Three conducting wires are connected to a junction. The current flowing into the junction in two wires are i1 = 10sin 314t A and i2 = 15sin (314t - 45°) A. Kindly, solve for the current leaving the junction in the third wire. And state the value of current when t = 0.

Three conducting wires are connected to a junction. The current flowing into the junction in two wires are i1 = 10sin 314t A and i2 = 15sin (314t - 45°) A. Kindly, solve for the current leaving the junction in the third wire. And state the value of current when t = 0.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter29: Dc Generators

Section: Chapter Questions

Problem 1PA: You are working as an electrician in a large steel manufacturing plant, and you are in the process...

See similar textbooks

Related questions

Q: Find Vx, Vc, lo 12 Ω www 6Ω 892 13 + F "C 1

A: Given Circuit is shown below. Apply Laplace transform to the above circuit.

Q: 27. Sketch sin(377t + 60°) with the abscissa a. angle in degrees. b. angle in radians. c. time in…

A: The required parameters can be calculated based on the sinusoidal waveform representation. The time…

Q: how can draw energy band diagram? 1 & 2 & 3 & 4 Please answer in short like it definitely..

A: According to the question, we need to draw the energy band diagram for the given MOSFET a shown…

Q: The total or equivalent resistance is a. R/61 O b. none of the above O c. R*61 O d. --when 61…

Q: A Three-phase transposed line is composed of one conductor per phase with flat horizontal spacing of…

Q: 5. How does a capacitor work, and what is its purpose in an AC circuit? 6. In an AC circuit, Ohun's…

A: AC circuit is nothing but a circuit using alternating current, the magnitude and the direction of an…

Q: How many gates are needed to implement one of the following two equations: A- F=X+YZ + XZ. B- F =…

Q: 1ΜΩ + 18 V + VGSO ΜΑΞΙ 154 IDss = 10 mA 16 Vp = -4V OV 1516 1.5 ΚΩ 100 750 Ω

A: Self-bias FET: It is a voltage-controlled device. in this device, there is no current and 0 voltage…

Q: VDD J. VinM₁ - Vout V₂M₂ For the above circuit, let (W/L)1=(W/L)2=10, unCox-0.2mA/V², VTH=0.5V,…

A: For the above given question we need to calculate the value of DC bias current, transconductance and…

Q: 26. The potential difference of an energy source that provides 50 mJ of energy for every micro…

A: Given, Energy, W=50 mJ Charge, Q=1 μC=1×106 C

Q: the deviation d required amount. Example 10.4 A direct-FM transmitter has a varactor modulator with…

A: Given Few parameters of frequency modulation.we need to determine the block diagram,and oscillator…

Q: The difference between insulator and semiconductor is a. wider gap between valence and conduction…

A: In this question, We need to choose the correct options The difference between insulator and…

Q: Q4\ Find the total charge in the cylindrical system if p. = pz² nC/m, if p=3 and 0 <z < 5.

A: From the total charge density integrated equation

Q: Hot water heater Electric furnace Summer only vent fan Vacuum Pump Refrigerator Milk transfer pump…

A: Given Loads are given

Q: Example - Conducting spherical shells with roding a=10cm & 6=30 Cm are maintained at potential…

A: Given data, Radius:- a=10cm b=30cm Potential difference V=100Volts

Q: .…………………... In series connection of resistances, the relationship between the resistance and the…

Q: 741 + 5 5 ΚΩ 40 ΚΩ 20 ΚΩ να

Q: DESIGN A 24V SYSTEM USING EIGHT 12V PV MODULES 12 VDC 12 VDC 3.5A 12 VDO 3.5A 12 VDC 3.5A 3.5A 12…

A: To the design the 24 V pv module, the PV system will be arranged as

Q: Find the Norton equivalent circuit for the network in the shaded area of figure below

Q: What is the color of 47K ohm resistor with tolerance of +/-10% O a yellow -violet-orange-gold O b.…

A: Given R = 47k ohms

Q: Answer the following with True or False and correct the error if any: Note: For the False answers,…

