4.As shown in the figure, a U-tube pressure gauge containing mercury is installed on the water storage tank. The difference between the water surface height of the water tank and the average height of the mercury surface in the manometer is z. the height difference between the two sides of the mercury surface is 2h. What is the ratio of z to h (z/h)? (The density ratio of mercury to water is s=13.6) Pa Pa Pw water A mercury "ds="d

4.As shown in the figure, a U-tube pressure gauge containing mercury is installed on the water storage tank. The difference between the water surface height of the water tank and the average height of the mercury surface in the manometer is z. the height difference between the two sides of the mercury surface is 2h. What is the ratio of z to h (z/h)? (The density ratio of mercury to water is s=13.6) Pa Pa Pw water A mercury "ds="d

Name: 4.As shown in the figure, a U-tube pressure gauge containing mercury
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 4.As shown in the figure, a U-tube pressure gauge containing mercury is installed on the water storagetank. The difference between the water surface height of the water tank and the average height of themercury surface in the manometer is z. the hei

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter1: Heat, Temperature, And Pressure

Section: Chapter Questions

Problem 14RQ: Atmospheric pressure at sea level under standard conditions is ______inches of mercury (Hg) or_____...

See similar textbooks

Similar questions

A 150 inclined manometer containing mercury is connected to two taps A an B containing water. Tap B is 4 ft vertically higher than Tap A. When the pressure in Tap B is 6 psi, the manometer reads 5 inches along the inclined tube. Calculate the new manometer reading (in inches) if the pressure in Tap A is increased by 2 psi.
For the figure shown, determine the pressure at point D, if the specific gravity of oil is 0.9 and the manometer fluid is 0.7
The value of the pressure gauge A in the B tank is 1.4 bar. The U-type manometer connected to tank B contains mercury. Determine the absolute pressures in tank A and tank B. (each with a bar)
Find the gauge pressure at point A for the system of manometers shown in the Figure 1.
In the figure, pressure gauge A shows 1.5 kPa (gauge). Fluids are at 20 ° C. Determine the elevation z in meters of the level at which to find the liquids in tubes B and C.
The system shown in the figure is used to accurately measure the pressure changes when the pressure is increased by ΔP in the water pipe. When Dh = 70 mm, what is the change in the pipe pressure?
In the figure, fluids A and B have specific gravities of 0.75 and 1.00, respectively. If mercury is used as the manometer liquid, determine the pressure difference between A and B in psi.
The pressure difference between point A and point B is to be measured using an inclined mercury (SG 13.6) manometer. The manometer is inclined at 15 degrees. If the reading along the manometer is 4.8 cm, find the pressure drop between A and B. Include a diagram in your solution. Assume the other liquid in the manometer is air, and operating temperature is 25 degrees Celsius.
The gauge pressure of the air in the tank shown in below figure is 85 kPa. Determine thedifferential head h of the mercury column. [Note: Balance the pressures on both limbs of themanometer, s stands for specific gravity]
An oil of specific gravity 0.88 is flowing through the pipe of diameter 30cm. one end of the simple U tube manometer contains mercury, is inserted with the center of pipe and other end is open to atmosphere. The level difference in mercury is found in the right limb as 32 cm. The distance between the center of the pipe and the mercury level in right limb is 18 cm. Find the pressure of oil in the pipe in kPa. Draw the diagram neatly. (Enter only the values by referring the unit given. Also upload the hand written answers in the link provided) The pressure of oil in the pipe (in kPa)
In the system shown in the figure, find the relative pressures at points 1, 2, 3 and 4 and the absolute pressure measured on the M gauge.
An open manometer, shown in the figure, is installed to measure the pressure in a pipe carrying an oil (SG = 0.82). If the manometer liquid is carbon tetrachloride (SG = 1.60) determine the pressure in the pipe (in N/m2). Find the pressure head in meters of water column height.