4. In the following, which one is the water-based fluid?(single choice)A.Polymer drilling fluidsB.Synthetic-based drilling fluidsC.Oil-based drilling fluidsD.Form/Mist drilling fluids5. In the following, which one is not the properties of drilling fluids?(single choice)A.DensityB.ViscosityC.MassD.Filtration6. Regarding the fluid models, which one is incorrect?(single choice)A.plastic viscosity µo = lim -Y-00 YB.apparent viscosity Ha =C.Power law fluid model 7 = kyD.Bingham plastic model t = To + HooY 1. Regarding the circulating system, which one is correct?(single choice)A.Drilling fluid flow path: mud pit-mud pump-standpipe+swivel-kelly-drill pipe-drill collar drill bit-annulus+solid control system-mud pitB.Drilling fluid flow path: mud pit+mud pump-standpipe-swivel-kelly-drill bit-drill pipe-drill collar*annulus*solid control system-mud pitC.Drilling fluid flow path: mud pit-mud pump-swivel-kelly-drill pipe-standpipe-drill collar-drill bit-annulus+solid control system-mud pit2. In the following, which one is not the correct function of drilling fluids? (singlechoice)A.Control wellbore pressureB.Cuttings transportC.Pollute the environmentD.Transmit hydraulic horsepower3. For the function of control subsurface pressure, what are the major influencingfactors? (multiple choice)A.Mud weightB.Flow rateC.Rheological propertiesD.Filtration properties

Q.no. 4:- Polymer drilling fluids Polymer drilling fluid, also known as polymer fluid, is a drilling…

4. In the following, which one is the water-based fluid?(single choice) A.Polymer drilling fluids B.Synthetic-based drilling fluids C.Oil-based drilling fluids D.Form/Mist drilling fluids 5. In the following, which one is not the properties of drilling fluids?(single choice A Density

4. In the following, which one is the water-based fluid?(single choice) A.Polymer drilling fluids B.Synthetic-based drilling fluids C.Oil-based drilling fluids D.Form/Mist drilling fluids 5. In the following, which one is not the properties of drilling fluids?(single choice A Density

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Use F = 35 kN and L = 12 m Compute for the 3 support reactions a.

A: We have to determine the value of 3 support reactions as per the given data in the question like F =...

Q: SITUATION 9: For Items 28-33. 3 k/ft 2 k/ft im A в с -10 f-10A 15 ft- El = constant 28. What is the ...

A: Given,

Q: How do Flow Irregularities impact certain pipeline operations and what are their advantages and disa...

A: Concept- Flow irregularities- These are the issues that arise while the fluid flows in the pipelines...

Q: 7. The steel shaft is formed by attaching a hollow shaft to a solid shaft. Determine the value of to...

A: We have to determine the value of torque T that can be applied to the ends of the shaft without exce...

Q: A ball on the end of the string is revolved at a uniform rate in a vertical circle of radius 72 cm. ...

Q: Shear and Moment Diagram: 600 lb/ft 1200 lb - ft 6 ft 4 ft 4 ft Point of Zero Shear: Value of Moment...

Q: The tank shown rolls along a level track. Water received from a jet is retained in the tank. The tan...

A: Given,

Q: A square footing is to be used to support a 300mm by 300mm RC column loaded with 500 kN dead load an...

Q: anti-vibration shear mount No. 2. The 16 mm by 22 mm by 25 mm rubber blocks shown in Figure No. 2 ar...

A: Volume of the block =16 x 22 x25 mm P= 285N δ=5mm

Q: A ball on the end of the string is revolved at a uniform rate in a vertical circle of radius 72 cm. ...

Q: . Determine the reactions and draw only the bending moment diagram for the frame shown in the figure...

A: ###Using force method ## Reaction Determination and BMD ####

Q: To determine the daily evaporation at Taal lake, a USWB Class A evaporation pan is maintained. The w...

A: Given data, USWB Class A evaporation pan is maintained. The water level in the pan is 200mm at the ...

Q: 50 m length of tape is of standard length at temperature of 50.76°C. What would be the error in the ...

Q: -b- d, b = 250 mm d, = 200 mm d2 = 100 mm d,

A: Given,Net loss=10%Force applied at X=750 kNb=250mmd1=200mmd2=100mm

Q: A column is subjected to a load through a bracket as shown in the figure. 15 cm- P= 10 kN %3D 10 cm ...

Q: Y1 V2

Q: In a pre-stress concrete beam section, 10% and final pre-stressing force applied at X is 750kN. The ...

Q: A column 500 mm x 500 mm square is supported by a 3.5 mx 3.5 m isolated spread footing. The column c...

