Answered: 4. Compare the deflection values for…

4. Compare the deflection values for both cases given below, Which one is safer if the limit is L/360? Why? What is behind the difference for two cases?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A rectangular cantilever beam 60 mm wide by 100 mm deep is 2 m long and with E = 200 GPa. A 40 kg…

A: In general, there are three types of loading, i.e., gradually applied loading, suddenly applied…

Q: 1. A cylindrical rod is loaded at A incrementally. It has a length of 1.6 m. , is 28 mm in diameter…

Q: A rod has been axially loaded. The axial deflection of the rod is measured to be 0.8 mm. A reduction…

A: Given data : Initial diameter=d Change in diameter=δY Axial length of rod=L Change in length of…

Q: A simply supported circular steel plate of diameter 1 m and thickness 50 mm is subject to an…

Q: Consider the maximum allowable vertical deflection of point D. Calculate the corresponding angle of…

A: Given data: From previous part, ◆ The torque acting on the shaft at B: T = 111600 lb•in ◆ The total…

Q: 1. Was there good agreement between the theoretical predictions (dthe) and the experimentally…

Q: The Flexor loading micrometer will be used to load the beam. Calculate the deflection equired to…

A: On substituting the given values of 'L', 'E' in the given equation of deflection we get y…

Q: A cylindrical rod is loaded at A incrementally. It has a length of 1.6 m. , is 28 mm in diameter and…

Q: 2 Find the equation of deflection (under the uniformly distributed load) and calculate the maximum…

Q: Derive the following equation of maximum deflection using double integration method

A: Dear student, According to the guidelines I am allowed to answer only one…

Q: How is the flexure formula derived on the basis of assuming the beam to be prismatic?

A: Draw the cross-section of the prismatic beam with a point load in the end.

Q: For a beam with a length of 200 mm, a width of 20 mm and a height of 3 mm, calculate the maximum…

Q: The frame shown in Figure 5 is unbraced, and bending is about the x-axis of the members. All beams…

A: 1. Calculate the ratio of column stiffness to girder stiffness at each and of column AB by using the…

Q: Does the distance between the supports effects the deflection measured? Why?

A: Solution:

Q: Q2 find the deflection equation for the simply supported with uniform distribution load using…

Q: PLEASE SHOW THE FBD/s 7. Write the moment equation for the entire beam. Place your answer in a box.…

A: The free body diagram of the given beam is here, RAH and RAV are the horizontal and vertical…

Q: Read the question carefully and give me right solution with clear calculations. A cantilever beam…

Q: A cantilever of flexural rigidity 200 N-m? is loaded as shown in the figure. The deflection at tip…

A: Given:Flexural rigidity, EI=200 N-m2

Q: A cylindrical rod is loaded at A incrementally. It has a length of 1.6 m. , is 28 mm in diameter and…

Q: Bending induced tensile yield failure.

A: WE will calculate limiting value of force F

Q: 10) In the figure shown, the deflection of mercury is initially 250mm. If the pressure at a is…

A: The pressure difference between the point A and point B can be determined as,

Q: Problem 04.077. Determine the deflection of an angled bar using Castigliano's theorem Using…

Q: 1. A cylindrical rod is loaded at A incrementally. It has a length of 1.6 m. , is 28 mm in diameter…

Q: Figure 2 Compute the stiffness matrix D-1 for D in (a) by using Cramer's rule. List the forces…

Q: A 1m span beam carrying UDL of 384N/m whose is maximum deflection at centre 5/EI -5/EI 7/EI…

Q: Continue with Questions 1-3 above. What is the deflection at point C. (It will be easier to use…

Q: (b) L/3 P↓ ↓ L/3 L/3 Draw the deflection of the beam. Where would you expect the maximum deflection?…

A: Given: There are two loads as P are acting apart L/3 distance and of same quantity. Hence from the…

Q: Calculate the slope and deflection at the free end of the cantilever bea figure using Method of…

A: For the given slope:

Q: Write the differential equation for the deflection curve?

A: Consider a cantilever beam on which a point load P is acting at free end. The diagram of the…

Q: A cantilever beam, 850 mm long, carries a uniform load of 5 kN/m. What is the value of Ely at the…

A: GIven: Cantilever beam w=5 kN/m L=850 mm TO determine: EIy at free end

Q: Calculate the deflection curve v(x) for Problem 1. 1. Consider the following composite LEHI…

Q: Find the Deflection using conjugate beam method.

