400 mm 200 mm 1500 N 20 mm 1000 N

Q: Draw Mohr's circle for the state of stress defined by 01 = 80 MPa, o2 = -20 MPa and t12= 40 MPa. (1…

A: To draw mohr's circle for the state of stress

Q: Determine the stress components acting on the inclined plane AB. Solve the problem using the method…

A:

Q: Determine the state of stress at point A on the cross section of the pipe at section a–a. Show the…

A:

Q: Take the section AB, construct the FBD and label the internal loadings, determine the normal stress…

A:

Q: The steel pipe has an inner diameter of 2.75 in. and an outer diameter of 3 in. If it is fixed at C…

A: Since the magnitude of the direct shear stress compared to the twisting and bending stresses is very…

Q: Determine (a) the principal stresses and (b) the maximum in-plane shear stress and average normal…

A:

Q: The state of stress at a point is shown on the element. Determine (a) the principal stresses and (b)…

A: Part A) Write the equation of principal stresses. Substitute the required value in the equation(1)…

Q: Determine the state of stress at point A on the cross section of the pipe at section a–a. Show the…

A:

Q: Determine (a) the principal stresses and (b) the maximum in-plane shear stress and average normal…

A: (a) The principal stresses can be determined as,

Q: The square steel plate has a thickness of 10 mm and is subjected to the edge loading shown.…

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Q: The bar has a constant width of 35 mm and a thickness of 10 mm. Determine the maximum average normal…

A:

Q: Determine (a) the principal stresses and (b) the maximum in-plane shear stress and average normal…

A:

Q: Determine the stress components acting on the plane AB. Solve the problem using the method of…

A:

Q: The beveled gear is subjected to the loads shown. Determine the stress components acting on the…

A:

Q: The bolt is fixed to its support at C. If a force of 18 lb is applied to the wrench to tighten it,…

A: Given Data: The applied force is F = 18 lb. The length from force is l = 6 in. Diameter of shank is…

Q: Determine the maximum normal stress developed in the bar when it is subjected to a tension of P = 2…

A: Given:- P=2kip,Width of section of bar with hole,w1=1.875 inch,Width of section of bar without…

Q: Determine the equivalent state of stress on an element at the point which represents (a) the…

A: Given that, σx=50 MPaσy=0 MPaτ=15 MPa (a) Calculating principle stresses, Writing the formula for…

Q: Determine the average punching shear stress the circular shaft creates in the metal plate through…

A: Given data: The value of shear load is F=40 kN The diameter of shaft is dAB=50 mm The thickness of…

Q: Three forces of 500 lb, 800 lb, and 600 lb are applied to the end of the 2-in-diameter bar, as…

A:

Q: The solid rod is subjected to the loading shown. Determine the state of stress at point A, and show…

A: Given data: The force in x direction is Fx = 100 kN. The force in y direction is Fy = 10 kN. The…

Q: F1-11. Determine the average normal stress developed at points A, B, and C. The diameter of each…

A: When an external force is applied to any body the body gets deformed. This deformation is resisted…

Q: The pipe assembly is subjected to the loads shown. Determine the state of stress at point A on…

A: Given data, Let Ax, Ay and Az are the reaction force at A Bx and Bz are the reaction force at B Cz…

Q: The long bolt passes through the 30-mm-thick plate. If the force in the bolt shank is 10 kN,…

A:

Q: The bar has a diameter of 40 mm. Determine the state of stress at point A and show the results on a…

A: Section properties can be determined as

Q: The solid rod is subjected to the loading shown. Determine the state of stress at point B, and show…

A: Given data:

Q: Es atmospheric. Determine (a) the radial and tangential stress distribut across the the thickness,…

A: a = 8cm, b=12cm, Pb = -0.09MPa

Q: The rod has a diameter of 40 mm. If it is subjected to the force system shown, determine the stress…

A: Understand that the point A lies on the outer periphery of the shaft on the z axis. The Torsional…

Q: The long bolt passes through the 20-mm-thick plate. If the force in the bolt shank is 9 kN,…

A: Given data: ● The force applied on the bolt shank: F = 9 kN = 9000 N ● The thickness of the plate…

Q: Determine the state of stress at point A on the cross of the pipe at section a-a. Show the results…

A:

Q: Determine (a) the principal stresses and (b) the maximum in-plane shear stress and average normal…

A:

Q: F8-6. Determine the state of stress at point A on the cross section of the pipe assembly at section…

A: To find: The state of the stress at point A. Formula used: The shear stress τ is given by, τ=VQIb…

Q: Determine the shear stress at point A on the surface of the shaft. Represent the state of stress on…

A: Write the twisting moment at the cross section containing point A.

Q: F8-6. Determine the state of stress at point A on the cross section of the pipe assembly at section…

A:

Q: The beam has a rectangular cross section and is subjected to the loading shown. Determine the state…

A: The given beam is subjected to three loads- axial load, shear load and bending moment. Therefore…

Q: The rib-joint pliers are used to grip the smooth pipe C. If the force of 100 N is applied to the…

A: Given: The magnitude of the force applied on the handles is FH=100 N. The length and breadth of the…

Q: Determine the stresses at point A. The circular solid shaft has a radius of 40 mm. 300 тm 200 mm B.…

A: Given Data, F= Eccentric shear force = 30 KN r= Radius of the shaft = 40mm According to the diagram…

Q: F9-2. Determine the equivalent state of stress on an element at the same point oriented 45°…

A:

Q: Determine the maximum normal stress developed in the bar when it is subjected to a tension of P = 8…

A: Maximum normal stress at the fillet                    rh=1020=0.5wh=4020=2 For that stress…

Q: Determine (a) the principal stresses and (b) the maximum in-plane shear stress and average normal…

A: Given, σy=50 MPa,τxy=30 MPa

Q: The plate has a thickness of 20 mm and the force P = 3 kN acts along the centerline of this…

A: Given, thickness of the plate, t=20mm=0.02m Force on the plate, P=3kN We need to Plot the…

Q: The long bolt passes through the 30-mm-thick plate. If the force in the bolt shank is 8 kN,…

A:

Q: Determine (a) the principal stresses and (b) the maximum in-plane shear stress and average normal…

A: Given  The normal stress in x direction is σx=45 MPa. The normal stress in y direction  is σy=-60…

Q: Determine (a) the principal stresses and (b) the maximum in-plane shear stress and average normal…

A: σx=-30 ksi σy=0Txy=9ksi. To calculate the avg stress σavg=σx+σy2=-30+02=-15ksi Radius of the circle…

Q: The bent shaft is fixed in the wall at A. If a force F is applied at B, determine the stress…

A: ∑Fx=0;   Vx-13cos 45ο=0⇒Vx=9.19 lb∑Fy=0;   Ny-13 cos45ο=0⇒Ny=9.19 lb∑Mx=0;  Mx-13…

Q: The steel pipe has an inner diameter of 2.75 in. and an outer diameter of 3 in. The pipe is fixed at…

A:

Q: If the box wrench is subjected to the 50-lb force, determine the principal stresses and maximum…

A: Draw the section a-a with shear force and bending moments.     Apply force equilibrium in the…

Q: Determine the state of stress at point A on the cross section of the pipe assembly at section a-a.…

A:

Q: The drill is jammed in the wall and is subjected to the torque and force shown. Determine the state…

A: A drilling machine is used to drill in-wall or furniture. To analyze the drill bit stresses we first…

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.