1.34 Estimate the tensile strength required to prevent cracking in a concrete-likematerial that is cast into a bar, 50 in. long, and is fully restrained at each endagainst axial movement. The concrete is initially cast and cured at a temperatureof 100°F and subsequently cools to a temperature of 0°F. Assume the modulus ofelasticity is 5 million psi and the thermal coefficient is 5 x 10-6 in./in./°F.

Answered: 34 Estimate the tensile strength…

Solid Waste Engineering

3rd Edition

ISBN:9781305635203

Author:Worrell, William A.

Publisher:Worrell, William A.

Chapter5: Separation Processes

Section: Chapter Questions

Problem 5.33P: According to Figure 5-20, is ii possible to completely separate one of the four materials from the...

See similar textbooks

Similar questions

Estimate the tensile strength required to prevent cracking in a concretelike material that is cast into a bar, 1.25 m long, and is fully restrained ateach end against axial movement. The concrete is initially cast and curedat a temperature of 40°C and subsequently cools to a temperature of –20°C.Assume that the modulus of elasticity is 35 GPa and the thermal coefficient is9 X 10-6m/m/°C.
A concrete has a height of 5 meters and has unit area of 3 m3 supports a mass of 30, 000 kg. Determine the following: Stress Strain Change in height Acceleration due to gravity (g) = 10 m/s2 Young modulus of concrete = 20x109N/m2
Estimate the tensile strength required to prevent cracking in a concretelike material that is cast into a bar, 1.25 m long, and is fully restrained at each end against axial movement. The concrete is initially cast and cured at a temperature of 40°C and subsequently cools to a temperature of -20°C. Assume that the modulus of elasticity is 35 GPa and the thermal coefficient is 9 * 10-6 in./in./°C.
Assume the temperature of your skin is 32o If you touch a thick piece of aluminum at 75oC, what is the skin surface temperature? How about a block of concrete at 90oC? Look up the properties for the any two materials . Discuss the results by comparing the two cases.
Estimate the tensile strength required to prevent cracking in a concrete-like material that is cast into a bar, 50 in. long, and is fully restrained at each end against axial movement. The concrete is initially cast and cured at a temperature of 100°F and subsequently cools to a temperature of 0°F. Assumethat the modulus of elasticity is 5 million psi and the thermal coefficient is 5 * 10-6 in./in./°F.
why do we need to know the Specific Gravity and Absorption of Fine Aggregate, Surface Moisture of Fine Aggregate, and how it is important in concrete
Please answer. Thank you! Concrete has a coefficient of linear expansion of 12x10-6 /0 C and considering a large concrete structure and typical temperatures during summer and cold seasons. a. Will there be a change in concrete’s linear size between summer and cold seasons? Explain your answer. b. If there is a change in its linear size, how would this change be accommodated?
A concrete test cylinder is 150mm in diameter and 300mm in length. During an axial compression test the diameter increased by 0.1399 mm and the length decreased by 0.397 mm. The concrete has an ultimate compressive strength of 21Mpa, Ec=20,000Mpa. Compute the compressive load that caused the above deformations
Q-civil Concrete formwork Ata temperature of 50°F, 150 lb per cu ft of concrete is poured into a 14-foot-tall column form. Since there is no retarder, the concrete is Type I. Concrete will be poured to a depth of less than 4 feet with typical internal vibration. The placement speed is 7 feet per hour.
A concrete-like material that is cast into a bar is fully restrained at each end against axial movement. The concrete is initially cast and cured at a temperature of 100 °F and subsequently cools to a temperatureof 0 °F. Assuming the modulus of elasticity is 5 million psi and the thermal coefficient is 5 x 10^-6 in./in./°F., calculate the minimum TENSILE STRENGTH required to prevent it from cracking.
Determine the safe wall thickness of a 35 inches steel tank with internal pressure of 8.02 Mpa. The yield stress of material is at 300 Mpa. The factor of safety to use is 2.5. d. 21.6 mm c. 28.4 mm b. 26.8 mm a. 29.7 mm
The concrete shape is formed by rotating the shaded area about the y axis. Determine the moment of inertia Iy. The specific weight of concrete is γ = 150 lb/ft3.

SEE MORE QUESTIONS

Recommended textbooks for you

Solid Waste Engineering

Civil Engineering

ISBN:

9781305635203

Author:

Worrell, William A.

Publisher:

Cengage Learning,

Solid Waste Engineering

Civil Engineering

ISBN:

9781305635203

Author:

Worrell, William A.

Publisher:

Cengage Learning,

SEE MORE TEXTBOOKS