4.1 The aluminum rod AB (Gal = 27 GPa) is bonded to the brass rod BD (Gbr = 39 GPa). The portion CD of the brass rod is hollow and has an inner diameter of 40 mm. If the allowable shear stresses for the aluminum and brass are 90 MPa and 70 MPa, respectively, and the allowable angle of twist of the free end A is 6 degrees, determine the maximum permissible value of T.

Q: 650 ms, 450 ms and 300 ms,

A:

Q: The lowest flow in the Ozama River in July is about 48 m3/s. The dissolved oxygen concentration of…

A:

Q: SITUATIONI A rectangular reinforced concrete beam, 5 m long is carrying a dead load of 18 kN/m and a…

A: Solution: Given: Span = 5 m DL = 18 kN/m LL = 35 kN/m fc = 21 MPa, fy = 415 MPa b = 300 mm d = 400…

Q: Ar 18. Viscosity of a fluid with specific gravity 1.3 is measured to be 0.0034 Ns/m2. Its kinematic…

A:

Q: 5. A compound curve is joined by two simple curves adjacent to each other, the first one having a…

A: given - compound curve is formed by joining 2 simple curve  first curve - radius = 200m, central…

Q: I need a report on Error Analysis

A: Error Analysis is a method used to document the errors that appear. Errors are broadly classified as…

Q: Q.81 The point of contraflexure in the beam from C will be 10 kN 10 kN/m 10 m 2 m C

A:

Q: determine the support reaction in beam at point

A:

Q: What are the considerations made between building a swallow and a deep foundation? Expound your…

A: The engineer should be aware that the size and type of base mass are determined by economic factors.…

Q: What will be the error in the measurement of dischrage if the error in the measurement of head in a…

A: Given, A 'V' notch, having error in head, dH/H =1%

Q: + SCALE: 1 = 2

A: Only handmade drawings are attached for understanding. Dimensions are not included.

Q: A steel column W300 x 203 kg/m section is used as to support an aial load. A=25740mm^2        Tw =…

A:

Q: -A 8teel pod is stretcke between two rugid walls ard carries a tensile Coad f GO0ON a C If the…

A:

Q: 2. From the figure shown, rigid bars are separated by a roller at C and pinned at A & D. A steel rod…

A: To find out the vertical displacement of the roller at C.

Q: On a tourist map with a scale of 1:50 000, the distance between Arabasta and Wano is 13 cm. What is…

A: We knowScale=Map DistanceOriginal distance

Q: . stresses in the steel b. nominal load, Pn

A:

Q: I. Problem Solving: Answer what is being required. Show you complete solution. 1. Compute the…

A:

Q: A sample of wastewater is mixed with 2 parts clean water and placed in a bottle. The DO of a sample…

A: Given data : The value of initial dissolved oxygen D.Oi=10 mg/L The value of Final dissolved oxygen…

Q: Explain how sampling and testing of masonry are done according to the ASTM standards.

A: Sampling standards and testing of concrete units are developed by ASTM International technical…

Q: An inclined plate 2 m long and 1 m wide lies with its length inclined at 45° to the surface of water…

A:

Q: A sampler with a volume of 45 cm' if filled with a soil sample . When the soil is poured into a…

A:

Q: The use of rational formula assumes that rainfall occurs uniformly over the entire watershed. True…

A: True  The following are the assumption of rational formula:  1. The drainage area is small. 2.The…

Q: State the five (5) major steps used in engineering design and problem solving process.

A: The five major steps in engineering design and problem solving process are as: Defining the…

Q: A 3 m high vertical earth retaining wall retains a dry granular backfill with angle of internal…

A:

Q: How can we find the maximum shear on a beam if the beam is to be subjected to moving loads.? How can…

A: We find out the maximum shear(or shear force) on the beam if the beam is simply supported and the…

Q: A reinforced concrete beam has a width of 250 mm and a total depth of 450mm. It carries an ultimate…

A:

Q: _7. The strain in an axial member of a square cross-section is given by. e- h ?E where h= length or…

A: We will use error in division and power formula.

Q: Tapped into a 3-cm diameter horizontal water pipe is a piezometer and a Pitot tube. The height of…

A: Given: Level of water in pitot tube,h1= 20 cm = 0.2 m Level of water in piezometer,h2= 35 cm = 0.35…

Q: Pipes 1, 2, 3 and 4 have lengths 100oft, 800 ft, 700 ft and 1500 ft, all being new cast iron (f…

A:

Q: Example 3: Draw the shear and moment diagrams for the beam shown below. W A

A:

Q: Calculate the quantity of Cement, Sand, Gravel and Water for the given solid as shown and the…

A:

Q: An auto A is moving at 6m/s and accelerating at 1.5m/s^2 to overtake an auto B which is 115.2m…

A:

Q: Show the complete solution. Solve for the x and y components of each force acting on the plate of…

A:

Q: 18. Viscosity of a fluid with specific gravity 1.3 is measured to be 0.0034 Ns/m2. Its kinematic…

A: Given data: Viscosity, δ=0.0034 Nsm2 Specific gravity, μ=1.3

Q: Determine the design strength, kN-m.

A:

Q: EX: The pipe has a diameter of (1.2m) at A. (1.5m) at B and (0.8m) at C. The discharge at C is…

A:

Q: The figure shows a pin-jointed plane truss loaded at the point M by hanging a mass of 100 kg. The…

A:

Q: Q. Find the Lacey's scour depth for a stream carrying discharge of 4 cumec/m and having silt factor…

A: Given:  Discharge per unit width of stream, q=4 cumec/m Silt factor, f=1.2   To find: Lacey's Scour…

Q: A tank is connected with cart by the rope A as shown in figure. When the water leaves the tank from…

A:

Q: THIS IS NOT GRADED.  This is a 2020 Past Paper that I am working through. However I only have the…

A:

Q: Consider the spring mass system shown below. The natural frequency of the system is 4rad/s for a…

A:

Q: The following land and the land use of the area with the corresponding runoff coefficients are given…

A: Runoff : Runoff happens when there is more water than the soil can absorb. The excess liquid rushes…

Q: What will be the shift of the transition curve, if the length of the transition curve is 80 m and a…

A: given- Radius of curve R=300 mLength L=80 m

Q: Find the maximum shear and moment values by using the Shear The section of the rectangular beam has…

A:

Q: Problem # 4: Three links are used to support load P = 10.25 kips. Disregarding any defomation for…

A: ASKED: To determine- axial stress in link AB axial strain sustained by link CD.   Given, Load P =…

Q: A reinforced concrete beam having a width of 350mm and a overall depth of 600 mm is reinforced with…

A:

Q: Calculate the slope at C using ONE of these methods: double integration method, area- determine the…

A:

Q: The test results of a soil sample are give below. Percentage finer than 4.75 mm = 55 Percentage…

A:

Q: A 45° sector gate is located on the crest of spillway. The water is upto the mid- point of the gate…

A:

Q: From the figure shown, rigid bars are separated by a roller at C and pinned at A & D. A steel rod at…

A:

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.