I need the answer as soon as possible 4- The 200 kg, 5 m wide rectangular gate shown in Figureis hinged at B and leans against the floor at A making anWaterangle of 45° with the horizontal, The gate is to be opened3mfrom its lower edge by applying a normal force at its center.45Determine the minimum force F required to open the water gate.19

Answered: Image /qna-images/answer/1a062235-55c9-4f25-8bcb-94712ea0566a.jpg

4- The 200 kg, 5 m wide rectangular gate shown in Figure is hinged at B and leans against the floor at A making an angle of 45° with the horizontal. The gate is to be opened from its lower edge by applying a normal force at its center. Determine the minimum force F required to open the water gate.

4- The 200 kg, 5 m wide rectangular gate shown in Figure is hinged at B and leans against the floor at A making an angle of 45° with the horizontal. The gate is to be opened from its lower edge by applying a normal force at its center. Determine the minimum force F required to open the water gate.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.38P: The 40-kghomogeneous disk is placed on a frictionless inclined surface and held in equilibrium by...

See similar textbooks

Related questions

Q: (4) Explain how could you determine the resultant force on a curved surface inmnersed in a liquid?…

Q: 3.70 The plane rectangular gate can pivot about the support at B. For the conditions given, is it…

Q: gate AB 4 ft long and 2 ft wide is held in position shown due to the spring whose constant is 96.0…

A: Given:length og gate, l=4 ftwidth of gate, w=2 ftk=96.0 lbf/inx=1.5 ft

Q: For the quarter circle gate BC with a hinge at C, the force P = kN to hold the gate stationary for…

Q: A 250 KG cylinder rests in a long channel as shown. Find the forces acting on the cylinder by the…

Q: The ship ladder in the figure is 1500 N and its center of gravity is at G. What must be the rope…

Q: A rigid, vertical rod of negligible mass is connected to the floor by a bolt through its lower end,…

A: Let us consider the length of the rod be L, First calculating the tension in the wire as follows –…

Q: Based on the following figure and its description, answer Q1, Q2, Q3, Q4 and Q5. Isosceles…

Q: (c) A gate with 2 m width is located under the water as shown in Figure Qlc. IF the force (F)…

Q: . The rigid gate, OAB, of fig. (2.6) is hinged at O and rests against a rigid support at B. What…

A: Solution:

Q: Q2: For the system shown in figure, all chains are of negligible weight, if the tensile force in…

A: Given data: The tension in the chain D is TD=7820 N The acceleration due to gravity is g=10 ms2

Q: 4- The 200 kg, 5 m wide rectangular gate shown in Figure asm is hinged at B and leans against the…

Q: Consider the gate (A-B-C-D) shown in the figure below. The gate is hinged at point A and is massless…

Q: The 300 kg, 5 m wide rectangular gate shown in Figure Q1(b) is hinged at B and leans against the…

Q: Please answer in essay: From the figure below, discuss the internal effect of the external forces…

A: EXTERNAL AND INTERNAL FORCES External forces are powers brought about by outside specialist outside…

Q: keep the gate from opening when The circular gate ABC has a Im radius and is hinged at B. Compute…

Q: A open tank containing water (see figure) has a circular door AB with radius of 5 ft, inclin at an…

Q: 4- The 200 kg, 5 m wide rectangular gate shown in Figure 0.5 m is hinged at B and leans against the…

Q: Gate AB 7.5 ft wide into the paper, hinged at A, and restrained by a stop at B. The water is at…

A: Any action that attempts to keep or change the motion of a body, or to deform it. The magnitude of…

Q: A 6-m long ladder has a mass of 16 kg, and its center of gravity is 2.4 m from the bottom along the…

Q: 6- The rectangular gat has dimensions 6 m by 2 m. Neglect the weight of the gate. Determine (a) The…

Q: The block shown in the figure below is acted on by its weight, W = 1300 Lbs, a horizontal force H =…

Q: Isosceles triangular gate AB, as shown in the figure, is hinged at A. The horizontal force ( P) is…

A: Given: The triangular gate is shown below:

Q: The hanging structure in the figure below is homogeneous. Its weight (40 kg) is acting at the center…

Q: 1- A 60 cm square gate has its top edge 12 m below the water surface. It is on a 45 angle and its…

Q: Question-3 A gate having the triangular shape shown in the figure below is located in the vertical…

Q: The valve of a water pond shown in the figure has a quarter cylinder shape with a length of 8 m…

A: Write down the above values using suitable variables. Here l signifies cylinder length, a signifies…

Q: 1. (a) The gusset plate in Figure la is subjected to the forces of four members; F is 10 kN and the…

Q: A gusset plate is subjected to the forces shown in the figure below. Find the magnitude (F) And…

Q: Hinge

A: For solution refer below images.

Q: 1. In a room with a ceiling height of 2.6 meter, a 2.5 meter plank is supported by a cable attached…

Q: Q4. A weight of 700 N was place 1 meter from the pivot as shown in the figure below. Determine the…

Q: The circular gate ABC in the figure below has a 1-m radius and is hinged at B. Compute the force P…

Q: The gate in the figure shown is 1.5m wide, hinged at point A and rests against a smooth wall at B.…

A: Given:- Gate is 1.5 m wide. ( W = 1.5 m ) To Find:- The total force on the gate due to…

Q: 4- The 200 kg, 5 m wide rectangular gate shown in Figure 0.5 m is hinged at B and leans against the…

A: Given, m = 200 kg w = 5 m Consider below FBD: Here, F = Applied ForceW = Weight of the gateFh =…

Q: Determine the magnitude of horizontal and vertical components of the total force per meter length…

A: Solt>. Hovironta} am A Verticals Com ponent “{ force Gr pot Ac vs Fin = Pg hyA = oo 9-H xX (242)…

