answer quickly 4. Outdoor air at 90°F dry bulb and 75°F wet bulb temperature iscooled and dehumidified to dry bulb temperature 60°F andrelative humidity 40%. The process occurs at 101.3kPabarometric pressure. Assume specific heat capacity of air as0.24 Btu/lb °F(a) Draw a sketch illustrating this process and show this in ap-chart.(b) Derive steady state energy and mass conservationequations.Determine:d) the mass of water condensed per kilogram of dry air,(c) the sensible heat and latent heat per kilogram of dry air(e) the sensible heat factor (SHF)

Answered: Image /qna-images/answer/25fc67fa-df5e-4523-b219-0541202bfe36.jpg

Answered: 4. Outdoor air at 90°F dry bulb and…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

please show whole solution thank u 1.What is the state of a water vapor at 50°Fdew point temperature and 80 °F dry-bulb temperature? (use the psychometric chart to determine the state of the steam
Calculate the water vapor pressure of the atmosphere if the dry-bulbtemperature is 22°C and the wet bulb temperature is 10°C at standardatmospheric pressure , Calculate also the relative humidity, the degree or percentof saturation , humidity ratio , and the enthalpy of the mixture. solve with complete diagram
Moist air initially at standard atmospheric pressure, 15°C db, 70% relative humidity undergoes a sensible heating process until the dry bulb temperature is 29°C. For a moist air mass flow rate of 9.9 kg/s, what is the heat transfer for this process? Express your answer in kW.
Solve all please i give thumb up? Outside air at 15°C and 20% relative humidity is admitted at a volumetric rate of 15m³/min into an air conditioning system composed of a simple heating section followed by a humidification section, which must supply air at 27 °C and 65% relative humidity. The airflow temperature between the heating and humidifying sections is 22°C and the entire air conditioner operates at 70kPa. Determine, using calculations: (a) the rate of heat supply to the heating section, in kW, is ______. (b) the wet bulb temperature of the air after the heating section, in °C, is ______. (c) the mass flow rate of steam in the humidification section, in g/s, is ______. (d) the temperature of the steam injected into the humidification section for a steam pressure of 200kPa, in °C, is _______
The air conditions at the intake of an air compressor are 29 C, 50 percent relative humidity, and 101 kPa. The air is compressed to 400 kPa, then sent to an intercooler. If condensation of water vapor from the compressed air is to be prevented, what is the minimum temperature (tdp) to which the air can be cooled in the intercooler?Use theoretical calculation for this problem.
Pls solve accurate and fast A 1-kg steam-water mixture at 1.0 MPa is contained in an inflexible tank. Heat is added until the pressure rises to 3.5 MPa and the temperature to 400: Determine the heat added
Q3. Moist air at 50°C and 60% relative humidity is heated to 80°C. What are the initial and final humidity, enthalpy, specific volume and dew point of the air?
Consider saturated liquid water at 100°C, contained in a piston-cylinder device.It is then subjected to pressure to reduce the volume by 2% isothermally. Thepressure is:
Classify whether the properties given is for subcooled liquid (SC), saturated liquid (SL), wet mixture (WM), saturated vapor (SV), superheated vapor (SP) or saturated (S) (can be liquid or vapor)
800 CFM of air at 90 °F, 50% rh is cooled to saturation. Determine the rate of heat transfer for the cooling process.
Moist air at 35 °C dry-bulb temperature and 50% relative humidity enters a cooling coil at 300 m³/min and is processed to final saturation condition at 12 °C. Draw the process on the psychometric chart and find the required cooling load in kW. Assume the enthalpy of the removed water is hw = 42kJ / kg
Consider a sealed can that is filled with 4.4 kg of water at 115 °C and P = 248 kPa. Now a leak develops, and the pressure in the can drops to the local atmospheric pressure of 100 kPa (Cp=4.23 kJ/kg.K). The vapor leaves the can as soon as it is formed. How much vapour will evapourate before the liquid water reaches its boiling temperature at atmospheric pressure. NB: water's enthalpy of vapourisation is roughly 2257 kJ/kg . a. 4.400 kg b. 0.120 kg c. 1.093 kg d. 0.030 kg e. 0.015 kg

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS