3D Problem 1. (P1) Three op-amps are connected in cascade configuration. An 80 microVolts signal is connected to the non-inverting input of the first op- amp. Both the 2nd and 3rd op-amps operates as inverting amplifiers. All feedback resistors are 420 KOhms while the input resistances are 71.4kOhms, 19.1kOhms, and 14kOhms respectively. Determine the output of the third stage stage. O a. 79.2 V O b. 9 V O c. 9000 mV O d. 792 mV

3D Problem 1. (P1) Three op-amps are connected in cascade configuration. An 80 microVolts signal is connected to the non-inverting input of the first op- amp. Both the 2nd and 3rd op-amps operates as inverting amplifiers. All feedback resistors are 420 KOhms while the input resistances are 71.4kOhms, 19.1kOhms, and 14kOhms respectively. Determine the output of the third stage stage. O a. 79.2 V O b. 9 V O c. 9000 mV O d. 792 mV

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.3P

See similar textbooks

Similar questions

Suppose the op amp shown has an fT of 1 MHz. What is the phase margin of the ampliﬁer?
Question 3: Please write answers to all parts of the question in the separate dot points as shown What is the circuit called? Discuss all components including voltage sources. Which components determine the closed-loop gain of the circuit? Describe the slew-rate of the op-amp. Describe the Common-Mode-Rejection ratio of the op-amp? What is the unity gain bandwidth? Describe the gain bandwidth product (GBP). Describe the GBP relationship between the break (critical) frequency and the gain? What two methods calculate the max frequency? If one produces a higher value of maximum frequency than the other, which would you use as the maximum frequency?
An inverting op – amplifier stage is designed with an input resistance of 5 KΩ and feedback resistance of 10 KΩ. The load resistance is 100 Ω with DC gain of 5x10^4 . The output internal resistance is 500 Ω while the input impedance is infinity, assuming an input voltage of 1.5 volts, calculate the following ?a) The AC gain ?b) The output voltage ?c) The looking back resistance ?
A certain op-amp has three internal amplifier stages with midrange gains of 30 dB, 40 dB, and 20 dB. Each stage also has a critical frequency associated with it as follows: fc1 = 600 Hz, fc2 = 50 kHz, and fc3 = 200 kHz. (a) What is the midrange open-loop gain of the op-amp, expressed in dB? (b) What is the total phase shift through the amplifier, including inversion, when the signal frequency is 10 kHz?
Please answer this two part question A) It is known that when an Op-amp is operated using the negative feedbackconfiguration, the output impedance reduces. Derive an expression that proves this. B) It is known that when an Op-amp is operated using the positive feedbackconfiguration, the output impedance increase. Derive an expression that proves this.
a) Design an inverting amplifier with a gain of 4. Use an ideal op amp, a 30 kohm resistor in the feedback path, and +-12 v power supplies. b) Using your design from part a, determine the range of input voltages that will keep the op amp in it's linear operating region. c) suppose you wish to amplify a 2 V signal, using your design from part a, with a variable feedback resistor. What is the largest value of feedback resistance that keeps the op amp in its linear operation region? Using this resistor value, what is the new gain of the inverting amplifier?
The voltage transfer characteristic for an operational ampliﬁer shown (a) What are the values of gain and offset voltage for this op amp? (b) Plot voltage gain A versus vid for the ampliﬁer voltage transfer characteristic.
Based on the plots of Vin and Vout, is the op-amp consistent with its inverting function? Justify your answer.
1. Design an inverting amplifier with a gain of 4. Use an ideal op amp, a 30 kΩ resistor in the feedback path, and ±12 V power supplies. 2. Using your design from part (a), determine the range of input voltages that will keep the op amp in its linear operating region. 3. Suppose you wish to amplify a 2 V signal, using your design from part (a) with a variable feedback resistor. What is the largest value of feedback resistance that keeps the op amp in its linear operation region? Using this resistor value, what is the new gain of the inverting amplifier?
An op-amp has an open-loop gain of 104 and a dominant open-loop pole at 4Hz. If an inverting amplifier with a gain of -100 is made from this op-amp, what is the resulting amplifier bandwidth? What is the gain-bandwidth product?
1. A non-inverting op-amp circuit has the open loop gain of 105 and the resistances R1 = 1k Ω and R2 = 39k Ω . Calculate (a) The actual value of voltage gain, (b) Considering the finite open loop gain, the ideal value of gain, and (c) The percentage error, when ideal voltage gain is compared with actual voltage gain.
Assume an inverting amplifier with input resistance 1 kilohm and feedback resistance of 100 kilohm. If the op-amp has GBP = 1 MHz, what is the closed loop amplifier bandwidth?