1. Shaper (#*) Machine function and design requirements: The main function of this machine is to make surface more smooth; The required movements are: Reciprocating movement of planer knife and feed movement of the bow. It is required that the cutting speed is uniform, while the quirkily return is included. The basic data is: principal axis rotation speed is 60 r/min, the max length is less than 450 mm, the distance between working surface and the floor is 800 mm. Travel speed ratio coefficient is 1.5, allowable pressure angle 15°, cutting quantity is 0.1~0.5 mm. Requirements: 1. Freedom calculations; 2. Force analysis; 3. Make this machine, and display; please give a solution with given condition.

1. Shaper (#*) Machine function and design requirements: The main function of this machine is to make surface more smooth; The required movements are: Reciprocating movement of planer knife and feed movement of the bow. It is required that the cutting speed is uniform, while the quirkily return is included. The basic data is: principal axis rotation speed is 60 r/min, the max length is less than 450 mm, the distance between working surface and the floor is 800 mm. Travel speed ratio coefficient is 1.5, allowable pressure angle 15°, cutting quantity is 0.1~0.5 mm. Requirements: 1. Freedom calculations; 2. Force analysis; 3. Make this machine, and display; please give a solution with given condition.

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter1: Introduction To Machining

Section1.1: Introduction To Machining

Problem 9RQ: What machine tool is available with either horizontal or vertical spindle orientation and uses...

See similar textbooks

Similar questions

What is a benefit of using a DRO instead of micrometer collars for positioning on a vertical milling machine?
For pocket operation of 2 x 3 inch surface and dept of 0.06 in using 0.5 in end mill tool. What is the time required to finished a cut when the depth of cut is 0.3 inch and the feed rate 0.05 inch/rev, spindle RPM is 60. The subject is Machine Shop Theory. Please make clear the solution and answer and understandable. Thanks
For face milling a 2 x 3 inch surface using 1.5 in face mill tool. What is the time required to finished a cut when the depth of cut is 0.02 inch and the feed rate 0.05 inch/rev, RPM is 60. The subject is Machine Shop Theory. Please make clear the solution and answer and understandable. Thanks
Mention the difference between Shaper machine and planer machine?
In an orthogonal machining with a tool of gº orthogonal rake angle, the uncut chip thickness is 0.2 mm. The chip thickness fluctuates between 0.25 mm and 0 4 mm what is the ratio of the maximum shear angle to the minimum shear angle during machining?
Q1. A job of diameter 30 mm is being machined at feed of s = 1.0 mm/rev and spindle speed of n = 500 rpm, with a tool of orthogonal rake angle ? = 5° and primary cutting edge angle ? = 60°. Determine the height at which the tool tip should be set to achieve actual rake angle of 0°.
Q#2 “Milling is an intermitted cutting operation”. Explain it.
(a) Explain the difference between roughing and finishing operations in machining.(b) What are the parameters of a machining operation that are included within the scope of cuttingconditions?(c) What is the difference between threading and tapping?(d) A cylindrical workpiece is to be turned in a lathe. Determine the material removal rate if thecutting speed = 2.30 m/s, feed = 0.32 mm/rev, and depth of cut = 1.8 mm.(e) In a turning operation using high-speed steel tooling, the cutting speed = 110 m/min. The Taylortool life equation has parameters n = 0.140 and C = 150 (m/min) when the operation is conducteddry. When a coolant is used in the operation, the value of C is increased by 15%. Determine thepercent increase in tool life that will result if the cutting speed is maintained at 110 m/min.
ME-408 MACHINE SHOP THEORY AND PRACTICE Aside from the number of jaws, what is the difference between three-jaw and four-jaw chucks?
In an orthogonal cutting operation an 8 mm deep groove is to be turned on a 50 mm diameter steel bar. Spindle speed is 300 rpm and a feed rate of 0.25 mm/rev is given to the tool. Produced chips have a width of 2 mm. Calculate the material removal rate at the beginning and at the end of the cut. Can u help me please?
Q6) Explain the various milling cutters used in industry with their typical applications.
Assume that, in orthogonal cutting, the rake angle is 20 and the friction angle is 35 at thechip-tool interface. Determine the percentage change in chip thickness when the frictionangle is 50. Note that Merchant’s equation is more preferable.