4.20 Calculate the inductive reactance in N/km of a bundled 500-kV, 60-Hz, three-phase completely transposed overhead line having three ACSR 11/13 kcmil conductors per bundle, with 0.5 m between conductors in the bundle. The horizontal phase spacings between bundle centers are 10, 10, and 20 m.

4.20 Calculate the inductive reactance in N/km of a bundled 500-kV, 60-Hz, three-phase completely transposed overhead line having three ACSR 11/13 kcmil conductors per bundle, with 0.5 m between conductors in the bundle. The horizontal phase spacings between bundle centers are 10, 10, and 20 m.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.20P: Calculate the inductive reactance in /km of a bundled 500-kV, 60-Hz, three-phase completely...

See similar textbooks

Related questions

Q: A wire carrying 31 A current passes between the poles of a strong magnet that is directed at angle…

Q: A capacitor of capacitance 120 µF is connected across a 220 V, 60 Hz A.C. mains. Calculate the value…

A: 22)

Q: A wire carrying 31 A current passes between the poles of a strong magnet that is directed at angle…

A: When ever a current carrying conductor placed in magnetic field , it will experience a force on it.…

Q: Qy A Transistor dissipates 50w in ambient temperature of fo, The thermal visistance are 8jc=0 · 5…

A: Pavg= Average rate of heat generated of a transistorTJ= Junction TemperatureTC= Case…

Q: The neutral current

Q: A 30 synchronous machine has the following parameters: X₁-0.9 pu, X,-0.65 pu The field current of…

A: Given Xd =0.9 pu Xq =0.65 pu Open circuit voltage Vt=1 pu Machine is synchronized to infinite bus…

Q: Q1. Construct the Mealy and Moore state diagrams for a sequence detector that outputs a 1 when the…

A: A Binary sequence detector is a circuit implemented using combinational and sequential circuit…

Q: Q1. Determine IE, VBE, VCE, and VCB in the circuit. Assume BDC = 150.

Q: Q3: Find Req. between points (A&B) in the network in fig.(3). 2 lon $82 Fig.3 36r

Q: Discuss the difference between Passive and Active Components? Give examples

A: Basis Active components passive components 1. Nature of source Active components deliver power or…

Q: iven the asynchronous circuit, determine the map Q1, Q2, Z, transition table, and flow table.

A: Given Asynchronous circuit is shown below.

Q: Given a Voltage Divider Bias Common Emitter amplifier with the following data: R₁ = 82 kN, R2= 22…

Q: The load current in a system is 100 A. The short-circuit current for the smallest fault is 1000 A.…

A: Given that; Load Current=100ASmallest fault current=1000ARelay current IR=5A

Q: Q1.Determine IE, VBE, VCE, and VCB in the circuit. Assume BDC = 150.

Q: why is FM less prone to noise as compared to AM?

Q: 04: Calculate the R.M.S value of the current waveform shown in figure below. l(t) 5

Q: 1. Sketch the output waveform Vi 20 V -20 V Vi 3 C1 HH 1.0uF _V1 -4 V Si 2+ Vo R2 1.2ΚΩ 4

A: In this question we need to draw a output waveform of the given circuit.

Q: Given an Emitter-Stabilized Bias Common Emitter amplifier with the following data: VCC = 12 V, Ic =…

Q: 2. Determine the following for the network shown below: a. gm b. ZiAMP C. ZOAMP d RD R1 Given…

A: Transconductance is the equation relating the efficiency of the system greater the Transconductance…

Q: Q1. Determine IE, VBE, VCE, and VCB in the circuit. Assume BDC = 150. Rc 390 RB wwww. w 8V 88 Assume…

Q: Q1. Determine IE, VBE, VCE, and VCB in the circuit. Assume BDC = 150.

Q: For a balanced Y-Y three phase system, the time domain expression for the phase-a line to neutral…

Q: parameters if IE =

A: BJT (bipolar junction transistor)- A transistor having a three terminal made up of semiconductor…

Q: for signals below.

Q: Refer to figure below, if the input A is more positive than input B, which diodes will be…

Q: circular coil iron ring has a cross sectional area of 5 cm squared and a length of 10cm. The…

A: We need to find out the flux for given coil.

Q: IS 19 load at power factor of 0.9 and efficiency o 28%. find the quality of cooling air required.…

A: Given,P = 4.2 MVAPOWER FACTOR = 0.9P= 0.9×4.2 = 3.78 MWEfficiency = 28%losses dissipated =…

Q: Q4: Find Vx in the network in fig.(4) using mesh (loop) analysis. 1202 M m 30v Fig.4 ≤lov 4VX + vx≤4

Q: Three impedances, Zan = 20+j0, Zbn = 16+j12, Zcn = 5-j15 ohms, are connected in wye across a 230V…

Q: Which of the following is considered a condition that is required for three-phase loads to be…

A: Let Z1, Z2 and Z3 be three loads, Z1, Z2 and Z3 are said to be in balanced load if they are having…

Q: Q1. Given the fixed bias circuit with VCC = 12V, RB = 240 KS2, RC = 2.2 ks and ß = 75. Determine the…

Q: 18. Refer to the circuit of Figure 19-64. a. Write the nodal equations. b. Solve for the node…

Q: For the circuit of Fig. below, calculate the phase and line currents. 3012 173/9: V 30 12 173/120 V…

A: The given circuit can be redrawn and the current in the branch can be parameterized as shown.

Q: In diodes, the space charge due to immobile ions in the depletion region establishes an electric…

Q: R₁=56 20v A) RTOTAL = B) I TOTAL CV-TOTAL = R67 E) V3 R3-20 R₂=55 R5=45 R6 = 3 R4=25 R7 = 3

Q: at Q2. (a) For the transistor circuit in Figure below, what is VCE when VIN minimum value of IB is…

Q: A wire carrying 31 A current passes between the poles of a strong magnet that is directed at angle…

Q: Given an Emitter-Stabilized Bias Common Emitter amplifier with the following data: Vcc = 12 V, Ic =…

A: Given an Emitter - stabilized bias common emitter amplifier 4) to find the value of collector…

Q: Q2. Find Q-point when VBB = 1V, 2 V and 3 V.. Assume VCE(sat) = 0 V. Re 1.0 KO RB www Vcc 10 V Bpc =…

A: Given An amplifier and it's parameters.we need to find out the operating point for different base…

Q: Find the following parameters 15.2 μA and Vc = iflg = 12 V for this transistor. a. lc b. ß C. VCE d.…

A: This problem can be done by knowing the relations between IC, Ib and Ie

Q: Find the Laplace transform of f(t) = 10 coswtu(t). Answer: 10s/(s² + ²).

A: Given f(t)=10cos(wt)u(t)

Q: Q4: Find Vx in the network in fig.(4) using mesh (loop) analysis. 12^ M m 30v vx=4r {4^ Fig.4 Elon…

Q: 1. A simple half wave rectifier consists of a diode and load. If the internal resistance of the…

Q: Simplify the following Boolean expressions, using four-variable maps:

A: In this question we need simply the given Boolean expression by using four variable k map.

Q: 2. For the given two stage amplifier circuit, hfe's = ß's = 150 and VBE = 0.7 V. Determine Avs VCC…

A: Two stage amplifier: Two stage amplifier has two transistor that are connected as common emitter and…

Q: Q1. An information as v/(t)=x (1) cos 10' √√3t, is desired to be transmited through a char If the…

A: Given circuit is shown below. Above circuit is Low pass filter. Transfer function is Vos=Vis×11+sCR

Q: Q4: Find Vx in the network in fig.(4) using mesh (loop) analysis. 12^ Y M 30v vx = 4₂ Fig.4 m Elon…

Q: Find the inverse Laplace Transform of the given function. 5/3s

Q: S Two sinusoidal voltages of maximum values 120 V and 80 V, respectively but differing in phase by…

A: We need to find out the equivalent voltage for given voltages .

Q: Q₁/ For the following signal, replote the signal with the following conditions. X(t) = {5t-3 t > 1 2…

A: To plot the given signal x(t) and then plot the signals a) 5x(t-5) b) 4x(t+4)

Concept explainers

Single Phase AC Circuit

Alternating Current (AC) is a type of electric power in which the electric current changes, both in magnitude and direction, at regular intervals. This AC Circuits can deliver power in either a Single Phase system or a Three Phase system.