A: shear stress, force tending to cause deformation of a material by slippage along a plane or planes p...

Q: and compute the maximum and minimum compressive stresses at the base. Neglect hydrostati uplift.

Q: A ball of mass 5kg and a block of mass 1a kg are attached by a lightweight cord that pasSses over a ...

A: Acceleration: The rate of change of velocity with respect to time is known as Acceleration. Accelera...

Q: steel cylinder has a specific weic as a plug for the 1 ft long slot in

Q: 4.31 As a valve is opened, water flows through the diffuser shown in Fig. P4.31 at an increasing flo...

Q: Three pipes steadily deliver water at 20°C to a large exit pipe in Figure 1. The velocity V; = 5 m's...

A: Given, In pipe (1), Diameter = D1= 4cm V1=? In pipe (2), Diameter= D2 = 5cm = 0.05m V2=5m/s In ...

Q: A 12 mm thick plate is connected to two 8 mm thick plates, on either side through a 16 mm diameter p...

Q: The angle between the prolongation of the preceding line and the forward line of a traverse is calle...

Q: Contour map 1- Draw contour lines with C.I = 100 m. 2- Describe the topography of the area. 3- Draw ...

A: 1. The contour lines are drawn below:

Q: If the 580-kg drum has a center of mass at point G, determine the horizontal component of force acti...

A: Given Data -

Q: A vertical 150-mm-diameter pipe leaves a water tank that has a surface elevation of 12m. Between the...

Q: INSTRUCTIONS: COPY THE GIVEN TRUSS AND SOLVE FOR THE MEMBER 12 FORCES: АВ. АС, ВС, BD, BE, BF, CF, 1...

Q: 3. A stratum of normally consolidated clay is 25 feet thick and the water content is measured as 50%...

Q: 1. A block of wood having a volume of 0.034m and weighing 300N is suspended in water as shown. A woo...

Q: Determine the maximum allowable volume flow rate in L/min that can be carried through a standard ste...

A: We have to determine the value of maximum allowable volume flow rate in L/min that can be carried by...

Q: The table below shows the field measurements for a traverse A, B, C, D, E, if the Azimuth of AB = 29...

Q: Q1) A rural 4-lane highway is to be built between two towns. Select the binder performance grade to ...

A: We have to select a select the binder performance grade to meet the Super pave criteria for a reliab...

Q: Use the moment area method and determine the slope just to the left and just to the right of the pin...

Q: For the truss loaded as shown, determine the forces in members CD, CJ and IJ. Also identify all zero...

A: We have to find the forces in the members CD, CJ, IJ of the truss

Q: complete solution!! Calculate the minimum wall thickness for a cylindrical vessel that is to carry...

A: Given data, A cylindrical vessel,having Diameter= 2ft = 2×12 in = 24in. Pressure= P= 1500lb/in² All...

Q: P B C L-

Q: Determine the stress increase at

Q: The figure shown a motor pulling an object in an in clined surface determine the power required to m...

A: Given, Velocity = 3.5 m/s μ = 0.20

Q: equation contains the following term(s): pressure term (expansion/compression work) O velocity term ...

A: Considering it to be the question at fluid mechanics Conservation of Energy i.e Bernoulli equation c...

Q: Solve Castigliano's theorem. Show written solution on this problem.

Q: A fillet-welded joint of 6 mm size is shown in the figure. The welded surfaces meet at 60-90 degree ...

Q: A beam with varying load is shown at the figure below. If the beam properties are given, what is the...

Q: The 350-N lamp is supported by three steel rods connected by a ring at A. The average normal stress ...

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of understandin...

Q: A 15-kg solid cylinder rolls without slipping down the incline (30° with the horizontal). Determine ...

Q: A person buys a piece of lot for $100,000 down payment and 10 deferred semi-annual payments of $8,00...

A: The cash price of the lot :

Q: A particle moves along a straight line with a velocity V = 12-312 m/s, where t is in seconds. When t...

Q: For the beam shown below, derive the expressions for V and M and draw the shear force and bending mo...

Q: 1.8 m 1.8 m 2 m

A: Uniform bar A cross section is when you cut an object in half and expose the shape inside. Uniform i...

Concept explainers

Fluid Materials

In general terms, anything that flows can be termed as a fluid. In other words, a fluid is any substance that cannot resist shear forces and deforms continuously under the application of external shear forces. Fluid materials differ completely from solid materials such as metals and alloys. For instance, if we consider two infinitesimally small cross-sectional areas of fluid materials and solid materials, and apply shear forces to these elements, both the elements will undergo deformation. Upon releasing the shear force, the element of the solid materials will regain its original orientation, but the element of the fluid materials will keep on deforming continuously under the action of the shear force.