Q: 4 - The 2-m-diameter gate AB in Fig. 3-9 swings about a horizontal pivot C located 40 mm below the…

A: Given data: Diameter of gate AB, d = 2 m. The condition of having no unbalanced moment about C is…

Q: A 3.5m - high . 5m wide rectangular gate is hinged at the top edge at A and is restrained by a fixed…

A: The total area of the rectangular gate is A= 3.5×5=17.5m2 Let ρ be the density of water , ρ=1000kgm3…

Q: 6-m-wide rectangular gate shown is hinged at B and leans against the floor at A making an angle of…

Q: (b) The 300 kg, 5 m wide rectangular gate shown in Figure Q1(b) is hinged at B and leans against the…

Q: In the simple cage system in the figure, which of the following is the absolute value of the force…

Q: The 500-kg load on the hydraulic lift shown in the figure on the right is to be raised by pouring…

A: Given :- Load on hydraulic lift (L) = 500 kg × 9.81 m/s2 Load on hydraulic lift (L) = 4905 N To…

Q: Semicircular gate AB hinged at B. Calculate the horizontal force (P) required for equilibrium. 5m…

Q: $Gate AB in Fig. 3-5(a) is 4 ft wide and is hinged at A. Gage G reads -2.17 psi, and oil of specific…

Q: 15. The force, P, to hold the 3-m wide gate (yes, the gate goes outside of the water) in the…

Q: [2] Water in a U-tube is held at unequal heights by placing a thumb over one end. The diameter of…

A: Note : As per our company norms, we can answer only three-subpart at a time. Please resubmit the…

Q: Q2: For the system shown in figure, all chains are of negligible weight, if the tensile force in…

Q: A rectangular gate (6m x 4m) is e hinged at A and supported by a stopper as shown. Find the reaction…

A: Given: The area of gate, A = 24 m2 The centre of pressure measured from A, yp = 3+0.4641 = 3.4641 m…

Q: For the quarter circle gate BC with a hinge at C, the force P = . . kN to hold the gate stationary…

Question

I need the answer as soon as possible

4- The 200 kg, 5 m wide rectangular gate shown in Figure
is hinged at B and leans against the floor at A making an
Water
angle of 45° with the horizontal, The gate is to be opened
3m
from its lower edge by applying a normal force at its center.
45
Determine the minimum force F required to open the water gate.
19

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Two concrete blocks weighing 320 lb each form part of the retaining wall of a swimming pool. Will the blocks be in equilibrium when the pool is filled and the water exerts the line loading shown?
The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016, determine the force F required to advance the bar at a constant speed.
The high-pressure water cock is rigidly attached to the support at D. Neglecting the weights of the members, draw the FBD of the entire assembly and count the unknowns.
The 40-kghomogeneous disk is placed on a frictionless inclined surface and held in equilibrium by the horizontal force P and a couple C (C is not shown on the figure). Find P and C.
A 200 kg, 5 m wide rectangular gate is hinged at B and leans against the floor at Amaking an angle of 45 degrees with the horizontal (figure above). Determine theminimum force F, applied at the center of the gate required to open it.
The 300 kg, 5 m wide rectangular gate shown in Figure Q1(b) is hinged at B and leansagainst the floor at A making an angle of 45o with the horizontal. The gate is to beopened from its lower edge by applying a normal force at its centre. Determine theminimum force F required to open the water gate
Q4: of a car غطاء محرك The i Jul. The bonnet is held open at an angle of 60° to the horizontal by a vertical force V applied at one end of the bonnet (shown on the diagram). The long, has a weight of 25 N and its center diagram shows the open bonnet bonnet is 0.90 m of gravity G is 0.35 m from the hinge at O. 1) On the diagram, draw and label the two forces other than V acting on the bonnet. By taking moments about A, Proof that the vertical 2) force V applied at the end of the bonnet is 9.7 N. 3) Calculate the magnitude of the force acting at the hinge ON.
Consider a floor crane operated by a driver which carries a drum as shown in figure. The total weight of floor crane and driver is 2700 kg acting at the point of center of gravity, G. mm; = 1 = Considering L1 = 14m, L2= 3 m L3 - 6 m, 14 = 2 m LS = 1 m; L6=7m 1. If the weight of the drum lifted by the floor crane is 800 kg, determine the total normal reaction on the rear wheels at A and total normal reaction on the front wheels at B when the boom is inclined at an angle of 25" with the horizontal, 2. Utilizing the same data given above for the same position of boom, determine the largest weight of the drum that can be lifted without causing the crane to overturn. (Hint: When the floor crane tends to overturn about point B, the wheel at A will leave the ground). Note: 1. Consider the entire system as coplanar 2. Take g 9.81 m/s wherever necessary = 9 Total normal reaction on the rear wheels at A= Total normal reaction on the front wheels at B= Largest weight of the drum=
- A 3.5m - high . 5m wide rectangular gate is hinged at the top edge at A and is restrained by a fixed ridge at B. Determine the force exerted on the gate at Point B
A crane is used to lower weights into a lake for an underwater construction project. Determine the tension in the rope of the crane due to a 3-ft-diameter spherical steel block (density = 494 lbm/ft3) when it is (a) suspended in the air and (b) completely immersed in water.
A gate AB 4 ft long and 2 ft wide is held in position shown due to the spring whose constant is 96.0 Ibf/in. The spring is located compressed 1.5 ft in such a way as to keep the gate in equilibrium. Assume that on the gate (which moves through a circular sector BD as shown in Fig. figure), the force due to the spring is always horizontal. Determine the height d of the water.
Cords are looped around a small spacer separating two cylinder each weighing 400kn and pass over a frictionless pulleys to weights of 200KN and 400kn. Determine the angle and the pressure N between the cylinder and smooth horizontal surface