3) To provide a clamping force of 48,000 lb between two components of a machine (Tensile load, ignore bending), A set of six screws is used. The load is equally shared among three screws. Specify suitable standard screw, including grade of the material (Use Table 10.1 and 10.4 from the book to select the standard size screw. SAE Grade 7 type fasteners with UNC thread need to be used.). Clearly write down all the assumptions, and the details of the screw selected. Calculate the torque prescribed.

3) To provide a clamping force of 48,000 lb between two components of a machine (Tensile load, ignore bending), A set of six screws is used. The load is equally shared among three screws. Specify suitable standard screw, including grade of the material (Use Table 10.1 and 10.4 from the book to select the standard size screw. SAE Grade 7 type fasteners with UNC thread need to be used.). Clearly write down all the assumptions, and the details of the screw selected. Calculate the torque prescribed.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter6: Fasteners

Section: Chapter Questions

Problem 12RQ

See similar textbooks

Similar questions

One flange is attached to four 5x8 grade and M16 bolt connections with a total preload force of 80,000 N Calculate the factor of the bolt
A turn buckle, with right and left hand threads is used to couple two railway coaches. The threads which are square have a pitch of 10 mm and a mean diameter of 30 mm and are of single start type. Taking the coefficient of friction as 0.1, find the work to be done in drawing the coaches together a distance of 200 mm against a steady load of 20 kN.
1. A jack having square threads of 50 mm nominal diameter and 10 mm pitch is supporting a load of 89 kN. A double thread is used and the coefficient of friction maybe as low as 0.10 or as high as 0.15.a. Will this screw always self-locking?b. What is the highest torque necessary to raise the load?
An eyebolt is lifting a block weighing 360 lbs. The eyebolt is of SAE 1040 material with Su = 67 ksi and Sy = 55 ksi what is the stress area (in inches square) of the bolt if it is under the unified coarse series thread?
Task 2 Q1. A tensile testing machine operates using two lead screws. Both lead screws have a square thread profile and can withstand the maximum load of 16 tonnes & torque of 150 KNm. The pitch width p = l = 4 mm. what is the efficiency of the square thread?
Question No.16: A double threaded power screw with ISO metric trapezoidal threads with 15° semi-angle of thread is used to raise a load of 300 kN. The nominal diameter is 100 mm and pitch is 12 mm. the coefficient of friction at screw threads is 0.15. Neglecting collar friction, calculate; (i) torque required to raise the load, (ii) torque required to lower the load and (iii) efficiency of the screw.
(3) A single-threaded jackscrew has square threads. The screw diameter is l in. and there are 4 threads/in. A friction collar has a 2-in. outside diameter and an l-in. inside diameter. The coefficient of friction is 0.1 for the collar and 0.15 for the threads. How much force must be applied on a l2-in. (radius) jack lever to raise a load of 1,000lb?
Question 01: Draw and label any screw thread and a fastener separately. Also, discuss the types of stresses acting on screw threads and fasteners.
a single-start, square-threaded power screw with the following parameters: PARTS A - D circle final answers for each part A - A weight of 1500 N must be lifted. What is the total required torque necessary to lift this weight? Give your answer in units of N m. Part B - if the available power to drive the screw is 1,011 Watts, determine the fastest speed at which the weight can rise. Give your answer in units of mm/s, Part C - The efficiency of the preceding power screw (expressed as a number between 0 and 1, not as a percentage) is ? Part D - Suppose a high-quality thrust bearing was used to eliminate the collar friction. The efficiency of the screw would now be?
1) Draw and label any screw thread and a fastener separately. Also, discuss the types of stresses acting on screw threads and fasteners.
Refer to Problem 11.8. If an additional requirement is that the factor of safety against uplift is at least 4 with the dead load on (live load = 0), what should be the diameter of the bell?
(b)Find the torque required to raise the load of 15kN and mean diameter of triple threaded screw being 46mm. Also gIven pitch = 8mm and coefficient of friction is 0.15?