36.A 1000-kVA, 11-kV three-phase wye-connected synchronous generator supplies a 600-kW, 0.8 leading of load. The synchronous reactance is 24 Ω per phase and the armature resistance is negligible. Calculate the voltage regulation.

36.A 1000-kVA, 11-kV three-phase wye-connected synchronous generator supplies a 600-kW, 0.8 leading of load. The synchronous reactance is 24 Ω per phase and the armature resistance is negligible. Calculate the voltage regulation.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.5P

See similar textbooks

Related questions

Q: .For the following voltage and current phasors, calculate the apparent power in VA V = 122 < 15⁰…

A: Given,The voltage phasor value is,V=122∠15° VrmsThe current phasor value is,I=18∠46° Arms

Q: Q2.Find Q-point when VBB = 1V, 2 V and 3 V.. Assume VCE(sat) = 0 V. Re 1.0 K 10 V +4/+ H1₁ www 20 KQ…

Q: Q1: Using a 50 nF capacitor in the parallel RLC bandpass filter with a quality factor of 5 and a…

A: We need to analyse the parallel RLC circuit .

Q: The received power and noise power measured at a receiver is 0.5 mW and 150 nW, respectively.…

Q: 4.20 Calculate the inductive reactance in N/km of a bundled 500-kV, 60-Hz, three-phase completely…

A: Given A overhead line with parameters, we need to determine the inductive reactance. Please find…

Q: 外的 Si 7mA 22.2k2 *1.2 Q os

Q: A) RTOTAL = B) I TOTAL = VTOTAL = R67 = E) V₂ 11

Q: Determine Vx in this circuit using Thevenin theorem. Draw illustrations if needed. Show complete…

Q: Solve index of modulation and Sketch each in "TIME DOMAIN a. Em= 5V; Ec=10V; m=? b. Em-10V; Ec-10V;…

Q: 120V, 60H₂, 30, 6 Pole, Y-connected IM R₁ = 0.08₁ X₁ = 0.3 S = 0,03 XM = 6.33 R2=007, X₂ = 0.3…

Q: A/Find the Norton equivalent circuit around R₁

Q: Q/ For the following signal, replote the signal with the following conditions. X(X) = { 2 5t-3 => 1…

A: Given A signal x(t),we need to plot it and replot for its time shifting versions. Please find the…

Q: Refer to the figure below and calculate the readings on the two wattmeters. Use VBA as reference…

A: Two wattmeter method:- Two wattmeter method is used for 3-phase 3wire star or delta connection.…

Q: Q2- In the circuit in fig.(2) if 13= 1mA . Find all currents (11, 12, 14 and 15) and the voltage…

A: In this question we need to find all current and supply voltage

Q: Electrical Engineering --question 1-- Calculate the theoretical voltages across the resistor and…

Q: Q1. Determine IE, VBE, VCE, and VCB in the circuit. Assume BDC = 150. Rc 390 RB 8V 38 Assume VCE(-…

A: We need to find out the current and voltage for given circuit

Q: Q1: Find the Ceg. At point A&B in the network in fig.(1) Luf 41 E 10 TIME Fig.1 TIME

Q: Q2.Find Q-point when VBB = 1V, 2 V and 3 V.. Assume VCE(sat) = 0 V. Re LOKO RB www Bpc = 50 20 KQ…

A: Given

Q: Determine the power absorbed by each of the resistors in the circuit shown in Fig.(3). 12 v ܤ ܚܕ ܟ ܕ…

A: Given the circuit with the voltage and current source.

Q: 120/0° rms 120/120⁰ rms ||- La I₂₁ 120-120° rms Iz b B 12₂ 10 Ω ele J552 N -/10 02 C

A: Line current: It is the time rate of the change of the charges. It flows from high voltage to low…

Q: Use Millman’s theorem and determine the magnitude of the neutral displacement voltage,(Vsn) in the…

A: The Given data is Za=0°18ΩZb=60°12ΩZc=60°30ΩEab=360VVsn=?

Q: II. In a 220 Vrms, 60 Hz. Source, determine the following values: a) Trigonometric equation b) V…

Q: The sensitivity of a PMMC instrument is 10k /V. If this instrument is used in a rectifier type…

A: Given, For a PMMC instrument Sensitivity, Sdc = 10 kΩV

Q: Define Shift register and draw four-bit shift register using D-Flipflop.

