4. (a) Consider the differentiating operational amplifier circuit. The feedback resistor is 220 k2, and the input capacitor is 22 uF. If a ramp voltage applied across the input which is -2 V after one second. It increases by -2 V every second for six seconds. Calculate the output voltages of the amplifier for each second after the ramp voltage on the input has been applied. From this draw a graph of output voltage against time and compare this to the input voltage.

4. (a) Consider the differentiating operational amplifier circuit. The feedback resistor is 220 k2, and the input capacitor is 22 uF. If a ramp voltage applied across the input which is -2 V after one second. It increases by -2 V every second for six seconds. Calculate the output voltages of the amplifier for each second after the ramp voltage on the input has been applied. From this draw a graph of output voltage against time and compare this to the input voltage.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.3P

See similar textbooks

Similar questions

Given in the figure is a two-stage amplifier design that employs negative feedback. Answer the following questions. Use the notation (R1 + R2 + ... + Rn) for series resistors and (R1 || R2 || ... || Rn) for parallel resistors for clarity and ease. Assume that the transistors are already biased properly in the saturation region and ro1 = ro2 → ∞. Also assume that the capacitors have infinite capacitance. 1.) Find the expression for the open loop gain Av 2.) Derive the resistance Rin which is the resistance that can be seen at the input port of the amplifier
Find the loop gain, ideal voltage gain, actual voltage gain, input resistance, and output resistance for the feedback ampliﬁer shown if a 4-kΩ load resistor is connected to the output of the ampliﬁer.
If a signal voltage of 30mV is applied to inverting amplifier, find output voltage and phase relationship with input voltage if it has input resistance of 25 ohm and feedback resistance of 50 ohm. NOTE : KINDLY ELABORATE BRIEFLY
The circuit as shown is a shunt-shunt feedback amplifier. Use feedback analysis to find the midband input resistance, output resistance, and transresistance of the amplifier if RI = 500 Ω, RE = 2 kΩ, β0 = 100, VA = 50 V, RL = 5.6 kΩ, and RF = 47 kΩ, when vi and RI are replaced by a Norton equivalent circuit. What is the voltage gain for the circuit as drawn?
a) Design an inverting amplifier with a gain of 4. Use an ideal op amp, a 30 kohm resistor in the feedback path, and +-12 v power supplies. b) Using your design from part a, determine the range of input voltages that will keep the op amp in it's linear operating region. c) suppose you wish to amplify a 2 V signal, using your design from part a, with a variable feedback resistor. What is the largest value of feedback resistance that keeps the op amp in its linear operation region? Using this resistor value, what is the new gain of the inverting amplifier?
An ampliﬁer has an open-loop voltage gain of 90 dB, Rid = 50 kΩ, and Ro = 5000 Ω. The ampliﬁer is used in a feedback conﬁguration with a resistive feedback network. (a) What is the largest current gain that can be achieved with this feedback ampliﬁer? (b) What is the largest transconductance that can be achieved with this feedback ampliﬁer?
A voltage follower’s closed-loop voltage gain Av is described by Eq. as shown. (a) What is the minimum value of loop gain T required if the gain error is to be less than 0.02 percent for a voltage follower?(b) What value of open-loop gain A is required in the ampliﬁer?
An amplifier has voltage gain with the feedback of 100. If the gain without feedback changes by 409 and the gain with feedback should not vary more than 8%, the values of open-loop gain and feedback ratio will be respectively given by
The feedback ampliﬁer shown has R1 = 1kΩ, R2 = 100 kΩ, RI = 0, and RL = 10 kΩ. (a) What is β? (b) If A =92 dB, what are the loop gain T and the closed loop gain Av? (c) What are the values of GE and FGE?
Suppose we have a two-stage cascaded amplifier with an ideal transconductance amplifier as the first stage and an ideal transresistance amplifier as the second stage. What type of amplifier results and what is its gain in terms of the gains of the two stages? Repeat for the amplifiers cascaded in the opposite order.
The classic feedback ampliﬁer as shown has β =0.125. What are the loop gain T, ideal closedloop gain AIdeal v , actual closed-loop gain Av, and the fractional gain error FGE if (a) A =∞? (b) A =84 dB? (c) A =20?
Compare the closed-loop voltage gain, k = Vo/Vs, for the loaded and unloaded dependent source model of the Voltage Follower with the ideal model of the Voltage to examine the impact of the load, RL on k. - Using any circuit analysis method, derive expressions for the closed-loop gain, k = Vo/Vs, for the ideal opamp Voltage Follower ,both the unloaded ,loaded Voltage Follower using the dependent source model. simplify both of the closed-loop gain expressions for the dependent source models by applying the ideal opamp parameters: A --> infinity , R_i -->infinity and R_0 --> infinity.