Question

4.20 Calculate the inductive reactance in /km of a bundled 500-kV, 60-Hz,
three-phase completely transposed overhead line having three ACSR
11/13 kcmil conductors per bundle, with 0.5 m between conductors in the
bundle. The horizontal phase spacings between bundle centers are 10, 10,
and 20 m.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Analysis of Single Phase and Three Phase System

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 60-Hz, 765-kV, three-phase overhead transmission line has four ACSR 900 kcmil 54/3 conductors per phase. Determine the 60 Hz resistance of this line in ohms per kilometer per phase at 50C.
Calculate the inductive reactance in /km of a bundled 500-kV, 60-Hz, three-phase completely transposed overhead line having three ACSR 1 113 kcmil conductors per bundle, with 0.5 m between conductors in the bundle. The horizontal phase spacings between bundle centers are 10, 10, and 20 m.
The capacitance of a single-circuit, three-phase transposed line with the configuration shown in Figure 4.38, including ground effect, and with conductors not equilaterally spaced is given by C20lnDeqrlnHmH8 F/mÂ line-to-neutral where Deq=D12D23D133=GMD r= conductors outside radiusHm=(H12H23H13)1/3HS=(H1H2H3)1/3 Now consider Figure 4.39 in which the configuration of a three-phase, single circuit, 345-kV line with conductors having an outside diameter of 1.065 in. is shown. Determine the capacitance to neutral in F/m, including the ground effect. Next, neglecting the effect of ground, see how the value changes.
For the case of double-circuit, bundle-conductor lines, the same method indicated in Problem 4.27 applies with r' replaced by the bundles GMR in the calculation of the overall GMR. Now consider a double-circuit configuration shown in Figure 4.36 that belongs to a 500-kV, three-phase line with bundle conductors of three subconductors at 21 in. spacing. The GMR of each subconductor is given to be 0.0485 ft. Determine the inductive reactance of the line in ohms per mile per phase. You may use XL=0.2794logGMDGMR/mi/phase
Figure 4.34 shows double-circuit conductors' relative positions in segment I of transposition of a completely transposed three-phase overhead transmission line. The inductance is given by L=2107lnGMDGMRH/m/phase Where GMD=(DABeqDBCeqDACeq)1/3 With mean distances defined by equivalent spacings DABeq=(D12D12D12D12)1/4DBCeq=(D23D23D23D13)1/4DACeq=(D13D13D13)1/4 And GMR=[ (GMR)A(GMR)B(GMR)C ]1/3 with phase GMRs defined by (GMR)A=[ rD11 ]1/2;(GMR)B=[ rD22 ]1/2;(GMR)C=[ rD33 ]1/2 and r is the GMR of phase conductors. Now consider a 345-kV, three-phase, double-circuit line with phase-conductors GMR of 0.0588 ft and the horizontal conductor configuration shown in Figure 4.35. Determine the inductance per meter per phase in Henries (H). Calculate the inductance of just one circuit and then divide by 2 to obtain the inductance of the double circuit.
For either single-phase two-wire line or balanced three-phase three-wire line with equal phase spacing D and with conductor radius r, the capacitance (line-to-neutral) in F/m is given by Can=.
A three-phase overhead transmission line is designed to deliver 190.5 M VA at 220 kV over a distance of 63 km, such that the total transmission line loss is not to exceed 2.5 of the rated line MVA. Given the resistivity of the conductor material to be 2.84108-m, determine the required conductor diameter and the conductor size in circular mils. Neglect power losses due to insulator leakage currents and corona.
Transmission line conductance is usually neglected in power system studies. True False
For the overhead line of configuration shown in Figure 4.33 operating at 60 Hz and a conductor temperature of 700C, determine the resistance per phase, inductive reactance in ohms/mile/phase, and the current-carrying capacity of the overhead line. Each conductor is ACSR Cardinal of Table A.4.
Three ACSR Drake conductors are used for a three-phase overhead transmission line operating at 60 Hz. The conductor configuration is in the form of an isosceles triangle with sides of 20, 20, and 38 ft. (a) Find the capacitance-to-neutral and capacitive reactance-to-neutral for each 1-mile length of line. (b) For a line length of 175 mi and a normal operating voltage of 220 kV, determine the capacitive reactance-to-neutral for the entire line length as well as the charging current per mile and total three-phase reactive power supplied by the line capacitance.
If the per-phase line loss in a 70-km-long transmission line is not to exceed 65 kW while it is delivering 100 A per phase, compute the required conductor diameter if the resistivity of the conductor material is 1.72108-m.
A 60-Hz, three-phase three-wire overhead line has solid cylindrical conductors arranged in the form of an equilateral triangle with 4-ft conductor spacing. The conductor diameter is 0.5 in. Calculate the positive-sequence inductance in Wm and the positive-sequence inductive reactance in /km.