4. The water tank is below a constant level at depth h rectangular hole a x b. We close the opening with an immersion wall from the upper edge of the hole by a distance X. Given: h = 0.85 m, a = 0.4 m, b = 0.7 m. Determine: by what distance x do we have to move the immersion wall, to reduce the flow 3 times, what will be the flow Q1 at submerged wall by x, Reynolds number Re in flow, nature of flow.

4. The water tank is below a constant level at depth h rectangular hole a x b. We close the opening with an immersion wall from the upper edge of the hole by a distance X. Given: h = 0.85 m, a = 0.4 m, b = 0.7 m. Determine: by what distance x do we have to move the immersion wall, to reduce the flow 3 times, what will be the flow Q1 at submerged wall by x, Reynolds number Re in flow, nature of flow.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water flows out of a faucet at A at 6 m/s. Determine thevelocity of the water just before it strikes the ground at B
A uniform tube is used to siphon water from the large tank. If the pressure on the outside of the tube (the atmospheric pressure) is more than 20 kPa greater than the pressure within the tube, the tube will collapse. By using Bernoulli's equation, determine the minimum value of h allowed without the siphon collapsing. The density of water is 1000 kg/m3. Hint: Since the tube is uniform the flow speed in it is constant. The exiting flow from the tube is treated as free jet. 2 m V SARA 1 4 m
a)Determine the value of h in the siphon shown if velocity at C was 11.7 m/s. Diameter of the pipe is 2.5cm. b) Determine the pressure at point B.
Neglecting head losses, determinewhat horsepower the pump must deliver toproduce the flow as shown. Here theelevations at points A, B, C, and D are 110 ft.200 ft, 110 ft and 90 ft, respectively. The nozzle area is 0.10 ft2
A horizontal pipe is full of flowing water. At location A the velocity is 1.5 m/s and the pressure is 138 kN/m2. If the pipe tapers gradually from 150mm diameter at A to 100mm diameter at location B, determine the pressure of the water at B, assuming there is no loss of energy.
Water, issuing vertically from a nozzle having a diameter of 25 mm, flows out under a head of 30 m. If C = Cv = 0.98, determine at what constant height could the jet of water support a load of 200 N vertically from the nozzle tip?
The pipe bend shown is in a horizontal plane. Oil with a specific gravity of 0.86 enters the reducing bend at section A with a velocity of 3.2 m/s and a pressure of 150 kPa. Determine(a) Thevelocity(m/s)atsectionB.(b) Thepressure(kPa)atpointB.(c) FP (x-direction),(d) FP (y-direction),(e) The magnitude and direction of FRX of the force required to hold the bend in place.(f) The magnitude and direction of FRY of the force required to hold the bend in place.Forces are to be expressed in Newtons.
The diameter of a pipe gradually reduces from 1 m to 0.7 m. The pressure intensity atthe center line of 1 m section is 8and rate of flow of water through the pipe is600 liters/s.,I. Find the intensity of pressure at the center line of 0.7 m section.II. Determine the force exerted by flowing water on transition of the pipe.
An elbow deflects water upward and discharges it to the atmosphere at a specific rate. Determine the gage pressure at the inlet of the elbow and the anchoring force needed to hold the elbow in place. (gage pressure at the outlet is zero)
Water at 20°C, in the pressurized tank flows out and creates a vertical jet as shown. Assuming steady frectionless flow, determine the heaght H to which the jet rises.
Water flows at a rate of 3 m3/s through a 300 mm diameter pipe in which there is a 90o bend. if the pressure at the entrance to the bend is 450 kN/m2 (absolute), determine the total force necessary to anchor (kN) the bend. Friction losses can be neglected.
The figure shows a siphon that is used to draw waterfrom a large open tank. If the absolute vapor-pressureof the water is pv = 1.23 kPa. (a) determine the shortest drop length L of the50-mm-diameter tube that will cause cavitation in thetube. Show all your calculations. (b) Also draw the energy and hydraulic grade lines forthe length of the tube. Be sure to indicate the pressureheads, elevation heads, and dynamic heads. And toshow all your calculations.