Question 3 o(MPa) The elastic portion of the stress-strain diagram for a steel alloy is shown in the figure. The specimen from which it was obtained had an original diameter of 3xb mm and a gauge length of 12xb mm. When the applied load on the specimen is 10xa kN, the diameter is [(3xb)-0.00735] mm. Determine Poisson's ratio for the material. 400 «(mm /mm) 002

Question 3 o(MPa) The elastic portion of the stress-strain diagram for a steel alloy is shown in the figure. The specimen from which it was obtained had an original diameter of 3xb mm and a gauge length of 12xb mm. When the applied load on the specimen is 10xa kN, the diameter is [(3xb)-0.00735] mm. Determine Poisson's ratio for the material. 400 «(mm /mm) 002

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.14P

See similar textbooks

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the length over which the elongation is measured) of 4 inches. The dam were plotted on a load-displacement graph. P vs. L. A best-fit line was drawn through the points, and the slope of the straight-line portion was calculated to be P/L =1392 kips/in. What is the modulus of elasticity?
The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
A tensile test was performed on a metal specimen having a circular cross section with a diameter of 1 2 inch. The gage length (the length over which the elongation is measured) is 2 inches. For a load 13.5 kips, the elongation was 4.6610 3 inches. If the load is assumed to be within the linear elastic rang: of the material, determine the modulus of elasticity.
A 2-m long steel rod, 10-mm in diameter, is carrying a load of 20 kN. (a) what is the axial stress developed in the rod, in kN/m^2. Is the tensile or compressive? (b) compute the amount of elongation (in mm) in the steel rod caused by the applied load, (c) what will be the elongation (in mm) in the steel rod if the weight of the steel rod is included? Use density of the steel to be 7860 kg/m^3. Young's modulus of elasticity, E=200GPa. W=mg. Draw free body diagram of the steel rod.
The polymer bar shown in the figure below has a width of b=55b=55 mmmm, a depth of d=104d=104 mmmm, and a height of h=274h=274 mmmm. At a compressive load of P=120P=120 kNkN, the bar height contracts by Δh=−2.60Δ⁢h=-2.60 mmmm, and the bar depth elongates by Δd=0.36Δ⁢d=0.36 mmmm. At this load, the stress in the polymer bar is less than its proportional limit. Determine: (a) the modulus of elasticity. (b) Poisson’s ratio. (c) the change in the bar width bb.
A cylindrical specimen of 1018 steel having a diameter of 6.35 mm and a gauge length of38.1 mm is pulled in tension. Use the load-elongation characteristics tabulated below. Determine the yield strength (σy) at a strain offset of 0.002.
1.2 A hollow steel rod has a length of 1m. The outside diameter of the rod is 0.2m and the inner diameter is 0.18m. The rod is compressed axially with a load of 200kN. The modulus of elasticity and the Poisson's ratio of the rod are 200GPa and 0.3 respectively. Determine the increase in outside diameter of rod using the calculated value of decrease in length. (The decrease in length=0.17mm)
A steel wire with a diameter of d = 1/16” is bent around a cylindrical drum with a radius ofR = 36”.(a) Determine the maximum normal strain in the wire.(b) What is the minimum acceptable radius of the drum if the maximum normal strain mustremain below yield? Consider an elastic modulus of 30000 ksi and yield stress of 100ksi.(c) If R = 36”, what is the maximum acceptable diameter of the wire if the maximum normalstrain must remain below yield?
A hollow aluminum tube used is a roof structure has an outside diameter d2 and inside diameter d1. The tube is 2.5m long and the aluminum has a shear modulus of G=28 GPa. a.If the tube is twisted in pure torsion by torques acting at the ends,what is the angle of twist in degrees when the max shear stress is 50MPa? b.What diameter “d” is required for a solid shaft to resist the same torque with the same maximum stress? d1 = 90 (mm) d2 = 110 (mm)
At the proportional limit, the axial load of a 0.70-in-diameter bar was 5400 lb. A 2.20-in. gauge length on the bar has increased by 0.0040 inch. a) Determine the strain in the bar.b) Determine the elastic modulus (in ksi)