A: Since these are two different questions, in the following section, the first question will be…

Q: Q2- In the circuit in fig.(2) if 13= 1mA . Find all currents (11, 12, 14 and 15) and the voltage…

Q: Q1. Determine IE, VBE, VCE, and VCB in the circuit. Assume BDC = 150. Rc 390 RB wwww. w 8V 88 Assume…

Q: Q1J using a sonf capacitor in the Parattet RLC bandpass filter with a quality factor of 5 and a…

Q: .Determine IE, VBE, VCE, and VCB in the circuit. Assume BDC = 150.

Q: In a balanced three-phase Y-Y system, the source is an abc sequence of voltages and Van = 148∠8°…

Q: Find current through R2 resistor. R1 R3 10 12 II +vi 10 Select one: O a. 3.04 h 267 NO (+1

A: current in R2 is determine by using simple nodal analysis it is given as-

Q: 1. Find Ix in the circuit of figure shown below using Kirchhoff's law and Maxwell Analysis. 10 Q2 1…

A: To find ix in the given circuit using kirchoff's law and Maxwell analysis

Q: Mage

A: Given AM wave form is shown below. a. From the above figure The maximum voltage of a signal is…

Q: In a 50 hertz circuit, containing a 10 microfarad capacitor, the capacitive reactance is Select the…

Q: An air-filled coaxial line with e=₁ and µ-u, has a line inductance L'=(1/54)µH/m. What is the line…

A: We need to find out the capacitance of co axial cable

Q: Q1. If vs= 50 cos(4t). Find i and vi 8 Ω ΤΩ 3Η F

Q: A 230-V, 50-Hz,40 HP induction motor has power factor of 0.8 (lagging). Three A-connected capacitors…

Q: Problem 4: Design a sequential circuit with the finite state machine shown in Table 2, using D…

Q: If Vab = 221 Vrms in a balanced Y-connected three-phase generator, find the magnitude of the phase-a…

Q: Q1. Determine IE, VBE, VCE, and VCB in the circuit. Assume BDC = 150.

Q: R₁=56 20v A) RTOTAL = B) I TOTAL CV-TOTAL = R67 E) V3 R3-20 R₂=55 R5=45 R6 = 3 R4=25 R7 = 3

Q: Q2 A series RLC bandreject filter is used to reject a 200 Hz sinusoid while passing other…

Q: Briefly explain the working of following power plants a) Thermal Power plant b) Hydel power plant

A: Thermal power plant: The plant that produces electrical energy by the use of the coal as a…

Q: The load shown below is connected to a 360 V, 50 Hz three-phase supply with a positive phase…

A: The load shown below is connected to a 360 V, 50 Hz three-phase supply with a positive phase…

Q: The voltage of a source is e = 220 cos (wt - 1200) while its three loads take currents given by…

A: A closed path, where electric current can flow defined as an electric circuit. It is various…

Q: Q \ Compare between Repulsion motor and Compensated Repulsion motor and Repulsion start induction…

A: Repulsion motor : A motor is a device which converts electrical input into mechanical output is…

Q: Q4: Find Vx in the network in fig.(4) using mesh (loop) analysis. 12^ M m 30v vx=4r {4^ Fig.4 Elon…

Q: Under some conditions, it is possible to approximate the effects of ferromagnetic materials by…

A: Given Few parameters of cylindrical wire,we need to determine magnetic field, magnetic field…

Q: B-When the number of poles of a low pass filter circuit is increased, the a. frequency response…

A: when the number of poles of low pass filter circuit is increased then the root locus of low pass…

Q: A two-port is described by the following equations: V1 = 50I1 + 10I2 and V2 = 30I1 + 20I2. Which of…

Q: explain the aliasing in the PAM Signal?

