4. A force of 400 N is exerted 20 cm from the axis rotation. What is the resulting moment of force? a. 80 N b. 80 N-m c. 200 N d. 200 N-m

Q: R(S) XIS K 1 S+5 s+ 2 s+3 Y(s)

A:

Q: A cascade system is to be designed to attain a temperature of 213K in an environment of 313K. The…

A:

Q: The truss is subjected to the system of forces as shown in the following figure. The truss is…

A:

Q: For the truss shown, find the magnitude of the force F BE using the figure and the given data. F₁ =…

A:

Q: temperature

A: An I-beam made of 4140 steel is heat treated to form tempered martensite. It is then welded to a…

Q: 5.8 Show that for temperatures well below p, the mean free path of a phonon can be expressed as f…

A:

Q: 1. What are the normal use or uses of this product or component? What are the normal operating…

A: Given questions: 1. What are the normal use or uses of this product or component?    What are the…

Q: From the following compressibility factor data for CO2 for CO₂ at at 150°C determine the fugacity…

A: Compressibility factor is taken to be equal to unity (one) for an ideal gas. Compressibility factor…

Q: Q/ In figure below, if the friction force between the cable and the pulley is negligible, determine…

A:

Q: If a force of 30 N is required to move a mass of 35 kg on a flat surface horizontally at a constant…

A:

Q: A meter stick balances horizontally on a knife-edge at the 50.0 cm mark. With two 4.78 g coins…

A:

Q: A- An air conditioner compressor 134a at 4 bar, 20 °C and 6 m³/min which is steadily compressed to…

A:

Q: Four forces are exerted on the eyebolt as shown. If the net effect on the bolt is a direct pull of…

A:

Q: Two ships leave the same port at the same time. Ship A sails on a course of 125°T at 18 knots while…

A:

Q: he buoy shown in (Figure 1) is made from two omogeneous cones each having a radius of 1.5 ft. Figure…

A: h=0.8ft r=1.5ft

Q: The Mach number at the exit is ●●●●●●● Air at stagnation pressure of 600 kpa and stagnation…

A:

Q: Cantilever beam loaded as shown in fig., draw the shear force diagram and bending moment diagram. 20…

A:

Q: B. Pure Substance Processes 1. A prototype boiler that contains 5 kg of saturated steam at a…

A:

Q: ssume that we disturb an undamped system from equilibrium. Sketch and explain a system's time…

A: Explaining a system's time response when we disturb an undamped system from equilibrium.

Q: In the figure, one end of a uniform beam of weight 130 N is hinged to a wall; the other end is…

A: Given dataWeight of beam = W = 130 Nθ = 34°

Q: A hydroelectric plant gets water from a dam at the rate of 100 cubic meters per minute to generate…

A:

Q: What is the second derivative of f(m) = 53 ? m³

A: Given function is, f(m)=5m3        =5×m-3 Differentiate above function w.r.t. m, f'(m)=ddmf(m)…

Q: Q/ For the mechanism shown below, ? compute the magnitude of the force (F) required to break contact…

A:

Q: n a power plant, the steam from the boiler reaches the turbine at a temperature of 700 °C. The spent…

A: Given: The maximum temperature of the cycle , TH = 700°C=973K The minimum temperature of the cycle ,…

Q: 3. Air undergoes a process from 98.1 N/cm², 120 °C to 19.62 N/cm² and -15 °C. Calculate the…

A: The polytropic index of the overall process: n = 1.35385

Q: 1. AB X 2. A+B=X 3. X=A 4. ABC=X Page | 4

A:

Q: Involute gears, gear A with 10 teeth, turning clockwise at 160 RPM drives gear B which turns at 100…

A:

Q: Draw the schematic diagram for each of the following Boolean Expressions: 1. AB = X 2. A + B = X 3.…

A:

Q: Q/ The force in the member (CA) is 12m 50 ку 490.50 N 500.44 N 200.12 N 2550 N 5m

A: None of the options are right. but Solution is 100% right.

Q: The 55-kg cylinder is suspended from a clamping collar at C which can be positioned at any…

A: cable length = 12 m distance between the supports A and B = 10 m mass of the cylinder (m) = 55 kg

Q: Q5. A 3 kw wasted energy (as a heat) from a fired system at temperature of 80°C is to be used to…

A:

Q: 1 m 0.3 m 70° m 4 kN 0.5 m 1.5 m 15 kN m 10 KN 6 kN 0.3 m Replace the three horizontal forces and…

A:

Q: The imaxis sected to the system of forces as shown in the following fique The tas is supported 600…

A:

Q: 7-In isentropic subsonic flow in convergent nozzle the velocity increase with the decreasing of the…

A:

Q: Use the superposition method and determine: 1. The deflection of the beam at point C Important: It…

A:

Q: SI/USCS Units) In a Brinell hardness test, a 1500-kg load is pressed into a specimen using a…

A:

Q: A cylinder is made of steel plate is intended to be used as a container for compressed air. The…

A:

Q: The state of strain at the point on the pin leaf has components of € = 200(10-6), y = 180(10-6), and…

A: Introduction: When an elastic body is subjected to external forces, material locations inside the…

Q: Determine the minimum diameter of a 10-meter-long aluminum cantilever rod that can support the…

A: given; length of cantilever beam(l)=10mmaximum deflection at free end(δmax)=0.01m

Q: A 15 cm outer diameter steam pipe is lagged to 25 cm diameter with magnesia of thermal conductivity…

A: One-dimensional heat transfer through a simple or composite body exposed to convection from both…

Q: The truss is subjected to the system of forces as shown in the following figure. The truss is…

A:

Q: 1. AB=X 2. A+B=X 3. X=A 4. ABC=X 5. AB+CD=X 6. AB+A=X Page | 4

A:

Q: Find the acceleration of the body from t=12s to t=15s

A:

Q: If feedwater is supplied at 50 degrees Celcius, a boiler generates 10,000 kg/hr of steam at 98%…

A:

Q: A- An air conditioner compressor receives refrigerant 134a at 4 bar, 20 °C and 6 m³/min which is…

A: Given: Inlet pressure to the compressor→Pi=4 bar=400 KPa Inlet temperature of the…

Q: There is a flow of air that circulates over a flat plate that is used to store a food product at a…

A: Given data: Ts=95°CT∞=25°CV=2.5 m/s Need to determine the heat loss from the plate if the air flows…

Q: Q1 A round bar is subjected to a rotating force. State what type of stress is induced in the bar and…

A:

Q: jet

A: Let vane is symmetrical then; θ0=θ1=θ 180-2θ=150θ=15o…

Q: 0 1 m 0.3 m 70° 1 m 4 kN 0.5 m 1.5 m 15 kN m 10 KN 6 KN 0.3 m Replace the three horizontal forces…

A:

Q: Q3. Determine the gauge pressure at point A in the figure shown. Is it higher or lower than…

A: The gauge pressure at point A is PA,gauge = 12281.62 Pa (vacuum). It is lower than Patmosphere.