A: Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: Consider the following chemical process temperature control system.a. Design the PD controller…

A: PD-control contains the proportional control's damping of the fluctuation and the derivative…

Q: Design a 16-1 MUX using 2-to-1 and 4-1 MUXs types only. F(w, x, y, z) = m (1, 2, 4, 7, 12)

A: For the above given question we need to implement the given minterms by using 2 to 1 and 4 to 1…

Q: For the circuit below, find I1, Iz and Vo using Nodal Analysis 330Ω V, -j450 Ω Τ j200 Ω 100 Ω 36/0°…

A: The following steps are to be followed while solving any electrical circuit using nodal analysis:…

Q: During a specific time segment of the day, a remote producer has surplus power and a load center…

A: Electrical power system has three stages, generation, transmission and distribution. All the three…

Q: 9) A dc voltage of 6V applied to the ends of 1km of a conducting wire of 0.5mm radius results in a…

A: Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: Next, draw the AC equivalent circuit for the amplifier in Figure 7 using a simple small signal model…

A: The amplifier circuit diagram is shown below,

Q: For the current-divider circuit in Fig. P3.19 calcula - a) i, and vo. b) the power dissipated in the…

A: In this question we will find unknown current, voltage and power consumed in 6 ohm resistor and…

Q: Instruction: Show complete solution. Use at least two decimal places. Express your answer in…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: -Q5/What the value of Rr.Fr, are required in the circuit below. 47 kOhm 0 022 uf HH 0.022 uf 47 kOhm…

Q: three phase, 60 Hz transmission line has an inductance of 1.08 mH per Km per phase and a capacitance…

A: In this question we will find phase constant , surge impedance for lossless line...

Q: 10) The induced torque (Tind) in a machine was defined as the torque generated by the internal…

Q: Find Vx using Nodal Analysis -j2 Ω 8 Ω j6Ω wwwm 40 /30° V 3Ω 10 Ω 5/0° A

A: Given data,

Q: Given: 1. x(n) = [1 2 3 5 7 9 4] and h(n) = [−1 2 -3] 2. x(n) = [1 4 6 7 8 3 5 2] and h(n) = [1 1 1…

Q: figure below. Find the Thévenin equivalent circuit for the portion of the network to the left of a-b…

Q: B- what are the disadvantages of the auto transformers? C-An auto transformer is used to step-down…

A: Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: A 220 V, 5 A d.c. energy meter is tested at its marked ratings. The resistance of the pressure…

A: It is given that: Voltage=V=220 VDC current=Idc=5 AResistance of the pressure circuit =RP=8800…

Q: 5v Wave amplitude = Vmax = 5V D1 # D4 Figure 2 D2 Calculate the value of I and Vo in the resistor of…

A: For the above given circuit diagram we need to calculate the value of voltage and current.

Q: Assume that the microprocessor can directly address 1M with a and 8 data pins. The maximum RAM…

A: Consider that the microprocessor can directly address 1M with a and 8 data pins. The maximum RAM…

Q: The bonding of all installations must comply with which of the following regulatory agencies?…

A: NEC or the National Electrical Code is a body that sets up standards for the safe practice of…

Q: How did the Integrated Circuit impact technology development during the 1950s and 60s?150-200 words

A: A set of electrical circuits on one small flat piece (or "chip") of semiconductor material, commonly…

Q: 3. For the circuit in Figure 3, find the mathematical expressions for ic (t) and vc (t) in the…

Q: Determine the impedance ZL for maximum average power transfer and the value of the maximum average…

Q: EX2: infinite line along the z-axis with 20 nc/m. Calculate the capacitance between p=10 and p=4 for…

A: Used first Maxwell's equation. Dot product of E(electric field) and top, bottom surfaces are equals…

Q: Find V (t), wc (0)

Q: Find T 100 pF 10 ΚΩ 20 ΚΩ 40 ΚΩ 30 ΚΩ

A: We need to find out the time constant for the given circuit

Q: The monthly reading of a Consumer's meter are as follow : Maximum demand = 50 kW Energy consumed =…

A: Tariff is the tax it is imposed by government on goods and service. In electrical engineering tariff…

Q: + I R₁VR₁ R₂ If I 29 A, R1 = 39 Ohms, and R2= 88 Ohms, what is the voltage across R1.