A: The analog pulse modulation techniques are classified into three types, which are mentioned as…

Concept explainers

Winding and Constructions

Alternating Current (AC) winding is generally of the 3-phase type due to the inherent advantages of the 3-phase machine. Armature coils must be connected to the yield balance (equivalent in magnitude and 2/3 of the series phase difference of the rod) 3-phase electromotive forces (emf). The armature should be divided into step-bands to start with slots around the perimeter.In the construction of AC machines, the frame is used as an external protective shield to protect it from environmental conditions. The frame also serves as the outer perimeter, allowing the interior to be easily placed. The static state section of the devices is the stator winding attached stator.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3 Final Answer

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Winding and Construction of the Rotor and Stator

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

3-phase,50 Hz, delta connected generator, its stator winding having 12sninai ns pole pair and 6 conductors in each, if the total air gap flux is 160mwb. Find the terminal voltage. The prime mover speed is 750rpm.
Consider a three-phase 13.8 kV, 25-MVA, Y-connected synchronous generator whose three-phase short-circuit losses are 52.8 kW at rated armature current. Calculate its armature resistance per phase. a-0.16 Ohm b-0.016 Ohm -1.016 Ohm: d- 603.2 A e-0.7 Ohm.
A three-phase wye-connected wound rotor synchronous generator rated at 10 KVA, 230 v has synchronous reactance of 1.2 ohms per phase and armature resistance of 0.5 ohm per phase. What is the power factor such that the voltage regulation at full-load is zero?
A three-phase, 250 MVA, 16 kV rated synchronous generator is feeding into an infinite bus bar at 15 kV. The generator has a synchronous reactance of 1.62 pu. It is found that the machine excitation and mechanical power input are adjusted to give E = 24 kV and power angle δ = 30◦. a) Determine the line current and active and reactive power fed to the generator terminal. b) The mechanical power input to the generator is increased by 20% from that in part (a) but its excitation is not changed. Find the new line current and power factor. c) With reference to part (a) current is to be reduced by 20% at the same power factor by adjusting mechanical power input to the generator and its excitation. Determine E, angle δand mechanical power input.
A three-phase, 250 MVA, 16 kV rated synchronous generator is feeding into an infinite bus bar at 15 kV. The generator has a synchronous reactance of 1.62 pu. It is found that the machine excitation and mechanical power input are adjusted to give E = 24 kV and power angle δ = 30 degree. a) Determine the line current and active and reactive power fed to the generator terminal. b) The mechanical power input to the generator is increased by 20% from that in part (a) but its excitation is not changed. Find the new line current and power factor. c) With reference to part (a) current is to be reduced by 20% at the same power factor by adjusting mechanical power input to the generator and its excitation. Determine E, angle δ and mechanical power input. d) With the reduced current as in part (c), the power is to be delivered to generator terminal at unity power factor, what are the corresponding values of E and δ and also the mechanical power input to the generator. Per-unit values are given on…
A 3-phase, Y-connected, 60 Hz, 6 MVA, 13.2kV synchronous generator has a synchronous reactance of 0.9 ohms and negligible resistance. It supplies a constant power load at rated conditions at 0.83 pf lagging. At the load, the line current lags the line-to-neutral voltage by how many degrees?
The effective resistance of a 2200 V, 50 Hz, 440 KVA, 1 -phase alternator is 0.5 ohm. On short-circuit, a field current of 40 A gives the full load current of 200 AS. The electromotive force on open-circuits with same field excitation is 1160 V. Then the synchronous impedance and reactance is _______ ohm and _______ ohm respectively.
A 4-pole, 36-slot, 60-Hz, three-phase, Y-connected, synchronous generatorhas 10 turns per coil. The flux per pole is 50 mWb. For a series connection,determine (a) the synchronous speed, (b) the per-phase voltage, and (c) theline voltage
A 3-Phase 10Kva, 400 V, 50Hz star connected alternator supplies a rated load at 0.8 power factor lagging. If the armature resistance per phase is 0.5Ჲ and the synchronous reactance is 10Ჲ, using the e.m.f method, estimate the alternator’s voltage regulation
A3 phase , 15 kV, 60 Hz, 30 MVA, Y-connected cylindrical-rotor synchronous machine generator has Ra =0.5 Ω per phase and Xs =5.2 Ω per phase. The generator delivers the rated load at 15 kV and 0.85 lagging power factor. Determine the excitation voltage, Ef, for this operating condition.
A 3 phase, wye connected wound rotor synchronous generator rated at 10 kVA, 230V has a synchronous reactance of 1.2 ohms/phase and an armature resistance of 0.5ohm/phase. What is the % voltage regulation at full-load with 85% laggingpower factor?
3-phase,50 Hz, delta connected generator, its stator winding having 12 slots per pole pair and 6 conductors in each, if the total air gap flux is 160mwb. Find the terminal voltage. The prime mover speed is 750rpm.