31. ssm A copper kettle contains water at 24 °C. When the water is heated to its boiling point of 100.0 °C, the volume of the kettle expands by 1.2 × 10-³ m². Determine the volume of the kettle at 24 °C.

31. ssm A copper kettle contains water at 24 °C. When the water is heated to its boiling point of 100.0 °C, the volume of the kettle expands by 1.2 × 10-³ m². Determine the volume of the kettle at 24 °C.

Physics for Scientists and Engineers, Technology Update (No access codes included)

9th Edition

ISBN:9781305116399

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter20: The First Law Of Thermodynamics

Section: Chapter Questions

Problem 20.55P: A bar of gold (Au) is in thermal contact with a bar of silver (Ag) of the same length and area (Fig....

See similar textbooks

Similar questions

In 1993, the U.S. government instituted a requirement that all room air conditioners sold in the United States must have an energy efficiency ratio (EER) of 10 or higher. The EER is defined as the ratio of the cooling capacity of the air conditioner, measured in British thermal units per hour, or Btu/h, to its electrical power requirement in watts. (a) Convert the EER of 10.0 to dimensionless form, using the conversion 1 Btu = 1 055 J. (b) What is the appropriate name for this dimensionless quantity? (c) In the 1970s, it was common to find room air conditioners with EERs of 5 or lower. State how the operating costs compare for 10 000-Btu/h air conditioners with EERs of 5.00 and 10.0. Assume each air conditioner operates for 1 500 h during the summer in a city where electricity costs 17.0 per kWh.
A bar of gold (Au) is in thermal contact with a bar of silver (Ag) of the same length and area (Fig. P20.55). One end of the compound bar is maintained at 80.0C, and the opposite end is at 30.0C. When the energy transfer reaches steady state, what is the temperature at the junction?
A perfectly insulating cylindrical glass is partially full of water. At the top of the water is a uniform layer of ice. The temperature of the water is 0 ∘C,0 ∘C, and the temperature of the air above the ice is held fixed at −19.00 ∘C.−19.00 ∘C. If the initial thickness of the ice layer is ?i=0.0950 m and the depth of the water below the ice is ?w=0.1050 m, how long, in hours, will it take for the rest of the water to freeze? Assume that there is no transfer of heat through the sides or bottom of the glass and that the ice layer can slide freely up and down the glass. The latent heat of fusion of water is 3.33×105 J/kg, and the thermal conductivity of ice is 2.180 W/(m⋅∘C). The density of water near freezing is 1000.0 kg/m3, and the density of ice is 917.00 kg/m3.
(III) Approximately how long should it take 8.2 kg of ice at 0°C to melt when it is placed in a carefully sealed Styrofoam ice chest of dimensions 25cmx 35cm x55 cm whose walls are 1.5 cm thick? Assume that the conductivity of Styrofoam is double that of air and that the outside temperature is 34°C.
A copper telephone wire has essentially no sag between poles 36.0 m apart on a winter day when the temperature is −20.0°C. How much longer is the wire on a summer day when the temperature is 38.0°C? Material: Cooper Average linear Expansion coefficient (x)(celsius degree): 17x10^-6
The outer diameter of a glass jar and the inner diameter of its iron lid are both 760 mm at room temperature (20.0 ∘C). a)What will be the size of the mismatch between the lid and the jar if the lid is briefly held under hot water until its temperature rises to 57.5 ∘C, without changing the temperature of the glass? Use the coefficient of linear expansion for iron α=1.2×10−5K−1.
A bimetallic strip of total thickness x is straight at temperature T. What is the radius of curvature of the strip, R, when it is heated to temperature T + DT? The coefficients of linear expansion of the two metals are a1 and a2, respectively, with a2 > a1. You may assume that each metal has thickness x/2, and you may assume that x << R.
A brass ring of diameter 10.00 cm at 20.00C is heated and slipped over an aluminum rod of diameter 10.01 cm at 20.00C. Assuming the average coefficients of thermal expansion are constant for brass and aluminum, (a) to what temperature must this combination be cooled to separate them? Is this attainable? (b) What if the aluminum rod is 10.02 cm in diameter
A 1.0-m-long steel beam, initially at a temperature of 250 C, increases in temperature to 1000 C by inserting it into an insulating jacket for several minutes while the inside of the jacket is subsequently flooded with steam. By how much does the length of the steel beam expand? (The thermal coefficient of linear expansion for steel is 12 x 10-6 (C0)-1) a. 0.90 mm b. 1.0 mm c. 0.70 mm d. 0.80 mm e. 0.60 mm
A spherical steel ball bearing has a diameter of 2.540 cm at 26.00°C. (Assume the coefficient of linear expansion of the steel is 1.10 10-5(°C-1), and the average volume expansion coefficient is 3.30 10-5(°C-1).) A) What is its diameter when its temperature is raised to 97.0°C? (Give your answer to four significant figures in cm.) B) What temperature change is required to increase its volume by 1.100%?
Thank u! A steel sphere with radius 1.0010 cm at 34.0°C must slip through a brass ring that has an internal radius of 1.0000 cm at the same temperature. To what temperature must the brass ring be heated so that the sphere, still at 34.0°C, can just slip through? Coefficient of linear expansion a for brass is 19.0 x 10^-6 K^-1
A spherical steel ball bearing has a diameter of 2.540 cm at 30.00°C. (Assume the coefficient of linear expansion for steel is (11 ✕ 10−6 )(°C)−1. (a) What is its diameter when its temperature is raised to 102.0°C? (Give your answer to at least four significant figures.) cm (b) What temperature change is required to increase its volume by 1.100%?