Question

4. In the following, which one is the water-based fluid?(single choice)
A.Polymer drilling fluids
B.Synthetic-based drilling fluids
C.Oil-based drilling fluids
D.Form/Mist drilling fluids
5. In the following, which one is not the properties of drilling fluids?(single choice)
A.Density
B.Viscosity
C.Mass
D.Filtration
6. Regarding the fluid models, which one is incorrect?(single choice)
A.plastic viscosity µo = lim -
Y-00 Y
B.apparent viscosity Ha =
C.Power law fluid model 7 = ky
D.Bingham plastic model t = To + HooY

1. Regarding the circulating system, which one is correct?(single choice)
A.Drilling fluid flow path: mud pit-mud pump-standpipe+swivel-kelly-drill pipe
-drill collar drill bit-annulus+solid control system-mud pit
B.Drilling fluid flow path: mud pit+mud pump-standpipe-swivel-kelly-drill bit-
drill pipe-drill collar*annulus*solid control system-mud pit
C.Drilling fluid flow path: mud pit-mud pump-swivel-kelly-drill pipe-standpipe
-drill collar-drill bit-annulus+solid control system-mud pit
2. In the following, which one is not the correct function of drilling fluids? (single
choice)
A.Control wellbore pressure
B.Cuttings transport
C.Pollute the environment
D.Transmit hydraulic horsepower
3. For the function of control subsurface pressure, what are the major influencing
factors? (multiple choice)
A.Mud weight
B.Flow rate
C.Rheological properties
D.Filtration properties

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step by step

Solved in 6 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Task 2 Calculate forces related to fluids at rest and in motionb) An alternative suggestion for the drainage is to replace the pipe with an open channel ofwidth 2m which would have the same slope as the pipe and made of smooth concrete witha Manning friction value of 0.12 c) Compare the open channel with the pipe system for providing the required drainage
1-D flow.
Please find normal discharge for a 400mm diamter drainage pipe. manning's n = 0.013 the pipe is partially filled angle = 120 degrees, if the slope drops 1m over 1000m Pleasen show hand calculations and explain steps, thankyou!
Water at 15°C is pumped from a reservior at a rate of 0.1131 m3/s where the local atmospheric pressure is 94.6 kPa. The total head loss in the suction pipe is 1 m. From the manufacturer data, the NPSHrequired at this operating point is 7.8. Determine the maximum height hs (meters) before cavitation can occur. Round off your answer to 3 decimal places.
Water is flowing at the rate of 300 lit/sec from A to E as shown. Compute the fiow in each pipe in lit/sec and the total head loss. Assume f = 0.025 for all pipes.
Hydraulic subject -Civil. Please answer only if you are 100% sure ,Do not provide Ai solution without verifying.
a plastic tile drain pipe is installed to carry a design flow from 3000ft of tile spaced 140 ft . if the soil drainable porosity is 0.06 and the drainage coefficinet to drop the water table is 0.21 m/day . and the grade of the tile is 0.2percent . the roughness cofficient (n) is 0.017 . the design diameter of the drain pipe (d) is egual meter ?
Is it possible to have an irrigation sprinkler system without mainline? the laterals were directly connected to the pump.
A 1 m diameter new cast iron pipe 800 m long and had a head loss of 1.11 m Find the discharge in Lit:sec if C=130 Please help. Show complete solution and avoid truncation. Thank you
Calculate the required pipe diameter to avoid cavitation, if the pump deliversQ = 30US gallon/min water from a closed tank, where the pressure (above thewater level) is p = 40kPa. The equivalent length of the smoothened concretepipe on the suction side is 12m while the suction flange of the pump is 8m belowthe water level. The vapour pressure at the given water temperature is 2.8kPa.The required net positive suction head is NPSHr = 3.2m. Show the complete solution and units being cancelled.
Calculate the required pipe diameter to avoid cavitation, if the pump deliversQ = 30US gallon/min water from a closed tank, where the pressure (above thewater level) is p = 40kPa. The equivalent length of the smoothened concretepipe on the suction side is 12m while the suction flange of the pump is 8m belowthe water level. The vapour pressure at the given water temperature is 2.8kPa.The required net positive suction head is NPSHr = 3.2m. Please show complete formulas and units being cancelled.
Find the discharge over a triangular notch of angle 60 degrees, when head over the triangular notch is 0.25m. Assume C=0.57. Show complete details of your solution. Provide illustrations. Use three decimal places.