40 - Which of the following are not to be considered in machine tool selection?(Aşağıdakilerden hangisi tez O A) Cutting and feedrate settings should be made over a wide range( ma ve ilerleme hiz The machine must be maintenance-free O B) --altiron türdon olm O C) The type of control and the number of service personnel should correspond to the number of parts to be manufactured( u turu ve hizn en- sayısı, ima O D) Themachine tool should be able to be equipped with additional equipment and measuring instruments(T VIĻU aieuen ne uUnatilabilmelidir) O E) The power of the machine should be suitable for working by removing the thickest chips( nnhin niinis an valin talaei kaldırarak caliemava inn at

40 - Which of the following are not to be considered in machine tool selection?(Aşağıdakilerden hangisi tez O A) Cutting and feedrate settings should be made over a wide range( ma ve ilerleme hiz The machine must be maintenance-free O B) --altiron türdon olm O C) The type of control and the number of service personnel should correspond to the number of parts to be manufactured( u turu ve hizn en- sayısı, ima O D) Themachine tool should be able to be equipped with additional equipment and measuring instruments(T VIĻU aieuen ne uUnatilabilmelidir) O E) The power of the machine should be suitable for working by removing the thickest chips( nnhin niinis an valin talaei kaldırarak caliemava inn at

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter1: Introduction To Machining

Section1.1: Introduction To Machining

Problem 9RQ: What machine tool is available with either horizontal or vertical spindle orientation and uses...

See similar textbooks

Similar questions

1. Name principal parts of knee and column type milling machine and explain their functions. 2. Define milling machine.
What is the difference between machine and machine tool?
Name three major collet styles used in toolholding. a. ________________________ b. ________________________ c. ________________________
What is a benefit of using a DRO instead of micrometer collars for positioning on a vertical milling machine?
What machine tool is available with either horizontal or vertical spindle orientation and uses rotating cutting tools to primarily produce flat surfaces?
List three characteristics of a workpiece that would make a mandrel the ideal workholding device.
A selection between advanced machining operation and conventional machine operation is to be made for mass production of 1000 parts. The part is a 20mm thick stainless steel plate and a hole of 10mm must be drilled. Calculate time required, material removal rate and feed rate for both processes to make a known decision to save production cost. The ECM process require 1000amp current with an expected efficiency of 90% whereas the conventional drilling is to be done with 8mm drill through hole. The point angle is 118°. The cutting speed is 15m/min and the feed is 0.30 mm/rev. The part handling time for ECM is 1min whereas for conventional process is 1.5min with the use of jig.
As the manager of a large machining workshop you are required to prepare the specifications of a lathe machine to be purchased to replace an old one which has been used for the last 25 years. Outline the main specifications that you deem important to suit the requirements of the workshop.
1. Enumerate at least 3 items that we should check prior to machining. 2. Enumerate the 5 minimum personal protective equipment (PPE) required during machining. 3. In case of emergency, where can we locate the emergency stop of milling machine? 4. In milling machine, how many axis can we operate the worktable?
Machine setup steps should be stated in bullet points for ease.
21.40 Explain whether it is desirable to have a high or low (a) n value and (b) C value in the Taylor tool-life equation.
A NC lathe cuts two passes across a cylindrical workpiece under automatic cycle. The operator loads and unloads the machine. The starting diameter of the work is 3.00 in and its length = 10 in. The work cycle consists of the following steps (with element times given in parentheses where applicable): 1 - Operator loads part into machine, starts cycle (1.00 min); 2 - NC lathe positions tool for first pass (0.10 min); 3 - NC lathe turns first pass (time depends on cutting speed); 4 - NC lathe repositions tool for second pass (0.4 min); 5 - NC lathe turns second pass (time depends on cutting speed); and 6 - Operator unloads part and places in tote pan (1.00 min). In addition, the cutting tool must be periodically changed. This tool change time takes 1.00 min. The feed rate = 0.007 in/rev and the depth of cut for each pass = 0.100 in. The cost of the operator and machine = $39/hr and the tool cost = $2.00/cutting edge. The applicable Taylor tool life equation has parameters: n = 0.26 and…