3/4" roller chain is to transmit power from a 17-tooth drive sprocket to 43-tooth sprocket. Centers of the sprockets are 16 inches apart. An idler sprocket is placed on the slack side of the chain, thereby increasing the number of teeth in contact with the sprocket at any time to 10 and 28 for the drive and driven sprockets, respectively. Estimate the arc of contact of the chain with large sprocket

3/4" roller chain is to transmit power from a 17-tooth drive sprocket to 43-tooth sprocket. Centers of the sprockets are 16 inches apart. An idler sprocket is placed on the slack side of the chain, thereby increasing the number of teeth in contact with the sprocket at any time to 10 and 28 for the drive and driven sprockets, respectively. Estimate the arc of contact of the chain with large sprocket

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter4: Numerical Analysis Of Heat Conduction

Section: Chapter Questions

Problem 4.49P

See similar textbooks

Similar questions

A pulley 600 mm. in diameter transmits 40 kW at 500 rpm. The arc of contact between the belt and pulley is 144° having a center distance of 1100 mm. Determine: (a) diameter of the driven pulley for open belt drive, (b) speed of the driven pulley, and (c) belt length for open belt connection.
A mini motorcycle is driven by a combustion engine with mechanical transmission. The 12Hp motor spins at a speed of 1150 rpm. The motorcycle runs at a linear speed of 45 km/h on 12-inch wheels. Preliminary center to center distance is 13”. This type of motorcycle requires two strands (conical double sleeve assembly) and is subjected to hard shocks. a) Calculate the effective power.b) Choice of chain and sprocket. (Standard part number, see catalog)c) Calculate the speed ratio. https://pdf.directindustry.com/pdf/martin-sprocket-gear/general-catalog/9091-246439.html
A mini motorcycle is driven by a combustion engine with mechanical transmission. The 12Hp motor spins at a speed of 1150 rpm. The motorcycle runs at a linear speed of 45 km/h on 12-inch wheels. Preliminary center to center distance is 13”. This type of motorcycle requires two strands (conical double sleeve assembly) and is subjected to hard shocks. Can I get a detailed explanation for Choice of chain and sprocket. (Standard part number, see catalog) https://pdf.directindustry.com/pdf/martin-sprocket-gear/general-catalog/9091-246439.html
A belt drive is used to transmit power from an electric motor to a compressor for a refrigerated truck. The compressor must still operate when the truck is parked and the engine is not running. The 50-hp electric motor is rated at 150+X rpm (where value of X = 50), and the motor sheave diameter is 5+d1 in. (where value of d1 = 5). The compressor sheave has 8+d2 in (where value of d2 = 5) diameter. The center distance of the drive is 15 in. Determine the appropriate industrial V belt size, the length of belt, operating speed of compressor and belt speed.
A shaft is supported by two bearings placed 1.2 m apart. A pulley of diameter Dc meter is mounted at a distance of 300 mm to the right of left hand bearing and this drives a pulley directly below it with the help of belt having maximum tension of 2.25 kN. Another pulley of diameter Dd meter is placed 200 mm to the left of right hand bearing and is driven with the help of electric motor and belt, which is placed horizontally to the right. The angle of contact for both the pulleys is 180° and μ = 0.24. Determine the suitable diameter for a solid shaft, allowing working stress of 63 MPa in tension and 42 MPa in shear for the material of shaft. Assume that the torque on one pulley is equal to that on the other pulley. Dc in mm = 575Dd in mm = 475
A solid shaft of 200 mm diameter has the same cross sectional area as that of a hollow shaft of the same material with the inside diameter of 150 mm. Find the ratio of the power transmitted by the two shafts at the same speed. Show necessary figure and all calculations involved
A single-strand roller chain drive connects a 50-hp engine to a lawn waste chipper/shredder, as shown below. As the engine operates at 1000 rpm, the shredding teeth should rotate at 250 rpm. The driven sprocket has 60 teeth. Determine the chain speed.
1. A pulley 580 mm in diameter transmits 60 kW at 650 1pm by means of belt. Determine the effective belt pull.2. Find the angle of contact on the small pulley for a belt drive with center distance of 75 in. if pulley diameters are 9 in and 18 m, respectively.
A chain drive is desired to couple a gearmotor with a bucket elevator. The 40 hp. gearmotor will operate at 350 rpm and the elevator drive shaft must operate as close to 60 rpm as possible. Select an appropriate chain size, commercially available sprockets, and number of links for a chain. Also calculate the actual chain speed and the center distance.
In the Scottish Yoke mechanism in the figure, r = 63 cm, φ = 23 °, β = 116 ° and e = 34 cm are given. Accordingly, find the velocity of the S3 output since the angular velocity of the actuating limb is θ = 0.14 rad / s. Partial scoring; S3 50% in cm
a) A line shaft as shown in Figure Q is driven using a motor placed vertically below it. The pulley on the line shaft is 1.6 m in diameter and has belt tensions 7.5 kN and 2.4 kN on the tight side and slack side of the belt respectively. Both tensions may be assumed to be vertical and the weight of the pulley is negligible. If the pulley is overhang from the shaft, the distance of the centre line of the pulley from the centre line of the bearing being 500 mm.6.Figure Q(i) Predict using distortion energy theory, the appropriate diameter of the shaft that failure will not occur if the yield strength, Sy = 370 Mpa and factor of safety is 2.5. (ii) Assuming the maximum allowable shear stress of 42 MPa, find its diameter using maximum shear stress theory. (iii) Comparing the diameters in (i) and (iii) above, which of them would you have used to design your shaft and why?
In double hook joint, the angle of the driving and of the driven shaft with the intermediate shaft is 30°. The max ratio of the driven shaft to driving shaft angular velocities is (a) 3/4 (b) 4/3 (c) 1/2 (d) 1/4