Answered: 4- 3 cables with same diameter are used…

4- 3 cables with same diameter are used to hold the plate. Calculate the tensile loads in all cables if the load P is applied to the center of the plate. C

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.7.7P: A bar of monel metal with a length L = 9 in. and a diameter d = 0225 in. is loaded axially by a...

See similar textbooks

Related questions

Q: Find the components force in joint * .E,D shown in the figure

A: Data given-

Q: For the loading condition given in the figure, the reactions occurring in the A and B supports…

Q: The aluminum bar with cross-sectional area of 160 mm2 carries the axial loads at the position shown…

A: Cross sectional area A = 160 mm2 E = 70 GPA

Q: Figure Q2 shows a rigid link supported by a pin at C and two A-36 steel wires. Each wire having an…

Q: The cross - sectional area of an aluminum bar is 170 mm². It carries an axial load at the positions…

A: Given: Cross-sectional area of an aluminium bar, A= 170 mm^2 E= 80 GPa= 80000 MPa Solution: Lets…

Q: Situation 5: A segment of a chain link is shown in the figure. D. A. If the diameter D is equal to…

A: Solution 5: Part (a) The diameter of the chain, d = 0.25 in. Allowable tensile stress, σallow = 2.5…

Q: 2-11. A wall bracket is constructed as showr in the figure. All joints may be considered pin…

Q: AB, BC, BD ropes made of material with elasticity value in Table 2 are in balance as shown in the…

A: Given Data: θ=90° β=120° α=150° FAB=40000 N Areas: AAB=200 mm2 ABC=173 mm2 ABD=100 mm2 Lengths:…

Q: The load W is to be lifted using the crane shown in the figure, neglect the weight of the crane.…

A: We are authorized to answer one question at a time since you have not mentioned which question you…

Q: The cable and boom shown in the figure support a load of 600 lb. Determine the tensile force, T, in…

Q: A link is shown in the figure. If the allowable combined stress at a-a is limited to 30 ksi, what is…

A: GivenσA=30ksi

Q: 3 cables with same diameter are used to hold the plate. Calculate the tensile loads in all cables if…

A: Givencables with load as shown below

Q: 2.10-3 A flat bar of width b and thickness 1 has a hole of diameter d drilled through it (see…

A: Given data: - The width of the bar is b. The thickness of the bar is t. The diameter of the hole…

Q: The figure below is a schematic drawing of a shaft that supports two V-belt pulleys. The loose belt…

A: Given, The yield strength of the material, sy=300 MPa The ultimate strength of the material, su=520…

Q: a. A member ABCD is subjected to point loads as shown in figure Task 2.b. Calculate (i) Force P…

Q: A 7.5kg sign is hung off of the end of a 3.7kg metal arm as shown in the figure. (Note that while…

A: Given Data: The mass of the arm is m1=3.7 kg. The mass of the sign is m2 = 7.5 kg. The center of…

Q: 3. The figure shows a frame supported by pins at A and D and carries a triangular load of maximum…

A: In the given example, member DCB will exert a compressive force at point B. We will consider FBDs of…

Q: At the nodes in the truss system given in the figure occurring displacement and the stress and…

Q: A force of 100 lb is applied to the frame shown (See the Figure below). Calculate the load in member…

Q: 2. Compute for the force in members FH, GH, and GI (USE METHOD OF SECTIONS) *For load P, take the…

Q: 4-13. A vertical square gate separates two compartments of a pressurized air tank, as shown in…

Q: 1.2-10 A car having a mass of 5500 kg is pulled slowly up a steep inclined track by a steel cable…

Q: 1. The cable and boom shown in the figure support a load of 600 lb. Determine the tensile force T in…

Q: Rod of diameter 20 mm is loaded with 5kN tension force. What is the magnitude of stress in the rod?

A: Given, Diameter of rod = d = 20 mm Force applied to rod = F = 5 kN = 5000 N Cross-sectional area…

Q: To assemble the truss (axial rigidity EA of the three bars) in Figure 3 the end point P of bar 2 has…

A: The change in length of the member 2 if the force acting in member 2 is F2,

Q: As shown in the figure, the two cables are joined at point C and balanced to a load. Calculate the…

Q: A steel bolt of 6 mm in diameter has a tensile load of 40 kN. Find the average tensile stress at the…

Q: Find the stress in each member of the truss shown in Fig. 4-11a. Indicate whether the members are in…

Q: A car weighing 130 kN when fully loadedis pulled slowly up a steep inclined track by asteel cable…

Q: In the figure below, the load that the pin at point O can safely carry is 5 kN. In this case, find…

Q: A picture frame is hung using the ropes 3 mm in diameter as shown in the figure. The maximum stress…

A: For solution refer below images.

