4. A 10 cm diameter pipe has a discharge of 500 Vs. At a section, the pipe has sudden expansion to a size of 15 cm diameter. If the pressure just upstream of the expansion is 22 kN/m², calculate the pressure just after the expansion. Assume the pipe to be horizontal at the expansion region. (Ans: 22.285 kPa) W

4. A 10 cm diameter pipe has a discharge of 500 Vs. At a section, the pipe has sudden expansion to a size of 15 cm diameter. If the pressure just upstream of the expansion is 22 kN/m², calculate the pressure just after the expansion. Assume the pipe to be horizontal at the expansion region. (Ans: 22.285 kPa) W

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q2) What is the pressure at point (B)inside the pipe shown in figure below if the water jet velocity at point (A) is 18 m/s.. 15m D= 75 mm D 200 mm 0.5 m B-
The discharge flowing down the pipe is 0.03 m3/s and the pressure at 2 is 20kPa. Assuming the losses in the pipe is negligible. A U-tube is connected between points 1 and 2 to determine the difference in their pressure, what would be the value of y. Liquid flowing in the pipe is water
In a pump the suction and delivery pipes are of the same size and are at the same level. At a given discharge the loss of head between a point A on the suction side and a point B on the delivery side is 3.0 m. If the pressure at point B is 120 kPa and the head developed by the pump is 10 m, the pressure at point A, in kPa is (Water is the flowing fluid)
2. Oil of specific gravity of 0.90 is discharging through a 100 mm circular sharp edge orifice in the end of a 120mm pipe. The pressure head on the center line of the pipe just upstream from the orifice is 9m of oil, and discharges takes place into a closed tank in which the vapor pressure is - 20 kPa. Use C = 0.68 and Cv = 0.97. Compute the discharge. 120 mm pipe P = - 20 kPa 100 mm orifice
Oil (s = 0.90) is discharging through a 100mm circular sharp edge orifice in the end of a 150mm pipe. The pressure head on the centerline of the pipe just upstream from the orifice is 9m of oil, and discharges takes place into a closed tank in which the vapor pressure is 20 kPa. The discharge is not submerged. The orifice coefficients are C = 0.68 and Cv = 0.97. Compute the discharge. P=-20 KPa
Consider that we have a horizentral pipe, like shown in the sketh, which is carrying in this case, cooling water at 10 ℃。The elevation of the big tank of cooling water is 100 m, the elevation of the center line of the pipe is 20 m, the length of the pipe is 2000 m. Head loss in the pipe is , D=20 cm, the rate of flow is 0.06 m3/s, . Please calculate the pressure in the pipe.
(4) Consider that we have a horizentral pipe, like shown in the sketh, which is carrying in this case, cooling water at 10 °C. The elevation of the big tank of cooling water is 100 m, the elevation of the center line of the pipe is 20 m, the length of the pipe is 2000 m. Head loss in the pipe is 0. 07 L / D) V? H. D=20 cm, the rate of flow is 0.0 a=1 ase calculate the 2g pressure in the pipe. Elevation = 100 m Elevation = 20 m L=2000 m %3D II ||
1 a) A 2-mm-diameter clean glass tube is inserted in water at 15°C (Figure 1.2). Determine the height that the water will climb up the tube. The water makes a contact angle of 0° with the clean glass. ADo h W=y¥ Air Water Figure 1.2
The pressure gauges are inserted at A and B in a vertical pipe converging water. The diameters at A and B are 150mm and 75mm respectively. The point B is 2.3m below point A. When rate of flow down the pipe is 0.021m³/s. The pressure at B is 117.72 KN/m² greater than at A. The losses in pipe between A and B are expressed as(KVa²/2g) where Va is velocity of A. Find the value of K. If the pressure gauges at A and B are replaced by tubes filled with water and connectef to a u-tube containing Hg(SHg=13.6) calculate the value of the reading manometer.
The diameter of a pipe changes gradually from 6 inches at A to 18 inches at B. A is 15 ft lower than B. If the pressure at A is 10 lbs per square inch and at B, 7 lbs per square inch when there are 5.0 cubic ft per second flowing, determine: a. the direction of flow. b. the frictional loss between the two points B. If in Problem 1 the direction of flow is reversed, determine the pressure at A if all other factors, including the frictional loss, remain the same. C. In Problem 1, determine the diameter of pipe at B in order that the pressure at that point will also be 10 lbs per square inch, all other factors remaining constant. D. Determine the discharge in Problem 1, assuming no frictional loss, all other conditions remaining as stated. E. What would be the difference in pressure in pounds per square inch between A and B, Problem 1, if there were 6.2 cubic ft per second flowing, neglecting friction.
Determine the pressure at the center of the pipe from the piezometer shown. 200mm WATER 75mmØPIPE
The fluid in the tank is water. Flow is steady state, incompressible and nonviscid. It is known that the pressure at point (1) is 41.5 kPa(gage). Determine the height x of the tank? 5-m 0.02-m diameter 0.03-m diameter | (1) 0.01-m diameter