3–19. The tongs are used to grip the ends of the drillingpipe P. If a torque (moment) of Mp = 1200 N · m is neededat P to turn the pipe, determine the cable force F that mustbe applied to the tongs. Set 0 = 30°.150 mmMp1075 mm

Answered: 3–19. The tongs are used to grip the…

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.5.10P: Solve the preceding problem (W 250 × 44.8) if the resultant force P equals 110 kN and E = 200 GPa.

See similar textbooks

Similar questions

Determine the intensity and position of the resultant R lf two forces F1 and F3 and torque M that acts on the metal profile given as in the figure,if: F1= 2kN a=2,10m F2= 5kN b=2,10m M=24kNm c=3,10m
How much work is done by the force in the spring when the slender rod rotates clockwise about the fixed pin support at O from the vertical position (where AB is horizontal) to the horizontal position? The spring has a stiffness of k = 125 N/m and an unstretched length of 0.15 m. Take d1= 0.29 m and d2= 0.85 m. Choose the correct answer. a) 94.9 Joule b) 99.9 Joule c) -99.9 Joule d) 0 Joule e) -94.9 Joule
The lever is held to the fixed shaft using the pin AB. If the couple is applied to the lever, determine the shear force in the pin between the pin and the lever.
The railcar docklight is supported by the 1 8-in.-diameter pin at A. If the lamp weighs 4 lb, and the extension arm AB has a weight of 0.5 lb>ft, determine the average shear stress in the pin needed to support the lamp. Hint: The shear force in the pin is caused by the couple moment required for equilibrium at A.
2a. If the load intensities w1=82 N/m, w2=176 N/m, and w3=102 N/m, determine the total moment (in N*m) caused by all these applied distributed forces about point A. Take counterclockwise as positive. Answer must include 1 place after the decimal point. 2c. Find out all of the support reactions components if applicable.
The motorcycle weighs 151 kg and the driver weighs 64 kg. Dimensions l1 = 0,31 m ja l2 = 0,23 m Determine the support force on the rear tire.
Find the force F that must be applied at the handle to produce a clamping force of 75 lbs at E, given:L1 = 8 in, L2 = 2.25 in, L3 = 1 in, L4 = 10 in, θ = 30 °
the bar supported by a pin at a and a cable at b carries a load of 260 nat c. neglecting the weight of the bar, a.) determine the normal force 3 m from a. b.) determine the shear force 3 m from a c) determine the bending moment 3 m from a d.) determine the torsion 3 m from a 605 b 5 m 4m 12 260 n
The bent rod is supported at points A, B and C by smooth journal bearings, and is subjected to force F. If dimensions a = 2.3 m, b = 1.5 m, c = 0.6 m, and d = 2.5 m, and the force F is {-2i + 9j - 3k} kN, determine the magnitude of the moment (in kN⋅m) caused by force F about point A. Answer must include 2 places after the decimal point.
The system is made up of a bar, supported by a pin at point A and by a smooth collar at point B (the collar slides on the ABG bar). The collar is pinned to bar BDE, and bar BDE is supported by a pin at D and a cable at end E. Determine the force P such that the force in the cable equals to T. With T= 26 lb, a=4 in, b=9 in
The copper pipe has an outer diameter of 40 mm and an inner diameter of 37 mm. If it is tightly secured to the wall and three torques are applied to it, determine the absolute maximum shear stress developed in the pipe.
Which of the following gives the moment MD about point D of the tensile force TBA exerted by the wire at point B? Note that rB/D = (4i - 6k) m and TBA = (-8i + 6j + 4k) kN and that MD = rB/D x TBA. a. (36.0i + 32.0j + 24.0k) kN-mb. (48.0i + 24.0j + 16.0k) kN-mc. (-36.0i - 32.0j - 24.0k) kN-md. (16.0i - 12.0j -8.0k) kN-m

SEE MORE QUESTIONS

Recommended textbooks for you

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

3–19. The tongs are used to grip the ends of the drilling pipe P. If a torque (moment) of Mp = 1200 N · m is needed at P to turn the pipe, determine the cable force F that must be applied to the tongs. Set 0 = 30°. 150 mm Mp 1075 mm