highway containing a crest vertical curve (equal tangent) has a posted speed limit of 50 mph. T...

A: Given data - Speed limit = 50 mph  The length of curve = 840 ft and at a distance of 3 + 51.00 stati...

Q: A field is in the form of a regular nonagon. The direction of the bounding sides was surveyed with a...

A:

Q: The hoist shown is used in a machine shop to position heavy workpieces in a lathe. If the cable betw...

A:

Q: .5 Prepare a set of profile leveling notes for the survey in Figure 2-34. In addition to comput- ing...

A: Prepare a set of profile leveling notes for the survey in Figure 2-34. In addition to comput ing all...

Q: A cantilever beam shown in the figure has a rectan gular cross section 300mm wide by h mm high.Find ...

A: The length of beam, L =12m6KN load is at free end and 3KN load is at 6m from free end.The width of b...

Q: • A concrete wall footing with a width of 0.9m and a depth of 0.6m supports a centrally placed 0.6-m...

A:

Q: If M=6kip.ft, determine the maximum tensile stress in the beam shown in the figure below

A: Moment intensity and cross section of I section have been given and it has been asked to determine s...

Q: If X-N(50,10), P(X > 65) = ? O 1) 0.067 O 2) 0.033 O 3) 0.168 O 4) 0.832

A: This represent the normally distributed variable with mean 50 and Standard deviation 10.

Q: How to determine the minimum and maximum steel ratios for an RC beam section?

A: To find maximum and minimum steel ratio in RC beam sections.  As per ACI CODE 318 steel ratios are d...

Q: 3. GIVEHI RECTANGULAR SUBMERGED BBJEA Of WワTH W> m 60°

A:

Q: w kN m 5m- 3m 5m-

A: RA + RB = 3 + 22x5  RA + RB = 113  Taking Moment about point A Rb x 8 = 3 x 5 + 22x5x10.5 Rb = 146.2...

Q: of 2 Determine the average shear stress in the 20-mm diameter pin at A. 30 kN 5 4 3 |B 2 m 4 m

A:

Q: Please calculate the clay content %, this w%

A: Given the table,  Sample number 1 2 3 Mass of empty, clean can (grams)  3.47 3.69 3.75 Mass o...

Q: y and 1.2 meters below. The p O Pa. If the flow rate when the at least .0126 m^3/s, what is th pipe?...

A:

Site Plan Requirements

A site plan (also known as a plot plan) is a diagram or process to show the proposed improvements on an existing property. A site plan is important, as it provides information regarding the landscape features of a given plot of land.  Zoning is done or can be understood with the help of a site plan.