I need the answer Find the capillary raise of the water in thetube of diameter 2mm, which is immersedvertically in the container. The surfacetension of water is 0.07115 N/m. Take theangle of contact is 0 = 0°(ENTER ONLY THE VALUES IN THE BOXESBY REFERRING THE UNIT GIVEN INBRACKETS)The capillary raise of water in the tube is(unit in mm)=

Answered: Image /qna-images/answer/6544c05b-f6f7-4aa3-bf55-869d3f999f89.jpg

Find the capillary raise of the water in the tube of diameter 2mm, which is immersed vertically in the container. The surface tension of water is 0.07115 N/m. Take the 0° angle of contact is 0 = (ENTER ONLY THE VALUES IN THE BOXES BY REFERRING THE UNIT GIVEN IN BRACKETS) The capillary raise of water in the tube is (unit in mm)=

Find the capillary raise of the water in the tube of diameter 2mm, which is immersed vertically in the container. The surface tension of water is 0.07115 N/m. Take the 0° angle of contact is 0 = (ENTER ONLY THE VALUES IN THE BOXES BY REFERRING THE UNIT GIVEN IN BRACKETS) The capillary raise of water in the tube is (unit in mm)=

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.122P: The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate...

See similar textbooks

Similar questions

The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate and the smooth surface at B due to water pressure acting on the gate. Use =62.4lb/ft3 for water.
One side of the container has a 03-m square door that is hinged at its top edge. If the container is filled with water, determine the smallest force F that must be applied to the bottom edge of the door to keep it closed.
Compute the surface area of the axi-symmetric domed structure.
The hemispherical glass bowl is filled with water. Find the location y of the center of gravity of the filled bowl. Approximate the bowl as a thin shell of radius R=6.15in. Use 1=162lb/ft3 for glass and 2=62.4lb/ft3 for water.
Find the capillary raise of the water in the tube of diameter 6mm, which is immersed vertically in the container. The surface tension of water is 0.07115 N/m. Take the angle of contact is = 00 The capillary raise of water in the tube is (unit in mm)= ______
Two capillary tubes with 4mm and 2mm inside diameters were inserted into a liquid of density 1.12gcm^-3. Calculate the surface tension of the liquid if the difference between the capillary rises in the tubes is 2cm. Assume contact angle Is zero.
What force, F, must be applied to the S-shaped gate to keep it closed? The gate is 1 m wide andthe radius of curvature of each part is 1 m. The liquid is water.
Compute the capillary rise of water between two concentric glass tubes of radius r 1 = 2mm, r 2 = 4 mm with a contactangle ϴ = 20ᵒ. Surface tension = 0.07321 N/ m.
To what height will 68˚F ethyl alcohol rise in a 0.005 in internal diameter glass capillary tube? The density of the alcohol is 49 lbm/ft3 note ? = 0.00156 ???/ ?? and ? = 0°.
Derive a formula for capillary rise (h) between two concentric glass tubes of radiuses RI and R2. determine its value for water if (G. = 0.072 N/m, RI=30mm, & R2=36mm) (Take smooth and very clean glass tubes).
Water is the fluid in the pipe as shown, and mercury is the manometer fluid. If the deflection Δh is 60 cm and L is 180 cm, what is the gage pressure at the center of the pipe in kPa? delta h is between point 1 and 2.
The pipe (0-1-2) shown in the …gure is angled upward at 30 and is …lled with water. The distance from (1) to (2) (along the pipe) is 1.2 m. The manometer liquid is mercury. For part (a), the pipe is capped at location (0) so that the water is stationary in the pipe. What would be the value of h in this case? For part (b), the pipe shown is just a section of a much longer pipe, and water is ‡owing upwards from (0) to (1) to (2). If the pressure loss due to friction from location (1) to location(2) is 20 kPa, what is the value of h in this case?