Q: 4- 3 cables with same diameter are used to hold the plate. Calculate the tensile loads in all cables…

A: Given, the load P is supported by the system as shown in the Figure. For equilibrium, the deflection…

Q: Nframe of two members (AC) and (BD) are connected together at pin B. The other ends are…

Q: Use the method of sections to compute the force in members DF, EF, and EG of the cantilever truss…

Q: 1. (Problem 4.192 from the text book) Two vertical forces are applied to a beam of the cross section…

Q: A lifeboat hangs from two ship’s davits, as shown in the figure. A pin of diameter d = 0.8 in.…

A: Draw the free-body diagram of the pulley. Here, F is the shear force in the pin. Resolve the…

Q: Sketch a free-body diagram of each element in the figure. Compute the magnitude and direction of…

A: To sketch: The free body diagram of each element and compute the magnitude and direction of each…

Q: To assemble the truss (axial rigidity EA of the three bars) in Figure 3 the end point P of bar 2 has…

Q: The frame shown in Figure 3.1 has internal pins at points B, C and D and is supported by a pin at…

Q: Calculate the horizontal displacement at Joint H if the steel truss is loaded as shown in Figure…

Q: Compute the total elongation of the bar shown in Figure P3-37 if it is made from titanium 3-37.…

A: Reaction at A; Axial loading diagram: Now,

Q: A car weighing 130 kN when fully loaded is pulled slowly up a steep inclined track by a steel cable…

A: Given Data The weight of the car is: W=130 kN=130000 N The cross sectional area of the cable is:…

Q: A force of 100 lb is applied to the frame shown in the Figure below. Calculate the load in member…

Q: A steel bolt of 6 mm in diameter has a tensile load of 40 kN. Find the average tensile stress at the…

A: Step by step solution is given below

Q: 3-5.15. A pulley of 1-ft radius, supporting a load of 500 lb, is mounted at B on a horizontal beam…

Q: In the system in the figure, two rods carry the P force. a) Since the maximum stress that the rods…

Q: A load of W=5 kN is attached to end B of arm AB with the help of a wire wound on a frictionless…

Q: Problem (01): The pin-jointed truss in Figure (6) supports a load of P-2 kips at joint C. Determine…

Q: The maximum break stress of the chain ring seen in the figure on the side is 420 N/mm2, since the…

A: Normal stress is defined as the intensity of force exerted over a unit cross-sectional area. The…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

100%

4- 3 cables with same diameter are used to hold the plate. Calculate the tensile loads in all cables if
the load P is applied to the center of the plate.
C
II

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 150-lb rigid bar AB. with friction less rollers al each end. is held in the position shown in the figure by a continuous cable CAD. The cable is pinned at C and D and runs over a pulley at A. (a) Find reactions at supports A and B. (b) Find the force in the cable.
2.4-11 Three steel cables jointly support a load of 12 kips (see figure). The diameter of the middle cable is 3/4 in. and the diameter of each outer cable is 1/2 in. The tensions in the cables are adjusted so that each cable carries one-third of the load (ie., 4 kip). Later, the load is increased by 9 kips to a total load of 21 kips. (a) What percent of the total load is now carried by the middle cable? (b) What are the stresses crvand 0 in the middle and outer cables, respectively? Note: See Table 2-1 in Section 2.2 for properties of cables.
A long, slender bar in the shape of a right circular cone with length L and base diameter d hangs vertically under the action of its own weight (see figure). The weight of the cone is W and the modulus of elasticity of the material is E. Derive a formula for the increase S in the length of the bar due to its own weight. (Assume that the angle of taper of the cone is small.)
A steel cable with a nominal diameter of 25 mm (see Table 2-1) is used in a construction yard to lift a bridge section weighing 38 kN. as shown in the figure. The cable has an effective modulus of elasticity E = 140 GPa. (a) If the cable is 14 m long, how much will it stretch when the load is picked up? (b) If the cable is rated for a maximum load of 70 kN, that is the factor of safety with respect to failure of the cable?
A plane Frame with pin supports at A and E has a cable attached at C, which runs over a friction-less pulley at F(see figure). The cable Force is known to be 500 lb. (a) Find reactions at supports A and E. (b) Find internal stress resultants N, V, and M at point H.
A plane Frame is restrained at joints A and D, as shown in the figure. Members AB and BCD are pin connected at B. A triangularly distributed lateral load with peak intensity of SO N/m acts on CD. An inclined concentrated force of 200 N acts at the mid-span of BC. (a) Find reactions at supports A and D. (b) Find resultant forces in the pins at B and C.
Repeat Problem 2.3-29 if vertical load P at D is replaced by a horizontal load P at D (see figure).
Two separate cables AC and BC support a sign structure of weight W = 1575 lb attached to a building. The sign is also supported by a pin support at O and a lateral restraint in the '-direction at D. (a) Find the tension in each cable. Neglect the mass of the cables. (b) Find the average stress in each cable if the area of each cable is Ae= 0.471 in2.
Find expressions for all support reaction Forces in the plane frame with load 3P applied at C as shown in the figure. Joints A and D are pin supported, and there is a roller support at joint F. The lengths and the properties of the members are shown in the figure. Neglect the weights of all members. Select Rfas the redundant.
A column, pinned at top and bottom, is made up of two C 6 x 13 steel shapes (see figure) that act together. Find the buckling load (kips) if the gap is zero. Find required separation distance d(inches) so that the buckling load is the same in y and z directions. Assume that E = 30,000 ksi and L = 18 ft. Note that distance d is measured between the centroids of the two C shapes.
An idealized column is composed of rigid bars ABC and CD joined by an elastic connection with rotational stiffness ßRat C. There is an elastic support at B with translational spring stiffness ß and a pin support at D. Find the critical buckling loads for each of the two buckling modes of the column in terms of ßL. Assume that ßR= ßL2. Sketch the buckled mode shapes.
A plane frame is constructed by using a pin connection between segments ABC and CDE. The frame has pin supports at A and E and joint loads at B and D (see figure). (a) Find reactions at supports A and E. (b) Find the resultant force in the pin at C.