4. It is desired to configure a PWM Output Pin on an ATmega328P. Write the AVR Assembly code that will set up an output pin for one of the 8-bit timers (Timer0 or Timer2) to meet the following specification: Phase Correct PWM, TOP = $FF, Output is NON-INVERTED, PWM frequency is 980 Hz and the duty cycle is 33%.

4. It is desired to configure a PWM Output Pin on an ATmega328P. Write the AVR Assembly code that will set up an output pin for one of the 8-bit timers (Timer0 or Timer2) to meet the following specification: Phase Correct PWM, TOP = $FF, Output is NON-INVERTED, PWM frequency is 980 Hz and the duty cycle is 33%.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

What are the content of R16 and the carry flag after the execution of the following sequence of instructions? SEC LDI R16, 0x29 ROR R16 LSR R16 Select one: a. R16=0x4A and c=1 b. R16=0xCA and c=0 c. R16=0x4A and c=0 d. R16=0xCA and c=1
In the following instruction sequence, show the values of the Carry, Zero, and Sign flagswhere indicated:mov al,00001111btest al,00000010b ; a. CF= ZF= SF=mov al,00000110bcmp al,00000101b ; b. CF= ZF= SF=mov al,00000101bcmp al,00000111b ; c. CF= ZF= SF=
In the following code sequence, show the value of AL after each shift or rotate instructionhas executed:mov al,0D4hshr al,1 ; a.mov al,0D4hsar al,1 ; b.mov al,0D4hsar al,4 ; c.mov al,0D4hrol al,1 ; d
Build C program to perform task below. Design its circuit in Proteus. State your observations.a) Make Port D produce 5V. Use bit addressable instructions.b) Make pin RB7, RB5, RB3 and RB1 ON and other Port B pins OFF. Use byte addressableinstruction.c) Make RE0, RA1, RB2, RC3 and RD4 HIGH.result discussion conclusion
destination register after each of the following instructions executes in sequence, given that CL, DX, and AL are initialized to 3, 1001111010111100, and 01010111 respectively? Leave your answer in binary form for this question rol dx, cl
Select an OR instruction that will:a) OR BL with AH and save the result in AH.b) OR 88H with CX.c) OR DX with SI and save the result in SI.d) OR 1122H with BP.e) OR the data addressed by BX with CX and save the result in memory.f) OR the data stored 40 bytes after the location addressed by BP with AL and save the result in AL.
Identify the addressing modes used for the source and the destination operands in the instructions thatfollow :(a) MOV AL, BL(b) MOV AX, 0FFH(c) MOV [DI], AX(d) MOV DI, [SI](e) MOV [BX]+0400H, CX(f) MOV [DI]+0400H, AH(g) MOV [BX][DI]+0400H, AL
What is the value of DX after the instruction (subtraction)? DX = 35F3H BX = 7235HSUB DL, BHSelect the correct response:A.129 B. 3581C. 3581HD. 128
The content of AC in the basic computer is hexadecimal 85B2 and the initial value of E is 0. Determine the contents of AC, E, PC, AR, and IR in hexadecimal after the executing of the CMA instruction.
For the following instructions show which are allowed and not allowed then write the reasons: -SUB SS, DS -ADD [BX],[300H] -SUB 08, AL -INC [BX+5] -ADC CX, DL
Select an instruction that tests bit position 8 of register CH. MULTIPLE CHOICES A. a or bB. None of the choicesC. BT CH, 8D. TEST CH, 128
Specify the register contents and flag status as the following instructions are executed. A B S Z CY MVI A, FFH RRC MOV B,A ADD B RAR DCR A HLT