4. If w-30 kN/m and L=10m, the cross section is made-up of two I-beams shown, determine the following: a. Maximum bending stress b. Spacing of the bolts if the shear force resisted by each bolt is 30 kN (Hint: Maximum moment occurs at midspan; Maximum Shear is the highest magnitude in the shear diagram) 210 mm 24 mm 15 mm 230 mm L 24 mm

4. If w-30 kN/m and L=10m, the cross section is made-up of two I-beams shown, determine the following: a. Maximum bending stress b. Spacing of the bolts if the shear force resisted by each bolt is 30 kN (Hint: Maximum moment occurs at midspan; Maximum Shear is the highest magnitude in the shear diagram) 210 mm 24 mm 15 mm 230 mm L 24 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The horizontal shaft AD is attached to a fixed base at D and is subjected to the torques shown. A 44-mm-diameter hole has been drilled into portion CD of the shaft. The entire shaft is made of steel for which G = 77 GPa. 1. Calculate the torque in segment CD in N.m. 2. Calculate the torsional shear stress on the surface of segment BC in MPa. 3. Calculate the angle of twist of segment AB in degrees. 4. Calculate the angle of twist of point A relative to point D in degrees.
The frame (Figure 1) has dimensions H1 = 4 m , H2 = 3 m , L1 = 5 m , and L2 = 10 m and supports two lateral loads P1 = 10 kN and P2 = 12 kN . a) Use the portal method to determine the shear at J. VJ = ? b) What is the vertical reaction from the ground on the base of the column at AA? Let a positive reaction be pointing upward. Ay = ? c) What is the vertical reaction from the ground on the base of the column at B? Let a positive reaction be pointing upward. By = ?
Determine the shear stress (in Mpa) in the 20.75-mm-diameter pin at A that support the beam if P = 28.96 kN, a = 2.12 m, and b = 5.72 m. Round off the final answer to three decimal places.
Given: Maximum positive shear = 3960 N Maximum negative shear = 5640 N Maximum positive moment = 20700 N-m Maximum negative moment = 2400 N-m Location of maximum shear from the left end of beam = 19 m Location of maximum moment from the left end of beam = 14 m Determine the maximum bending stress (in MEGAPASCALS on the beam) given the cross-section on figure. Note: Measurements in figure is in millimeters. Kindly Draw the Shear and Moment Diagram or FBD if necessary. Compute for all of the necessary elements, Include the proper units, use the proper formula and round-off all the answers and final answers to 2 decimal places.
(i) A tie bar is 2.5 m long, has a circular cross section of 50 mm in diameter and is subjected to a force of 250 kN. Given that Young’s Modulus E = 209 kN/mm2 and Poisson’s Ratio ν = 0.3 calculate the change in volume of the bar when loaded. (ii) Draw the shear force and bending moment diagrams for the cantilever beam shown in the image attahced clearly indicating all significant points.
(a) Determine the reactions at the supports and draw the bending moment diagram for the following structures. (b) Repeat problem (a) if there are a support movement of A to left by 10mm and a support settlement at D by 12mm. Given E=200GPa, I=107mm4 .
determine the shear force and bending moment at point C in the figure. Given the details, Point 1 - 3kN/m Point 2 - 6kN/m Point 3 - 3kN/m A-B = 4m B-C = 2m
consider the moment-resisting frame. Use the portal method of analysis. Use P2 = 4 kips What is the shear force in the bottom beams (absolute value)? P1 = 2 kips What is the shear force in member EH (absolute value)? h = 11' What is the horizontal reaction at H (absolute value)? b = 25' What is the bending moment in the top beams (absolute value)? (please ignore black markings) What is the vertical reaction at I (tension positive)?
Calculate the normal stress due to flexure at the flange level to web Interface at A. Ixx= 1,241 in^4. Bending moment (M)= 350 ft-kips. Shear (v)= 80 kips.
(a) Determine the reactions at the supports and draw the bending moment diagram for the following structures. (b) Redo problem (a) by using the bending moments over support A and B as the redundant forces. (c) Repeat problem (a) if there are support settlements of 8mm, 5mm and 2mm at A, B and C respectively. Given E=200GPa, I=107mm4 .
Given: Maximum positive shear = 387.50 kN Maximum negative shear = 602.50 kN Maximum positive moment = 1970.65 kN-m Maximum negative moment = 1480 kN-m Location of maximum shear from the left end of beam = 22 m Location of maximum moment from the left end of beam = 15.23 m Determine the maximum bending stress (in MEGAPASCALS on the beam) given the cross-section on figure. Note: Measurements in figure is in millimeters. Kindly Draw the Shear and Moment Diagram or FBD if necessary. Compute for all of the necessary elements, Include the proper units, use the proper formula and round-off all the answers and final answers to 2 decimal places.
A steel bar having cross-sectional areaA=1200mm2 is compressed by an axial loadP=53 kN.Determine the average normal and shear stressesacting on aninclined sectionaa cut through the bar at angleα=250.(Point K is a fixed support) A=5, B=3, C=8