The chain binder is used to secure loads of logs, lumber, pipe, and the like. If the tension T₁ is 3.1 kN when = 30°, determine the force P required on the lever and the corresponding tension T₂ for this position. Assume that the surface under A is perfectly smooth. Assume a = 100 mm, b = 420 mm.

The chain binder is used to secure loads of logs, lumber, pipe, and the like. If the tension T₁ is 3.1 kN when = 30°, determine the force P required on the lever and the corresponding tension T₂ for this position. Assume that the surface under A is perfectly smooth. Assume a = 100 mm, b = 420 mm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The metal strap has a thickness t and width w and is subjected to a temperature gradient T1 to T2 (T1 6 T2). This causes the modulus of elasticity for the material to vary linearly from E1 at the top to a smaller amount E2 at the bottom. As a result, for any vertical position y, measured from the top surface, E = [(E2 - E1)>w]y + E1. Determine the position d where the axial force P must be applied so that the bar stretches uniformly over its cross-section. w
The collar C is fixed to rod AB using a glued bond that allows a maximum force of 405 N parallel to the axis of the rod. The collar has weight W acting in the negative z direction. Determine the weight W in N of the collar that will cause the glued bond to break as shown in figure.
The spring has a stiffness of 830 N/m and is undisturbed and measures 400 mm. Determine the forces on the BC and BD cables when the spring is stretched in the position shown in the figure.
A man holds a 35-kg ladder in his hands perpendicular to his hands (Figure 6). The free body diagram is shown on the right. If the maximum compressive force the person can withstand is 400N, determine:a) The minimum value of θ so that the person is able to hold the ladder.b) The compressive force at the end of the ladder at that time
How is 89.4 N obtained as the reaction at support C (See 2nd attached image) in this problem: Neglecting friction, determine the tension in cable ABD and the reaction at support C & the angle it makes w/ member AE.
The system is made up of a bar, supported by a pin at point A and by a smooth collar at point B (the collar slides on the ABG bar). The collar is pinned to bar BDE, and bar BDE is supported by a pin at D and a cable at end E. Determine the force P such that the force in the cable equals to T. With T= 26 lb, a=4 in, b=9 in
If d=4ft, determine the force in cable AB, AC, and AD needed to support the 3500lb platform.
The Cylinder weighs 1000 kg, rest on an plane which is inclined at 34° from the horizontal. The normal force acting on a plane to the cylinder is 10 KN. Assume smooth surface, the cylinder leaned to a vertical rod of 8m long and has a weight of 5 KN which was supported by a cable and a hinged (as shown). Find the tensile force of the cable holding the rod and the reactions of hinged to support the cylinder from sliding.
If the weight of the h0m0gen0us cylinder in equilibrium is 750N, what is the magnitude (N) of the n0rmal f0rce if the surface is r0ugh?
The post is made of Douglas fir and has a diameter of 100 mm. If it is subjected to the load of 20 kN and the soil provides a frictional resistance that is distributed along its length and varies linearly from w = 4 kN>m at y = 0 to w = 12 kN>m at y = 2 m, determine the force F at its bottom needed for equilibrium. Also, what is the displacement of the top of the post A with respect to its bottom B? Neglect the weight of the post.
hey may you please help me here 1) Determine the magnitude of the horizontal and vertical components of the reaction force at the pin connection A in newtons.
Determine the tensile force of the rope.