A: The free-body diagram of the beam is shown below, ∑Fy=0RA+RB-10×2=0RA+RB=20 ...........…

Q: Find the shaft diameter in Fig. 2 if the allowable deflection is 1 mm. The values for F 60 KN, and…

A: F = 60 kN Allowable deflection = 1 mm Assume E = 210 Gpa

Q: What will the shear force and bending moment diagram look like for the beam subjected to a point and…

A: Find Choose the correct SFD and BMD diagram for the given beam.

Q: Determine the vertical and horizontal deflec- tions of the end B due to load P of the thin curved…

A: The vertical and horizontal deflection of the end B of the thin curved bar of uniform cross section…

Q: Initial length is 100 cm, final length is 102 cm. Load P = 10.000 N. Find deflection, strain rate,…

Q: 1. A cylindrical rod is loaded at A incrementally. It has a length of 1.6 m. , is 28 mm in diameter…

Q: 7) Are deflections for steel beam design determined with unfactored loads to compare to the code…

A: The design of steel beam deflections

Q: The angle of rotation at the maximum deflection is: a. 0.5 b. 0 c. 2 d. 1

A: It is required to choose correct answer

Q: Explain about Deflections of beams by double integration method with example ؟

Q: only, solve carefully, include the units in every step and draw the diagram. Thanks! A force…

Q: The static transverse deflection of simply supported beam with a uniformly distributed load (UDL) is…

A: Answer is (b) 5wl4 /384EI

Question

need correct and urgent

4. Compare the deflection values for both cases given below, Which one is
safer if the 'limit is L/360? Why? What is behind the difference for two cases?
Commentate findings, (E= 20000 MPa)
your
%3D
12 삐m
lu kN/M
2)
60 cm
30 cm
구 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1a

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Quality Assurance, Process Planning, and Quality Control

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

In the figure shown below, the deflection of mercury is initially 250mm . If the pressure at A is increased by 33kpa , while maintaining the pressure at B constant, what will be the new mercury deflection? Pls answer and explain in detailed
A steel rod with a diameter of 2 inches, is subjected to a torque of 50000lb-ft. If the modulus of rigidity is G=12x10^6 psi for steel rod, determine the deflection per unit feet of the steel rod in degrees per unit foot.
need help calculating displecment / deflection using formula: W*L3 / 48*E*I W: 0,5,10,15,20,25 (N) L3: 0.4m E: Modulus of elasticity of Aluminum I: moment of Inertia: 1.51 x 10^-9 The cross section of material is aluminum tube 12.7mm x 9.5mm
A hollow shaft with outside diameter of 14 cm and wall thickness of 0.8 cm transmits 400 KW at 400 rpm. What must be the angular deflection if the length is 5 m? G= 12 Mpsi
MENG222 STRENGTH OF MATERIALS P=1000
Calculate first the formula and then the value of the angle of rotation and deflection of the beam with a length of 3m at the point C. L = 2.1m , A= 0.9m E=210GPa I=119x106mm4
Pls answer thank you! A helical spring having squared and ground ends has a total of 20 coils and its material has modulus of elasticity in shear of 78.9 Gpa. If the spring has an outside diameter of 10.4 cm and a wire diameter of 0.625 cm, compute the deflection in the spring due to a load of 50 kgs.
The bar shown in the figure is composed of a 2-cm-diameter aluminum section, a 3-cm-diameter brass section, and a 2-cm-diamter steel section. Calculate the deflection of each of the metal sections and the total deflection of the whole bar.
A) If the modulus of elasticity of the material is E = 1870 MPa , what is Poisson's ratio? B)The block is subjected to a force V that produces a deflection of Δ = 0.15 cm . What is the applied force?
For the simply supported beam carrying the concentrated load P = 268 N at its midspan, determine the magnitude of the maximum displacement (in mm) if d = 1.51 m, E = 11.77 GPa , and I =1679930mm4. NOTE: PLEASE ANSWER IT CORRECTLY. IF YOU ARE NOT SURE ABOUT THE ANSWER, PLEASE SKIP THE QUESTIONPLEASE BOX THE FINAL ANSWER(S)THANK YOU! image below for reference
Locate the position of the maximum deflection. Box your answer.What is the deflection at 2 meters from the left end. Box your answer.What is the slope of the elastic curve at point C? Box your answer.
A materila has a modulus of elasticity (E=17 Mpa) and a poissons ratio of 0.27. what is the approximate value of the shear modulus, G?