4. A two-bus power system bus admittance matrix is bus -j9 j3 j3 -j8 53] P per unit. Suppose prefault voltage is 1.05 per unit and prefault load current is neglected. (1)Draw equivalent circuit of two-bus power system according to bus admittance matrix; (2) Determine the 2x2 positive-sequence bus impedance matrix Zbus (3) For a bolted three-phase short circuit at bus 1, use Zbus to calculate the subtransient fault current; (4) voltages at buses 1 and 2 during the fault.

4. A two-bus power system bus admittance matrix is bus -j9 j3 j3 -j8 53] P per unit. Suppose prefault voltage is 1.05 per unit and prefault load current is neglected. (1)Draw equivalent circuit of two-bus power system according to bus admittance matrix; (2) Determine the 2x2 positive-sequence bus impedance matrix Zbus (3) For a bolted three-phase short circuit at bus 1, use Zbus to calculate the subtransient fault current; (4) voltages at buses 1 and 2 during the fault.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter7: Symmetrical Faults

Section: Chapter Questions

Problem 7.18P

See similar textbooks

Similar questions

Figure 5 shows a single-line diagram of a three-bus power system. Power flow input data are givenin Tables 1 and 2. (a) Determine the Ybus Matrix (b) Use Gauss-Seidel method to compute V2(1) and V3(1), the phase voltages at bus 2 and 3 after the first iteration. Use zero initial phase angles and 1.0 per-unit initial bus voltage magnitudes.
From, the given [Ybus] below, Find a). Eliminate firstly node 3 and then node 4 by using Kron Reduction method,calculate the new [Ybus]. b). Find the new [Z]. c). Find the equivalent circuit of the new 2-bus system.
-The voltage magnitude and phase angle are the quantities to be determined after load flow analysis for ............bus. -The total reactance of the transmission system is reduced by installing a series capacitor. Select one: True False
Draw the reactance diagram of the system whose single line diagram is given below and load flow in the system.the bus admittance matrix required to perform the analysis without using a numerical value.remove symbolically
Determine the bus voltages at buses 2 and 3 after 1st iteration using GS method. Take the acceleration factora=1.6
A single-line diagram of a four-bus system is shown in fiugre. Equipment ratings and per-unit reactances are given as follows.Machines 1 and 2: 100 MVA 20 kV; X1= X2 = 0.2; X0= 0.04 Xn= 0.05 Transformers T1 and T2: 100 MVA 20Y/345Y kV; X1 = X2 = X0 = 0.08. On a base of 100 MVA and 345 kV in the zone of the transmission line, the series reactances of the transmission line are X1 = X2 = 0.15 and X0=0.5 per unit. (a) Determine the bus impedance matrix for each of the three sequence networks. (b) Assume the system to be operating at nominal system voltage without prefault currents when a bolted single-line-toground fault occurs on phase A at bus 3. Compute the fault current, the current out of phase C of machine 2 during the fault, and the line-toground voltages at the terminals of machine 2 during the fault. Total detailed answer is needed. The figure is attached.
In fast decoupled method of load flow study, the sparsity feature of Y bus minimizes the____________________________________________ requiremen
Considering two parallel three-phase circuits that are close together, when calculating the equivalent series-impedance and shunt-admittance matrices, mutual inductive and capacitive couplings between the two circuits can be neglected. True False