4-55. Determine the moment of the force F about an axis extending between A and C. Express the result as a Cartesian vector.

Q: Part A The 12-lb block has a speed of 4 ft/s when the force of F = (8t2) lb is applied. The…

A:

Q: Which of the following forces in the Figure below has the moment about point A equals 54 Nm,…

A:

Q: Kubuta geothermal power plant has 83.7 % efficiency. What is its actual power capacity if the…

A:

Q: Given the isometric drawing, draw the multiview projection. The multiview projection of the glass…

A: Given 3D model To find Multi-view

Q: Q1/ The load 10 KN applied on the beam results a flexural stress. answer (TRUE or .(FALSE Point D 10…

A: Explain- Will 10 kN laod cause flexural stress.

Q: Which of the following statements describes the third law of thermodynamics? -The enthalpy of the…

A:

Q: Eastern village installed wind turbine power plant in a capacity of 7,200 KW. If each turbine rated…

A: Power Plant Capacity = 7200 KW Wind turbine rating = 200 KW Efficiency of turbine = 98% Actual power…

Q: A projectile is launched from point A with the initial conditions shown in the figure. Determine the…

A:

Q: في الشكل المجاور قيمة واتجاه المحصلة هو

A:

Q: During the analysis of fluid flow, we are more often interested in obtaining the elocity, and one of…

A: The cross-section should be perpendicular to the principle direction of flow

Q: The 5 kg cylinder is released from rest in the postion shown in the figure below. Determine the…

A: Find the maximum compression in spring.

Q: 8

A: Given-Data:-Tensile stress=40MpaSpecific surface energy =0.3J/m3Modulus of elasticity =69GPa…

Q: Oil with a specific weight of 10.55 kN/m^3 is flowing from A to B through the special fabricated…

A:

Q: The force P is applied to the 38-kg block when it is at rest. Determine the magnitude and direction…

A:

Q: UZ7 Tme 1oad z KTN applie u on the peam results a flexural stress. answer (TRUE or .(FALSE * Point D…

A: What type of stress will be there due to axial load 2 kN.

Q: :Q11/ The value of moment at point C is Point D

A:

Q: 5 kg of steam at 10 bar was sampled and passed to a barrel calorimeter whose water equivalent at…

A: We took a sample of 5 kg of steam at 10 bar and fed it into a barrel calorimeter with a 20 kJ/K…

Q: If a car accelerates at the rate of a in t seconds and decelerated at the rate of 0.5a for 2t…

A:

Q: Derive the one-dimensional heat conduction equation for a sphere.

A: The general equation for one-dimensional heat conduction can be given as: q=1r2∂∂rr2k∂T∂r

Q: A Carnot heat pump is used to maintain the temperature inside a building at 20 °C. Significantly,…

A:

Q: Fluid of constant density is flowing at a velocity of 0.5 meter per second into a horizontal nozzle…

A:

Q: Deposited P110,000 for 31 days. The net interest after deducting 20% withholding tax is P 795.67.…

A: Given Data P=110,000 n=31daya r=20%

Q: Determine the axial force (kN) in each member of the assembly shown below. Member Cross-Sectional…

A: Trusses are constructions made solely of components with two forces. Each truss member is believed…

Q: Shown below is an inverted U-tube which is used to drain alcohol from a tank reservoir. The bend of…

A:

Q: An Otto cycle has a clearance of 8 % and heat added of 1000 kJ. Find the heat rejected. ANSWER:…

A: Clearance= 8% Heat added, Qadded= 1000 kJ   To find: Heat rejected, Qrejected

Q: er plant has an engine capacity equal to 15% more of that engine r

A:

Q: (1) During a rockburst (violent rock failure underground), a rock block was ejected as a projectile…

A:

Q: Falling Sphere Viscometer Given:             Inner diameter of cylindrical tube = 0.03 m…

A:

Q: cy of a diesel fuel power plant is 13% 0Oste mwhich is eg

A:

Q: A 250 lb block A is released from rest. It pulls the 400 lb block B up the 30 ramp. The kinetic…

A:

Q: The force P is applied to the 52-kg block when it is at rest. Determine the magnitude and direction…

A:

Q: The crank AB of the mechanism shown on the right is connected to a slider B which moves on the…

A:

Q: a) If the spring is cut by half of its length and is loaded by the same load, compute the…

A:

Q: why the thermal conductivity value (for a particular material) is important in engineering?

A:

Q: 2, A diesel Cycle engine with k of 1.33 has an air standard efficiency of 60.5%. The temperature at…

A: Calculated the maximum temperature of the cycle. and temperature at the beginning of compression and…

Q: PROBLEM S5.3 A thin spherical vessel 1 m in diameter and 12 mm thick is filled with water. More…

A: The amount of extra water required to reach this pressure: ∆V = ( 1.526 × 10-3 ) m3.

Q: 1- Replace the distributed loading by an equivalent resultant force, and specify its location on the…

A:

Q: at Dimeter lo mm, ♡ = L.6L/5 %3D shact = 90°elbow bend tube 26 cm %3D Determine lenght 9o cm

A: Given that, Diameter of pipe, D=10 mm,Flow rate of water, Q=1.6 l/sec,Actual Head loss ∆hact=26…

Q: Calculate the magnitudes of the angular velocities, ωs and ωp, if the magnitude of the resulting…

A: Given data as per question OC=e=75cm=0.75 mdiameter=21 cm=0.21 mradius=0.105…

Q: 3. For a single cylinder petrol engine works on the diesel cycle, the pressure at the beginning and…

A:

Q: What laws of thermodynamics applicable to the compression molding machine concept?

A: Given question: What laws of thermodynamics are applicable to the compression molding machine?

Q: Problem 8.14 A curved bar of circular cross-section 100 mm in diameter has a radius of curvature of…

A:

Q: A steel cylinder 0.01653 m contains 5.6 kg of ethylene gas C,H.. molecular weight 28. Calculate the…

A: Find the temperature of gas.

Q: 2. Calculate the reaction at A and B for the beam loaded as shown in Figure 2 400 lb/ft B 12'- 6'…

A:

Q: The airplane travels along a straight runway with an acceleration described by the graph. If it…

A: The velocity attained in first 10 seconds can be determined as shown below. The time required to…

Q: A R-134A vapor refrigeration cycle cycle operates at an evaporator temperature of 20 Celsius  and a…

A:

Q: Water is flowing at a rate of 187 L/s through a 116 m horizontal pipe having a diameter of 335 mm.…

A: Given:Q=187 L/s =0.187 m3/sL=116 md=335 mm∆P=275 mm Hg

Q: The velocity of a particle which moves along s-axis is given by v = 2 - 4t + 5t32, where t is in…

A:

Q: 1. Locate the centroid of the shaded area shown in the figure 1.

A:

Q: Taking the velocity v and the gravitational spring force F, as the state vari- ables (Note: This is…

A: State-space framework portrayal establishes the groundworks for current control hypothesis. It…