4. Design a welded connection to resist the loading shown below (service load). A double angle tension member, 2 L5x5x5/16, is connected to a 3/8 inch thick gusset plate with fillet welding. Fy = 50 ksi for the angles and Fy = 36 ksi for the gusset plate. Compute the size and length of welding on the side of angles based on LRFD and indicate the information on the sketch. %3D

4. Design a welded connection to resist the loading shown below (service load). A double angle tension member, 2 L5x5x5/16, is connected to a 3/8 inch thick gusset plate with fillet welding. Fy = 50 ksi for the angles and Fy = 36 ksi for the gusset plate. Compute the size and length of welding on the side of angles based on LRFD and indicate the information on the sketch. %3D

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter7: Tubing And Piping

Section: Chapter Questions

Problem 14RQ: When soldering, a flux is used to A. minimize oxidation while the joint is being heated. B. allow...

See similar textbooks

Similar questions

An angle iron made of AISI 1040 CD steel is welded to metal as shown and loaded with a dynamic load varying between +40kN and +60kN. E70XX (Sut = 482MPa, Sy = 393MPa) will be used as the welding electrode. Find the factor of safety of the weld zone. Note: that both static and dynamic loads are applied to the source.
A mild steel ammonia receiver is a cylinder 2 m in diameter with a pressure load of 1250 kPa and a design stress of 65 MPa. The lap welding tensile strength is 450 MPa and the weld -joint efficiency is assumed to be 100%. Compute the bursting pressure of the receiver in kN/m².
A bracket to be welded into a steel channel using E-60 electrode 345 Mpa) Two welding sets are suggested as shown in Fig. (1)Based on maximum shear stress failure theory and safety factor of (2.5) (a) Find the weld size for each set. (b) Which set would you recommend A or B ?
The unit melting energy for a certain sheet metal is 10J/mm^3 .The thickness of each of the two sheets to be spot-welded is = mm. To achive required strength, it is desired to form a weldnugget that is =7 mm in diameter and 3.5 mm thick. The weld duration will be set at 44 sec .If the electrical resistance between the two surfaces is 144 micro-ohms and only one half the electricity generated will be used to form the weld nugget Determine the minium current level required in this operation
Calculate the heat input during the arc welding process, if the voltage is 32 volts, current is 120 amperes, the length of the weld is 94mm and the time to complete the weld 33 secs. 1-Speed S= 2-Heat Input (Watts)=
What stresses occur in the welding joints given in the picture. Extract the formulas.
QUESTION 20 Below is an image showing two 4 mm thick sheets joint together using double rivets. If the rivets were made of st
The design below is used for a bridge construction. All parts of the assembly are made of ASTM A36 steel and are welded with an E60 electrode. Under these conditions, the minimum size weld, according to table 20-4, should be: 5/16 3/16 3/8 1/4 1/2 5/8
Dynamic forces F1 = 4000N and F2 = 6000N are applied to the welded part shown in the figure as shown below. For dynamic forces, both dynamics are synchronized, and when the force in the y-axis direction is downward, it is on the right in the x-axis direction. When the force is up, the other force is on the left. The welded part is made of 1018 HR steel, 10 mm thick. a) Safety factor for welding? b) Calculate the safety factor for the base metal. (Electrode type for question is E9010.)
The below Figure Q1 shows an aluminium alloy sheet metal requires to be spot welded. In order for the weld to achieve its required strength, it has to be 2mm thick and the weld duration will be set at 0.3 sec. If it is assumed that the electrical resistance between the surfaces is 160 micro-ohms, and that only 40% of the electrical energy generated will be used to form the weld nugget (the rest being dissipated into the work), determine: a) The heat energy generated at the source b) The minimum current level required in this operation c) Assuming the heat transfer factor is 0.9, what would the melting factor be? d) The power density of the process, and comment on the value.
A GTAW operation is performed on low carbon steel, whose unit melting energy is 10.3 J/mm3. The welding voltage is 22 volts and the current is 135 amps. The heat transfer factor is 0.7 and the melting factor is 0.65. If filler metal wire of 3.5 mm diameter is added to the operation, the final weld bead is composed of 60% volume of filler and 40% volume base metal. If the travel speed in the operation is 5 mm/sec, determine (a) cross-sectional area of the weld bead, and (b) the feed rate (mm/sec) at which the filler wire must be supplied.
An RSW operation is used to join two pieces of sheet steel having a unit melting energy of 8369.85 J/cm3. The sheet steel has a thickness of 0.3125 cm. The weld duration will be set at 0.25 sec with a current of 11,000 amp. Based on the electrode diameter, the weld nugget will have a diameter of 0.75 cm. Experience has shown that 40% of the supplied heat melts the nugget and the rest is dissipated by the metal. If the electrical resistance between the surfaces is 130 micro-ohms, what is the thickness of the weld nugget assuming it has a uniform thickness?