A: Given, I=29 AR1=39 ΩR2=88 Ω

Q: EX2: infinite line along the z-axis with 20 nc/m. Calculate the capacitance between p=10 and p=4 for…

Q: Calculate the reflection coefficient R for the finite potential well and confirm that R+T=1

Concept explainers

DC Generator

An electromechanical machine which converts input mechanical energy to respective output electric energy is called a generator.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

An engineer needs a resistor with a zero overall temperature coefficient of resistance at 20.0°c. She designs a pair of circular cylinders, one of carbon and one of Nichrome as shown in the figure below. The device must have an overall resistance of R1 + R2 = 15.0 Ω independent of temperature and a uniform radius of r = 1.40 mm. Ignore thermal expansion of the cylinders and assume both are always at the same temperature. (a) Can she meet the design goal with this method? Yes No (b) If so, state what you can determine about the lengths 1 and 2 of each segment. If not, explain.
Given:Vb = 100 voltsR = 10000 ohmsC = 200 μFAssuming that after a long period of time, the switch is flipped from position "A" to position "B" at t=0. Determine the current in the source-free circuit after 1 second.
For the circuit shown in Figure P1.77, solve for the current i x. What types of sources are present in this circuit?
COURSE: HIGH VOLTAGE TECHNIQUE In an insulating environment consisting of insulating oil (Ɛr1=12.5) and porcelain (Ɛr2=2.5), the electric field enters the porcelain environment through the oil at an angle of 50 relative to the normal of the border surface. Since the field strength is 87 kV/cm in oil environment, calculate the electric field strength in the porcelain environment, the tangent and normal components of the electric field strength in both environments. PLEASE MAKE A DETAILED SOLUTION!
Consider the circuit shown in the figure. The resistance of the wire used to make the inductor L is negligible compared to the resistors in the circuit. V=16 V, R1=14Ω, R2=105 Ω, and L=2 H. A) Assume that switch S has been closed for a long time so that steady currents exist in the circuit. Find the current being delivered by the battery, the current going through resistor R2 and the current going through the inductor. B) Now let's open the switch. Find the initial voltage across the inductor immediately after we open the switch. C) Let's suppose it has been 0.020 seconds since we opened the switch. Find the current through the inductor.
show solution please
Show solution
7. A conducting wire has a cross-sectional area of 2 mm² and a specific resistance of 5x10 m. designed for a heater with a power of 1200 Watt, operating at different potential 220 V. Determine a. Required wire length (L.) b. Large current on the wire c. Electrical energy is transferred into thermal energy within 15 minutes d. What is the power of the stove if the length of the wire is half the length in problem a (1/2)
A) Find the equivalent resistor of the circle between points a and b?B) If a constant voltage source (15V) is placed between points a and b, calculate a valueCurrent iS
2. A charge will experience a force in an electric field when it is: .............a. Stationaryb. Movingc. Stationary Or movingd. None of above3. The algebraic sum of voltages around any closed path in a network is equal to ..........a. Infinityb. 1c. 0d. Negative polarity4. A junction connects two (or) more than two network elements meet known as a ..........a. Nodeb. Branchc. Loopd. Mesh Final Research Project 7 | P a g e5. With Ohm's law, if voltage increases and resistance stays the same:..................a. current remains the sameb. power decreasesc. current increasesd. resistance decreases6. In superconductivity the conductivity of a material becomes .....................a. Zerob. Finitec. Infinited. None of the above7. If a negative charge move to a positive
A 30-volt electromotive force is applied to an ??-series circuit in which the inductance is 0.1 henry and the resistance is 50 ohms. Find the current ?(?) if ?(0) = 0. Determine the current as ? → ∞.