Below is an image showing two 4 mm thick sheets joint together using double rivets. If the rivets were made of steel with ultimate and yield shear strengths of 500 MPa and 315 MPa respectively, and the sheets were made of Aluminium with bearing strength of 50 MPa, what would be the minimum rivets' diameter required for a safe and functional operation of the joint if the pulling force from each side is 8 kN. 8 kN 8 kN nton

Below is an image showing two 4 mm thick sheets joint together using double rivets. If the rivets were made of steel with ultimate and yield shear strengths of 500 MPa and 315 MPa respectively, and the sheets were made of Aluminium with bearing strength of 50 MPa, what would be the minimum rivets' diameter required for a safe and functional operation of the joint if the pulling force from each side is 8 kN. 8 kN 8 kN nton

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.5.1P: The rails of a railroad track are welded together at their ends (to form continuous rails and thus...

See similar textbooks

Similar questions

A single riveted lap joint is made in 15 mm thick plates with 20 mm diameter rivets. Determine the strength of the joint, if the pitch of rivets is 60 mm. Take σt= 120 MPa; τ = 90 MPa and σc= 160 MPa.
The bolted connection illustrated below comprises one bolt and two plates. The bolt, which has a diameter of 20 mm, is threaded through a 22- mm diameter hole in both plates. The shear stress of the bolt is 78,000 MPa. Based on this information, determine the following What is the largest force F that can be placed on the joint without shearing the bolt? what is the normal stress, at the gross section area, in each plate? what is the normal stress, at the net section area, in each plate? what is the bearing (or contact) stress between the bolt and each plate?
Hexagonal nuts for 6.25mm diameter bolts have a height of 5.5mm. If the ultimate strength of the nut material in shear is 103MPa, what is the most nearly the maximum allowable shear force on the nut thread using a safety factor of 5?
A 20 mm diameter rivet is used to fastened two 25 mm thick plate. If the shearing stress is 80 Mpa, what tensile force applied each plate to shear the bolt?
(D) Seven circular cross-section rivets (Dia.=16 mm) are used to fix a lap joint of steel plates under single shear action. If the rivets are made from Aluminium (E=80 GPa) and the plates under tension of 15 kN. Solve this problem to show weather this joint is safe or not. Suppose all the rivets have equal load share.
1. A flanged bolt coupling consists of 20-mm aluminum bolts evenly spaced around a bolt circle 30 cm diameter and 12-mm steel bolts on a concentric bolt circle 20 cm in diameter. The allowable shearing stresses are 42 MPa in the aluminum and 62 MPa in the steel. What should be the minimum number of aluminum bolts if there are four steel bolts and the power applied is 760 kW at 600 rpm? Use Gal = 28 GPa and Gst = 83 GPa. 2. A torque of 1880 lb-ft is applied to the tube that has an elliptical shape with major and minor outside diameters of 6 in. and 3 in., respectively. Determine the minimum wall thickness so as not to exceed a shear stress of 8 ksi. Kindly answer please. I need ASAP thank you
Can someone please explain the step-by-step process of this. Thank you so much! The d = 12-mm-diameter solid rod passes through a D = 17-mm-diameter hole in the support plate. When a load P is applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b = 13 mm. The rod head has a diameter of a = 24 mm, and the head has a thickness of t = 9 mm. The shear stress in the rod head cannot exceed 130 MPa, the punching shear stress in the support plate cannot exceed 85 MPa, and the bearing stress between the rod head and the support plate cannot exceed 130 MPa. Determine the maximum value of Pmax that can be supported by the structure.
Problem 2 only, solve carefully, include the units and dra the diagram. Thanks! A 3/4 inch diameter rivet is used to fastened two 25 mm thick plate. If the shearing stress of rivet is 80 Mpa, A. What tensile force applied each plate to shear the bolt, pounds?B. What bearing stress that the bolt can withstand, MPA
write legibly Indicate all necessary FBDs, concepts and formulas needed in the solution. The lap joint shown is fastened by 6 − 20mm diameter rivets. Assuming that P = 200KN, determine (a) the shearing stress in each rivet, (b) the bearing stress in each plate 25mm thick and 100mm wide. Assume that the axial load P is distributed equally among the 6 rivets, and the diameter of hole is 22mm. See figure 102.
For the lap joint shown in figure. 1. Determine the maximum safe load P which may be applied if the shearing stress in the rivets is limited to 60 MPa. 2. Determine the safe load P which may be applied if the bearing stress of the plate is limited to 110 MPa. 3.Determine the safe load P if the average tensile stress of the plate is limited to 140 MPa.
Question 1: Taking the safety factor as 2 for the loading condition shown in the figure, we can calculate the maximum axial force (P) that can be applied. d=100mma) On the theory of maximum normal stressb) Maximum shear stress theoryc) Calculate according to the maximum strain energy theory.The structure is made of steel and the proportional limit is 250 MN / m2 in pressing and drawing, and 140 MN / m2 in shear. The elasticity module of the material is 200 GPa and the Poisson's ratio is 0.3. d=100mm
Read with understanding and solve the following problem carefullyand honestly: Write your solution on a separate sheet of paper.1. In the figure, assume that a 20-mm diameter rivet joins the plates which are100 mm wide.a. If the allowable stresses are 140 MPa for bearing in the plate material and 80MPa for shearing of the rivet, determine the minimum thickness of each plate.(Ans. t = 9 mm) b. Under the conditions specified in part (a), what is the largest average tensilestress in the plates? (Ans. δt = 34.91 MPa)