4340 steel has been selected to create a high-strength turbopump shaft. The diameter of the shaft is 1.75in. Suggest an overall processing sequence which includes steps such as raw material procurement , heat treatment, rough machining, and finish machining. Specify the heat treatment state the steel should be procured in. Suggest a heat treatment procedure to achieve a very high strength and hardness around 50 HRC. Specify the relevant AMS specification. Be sure to supply temperatures, soak times and quenchants as applicable.

4340 steel has been selected to create a high-strength turbopump shaft. The diameter of the shaft is 1.75in. Suggest an overall processing sequence which includes steps such as raw material procurement , heat treatment, rough machining, and finish machining. Specify the heat treatment state the steel should be procured in. Suggest a heat treatment procedure to achieve a very high strength and hardness around 50 HRC. Specify the relevant AMS specification. Be sure to supply temperatures, soak times and quenchants as applicable.

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter2: Measurement, Materials, And Safety

Section2.7: Heat Treatment Of Metals

Problem 4RQ: What type of hardening operation that leaves the inner core in a softer condition is sometimes...

See similar textbooks

Similar questions

Please match Heat-Treated Steels with their hardness HB numbers, according to the charts shown below. a) SAE 1040 WQT at different Temperatures b) SAE 4140 OQT at different Temperatures c) SAE 4340 OQT at different Temperatures SAE 1040 WQT 1000 SAE 4140 OQT 1000 SAE 4140 OQT 1100 SAE 4340 OQT 800 a. HB = 415 b. HB = 341 c. HB = 311 d. HB = 269
State the range of carbon content in terms of weight percentage that can be theoretically varied in steel. Upon increasing the carbon content in plain carbon steel within the theoretical range, will it enhance or retard the mechanical properties such as tensile strength, compressive strength and hardness.? Give your answer with the span of carbon content that the particular property can. It can prevail.
An application requires ultimate tensile strength and yield strength ofa steel at 110 ksi and 91 ksi, respectively. Answer the following 4 questions: Can SAE 1040 steel be selected for this application? If “no” is the answer in Part I, the following Part II, III, and IV can beignored. If “yes” is the answer in Part I, which condition of SAE 1040 shouldbe selected? Why is that steel with the condition in part II selected? Is the selected steel brittle or ductile? and Why?
With respect to the S-N diagram shown below, answer the following questions:(a) for Gray cast iron, what is the projected number of cycles to failure for an induced stress of 20,000 psi?(b) What is the endurance limit and associated stress for a 0.47% heat treated carbon steel? (c) What is the endurance limit for the Aluminum-copper alloy?(d) What is the endurance strength for heat treated Alloy Steel at 400,000 cycles?
Explain the connection between notch strengthening and material ductility; which is more likely to notch strengthen––pure Al or martensitic steel?
2. Which property of this steel is significant to the failure analysis? The steel can Options: a. form carbides that strength it b. be heat treated in order to improve its strength. c. be strain-hardened.
The annealed low carbon steel behavior is approximated by σ = 10000ε 0.25 MPa. Evaluate (a) The yield strength after the bar is cold worked for __%. (b) If the same annealed low carbon steel bar is initially cold worked __%, followed by additional cold work of __%, determine the probable yield strength of the final bar. (c If the same annealed low carbon steel bar was cold worked for an unknown amount and then cold worked 20% more and found to have a yield strength of __ MPa. What was the unknown amount of cold work. (d) Discuss the variation of yield stress in question a & b. (e) Discuss the effect of mechanical working on variation of properties with respect to grain size. Also draw a clear graph of properties versus grain size for ductility and strength. σ = 10000ε 0.24 (a) 30% (b) initially 15% followed by 20% (c) yield strength of 7500 MPa
Determine the yield strength sy and the ultimate strength su of the A36 steel either from Materials Science class book/notes, or by researching over the internet.
Show microstructure of 8620 steel before homogenized annealing and microstructure after annealing.
Project 2:Table 3 shows the fatigue data for a ductile cast iron to be used for an automobile axle that rotatesat an average rotational speed of 750 revolutions per minute:a) Make an S-N plot (stress amplitude versus logarithm cycles to failure).b) What is the fatigue limit for this alloy?c) Determine the fatigue lifetimes at stress amplitudes of 500 MPa and 400 MPa?d) Estimate the maximum lifetime of continuous driving that are allowable for the following 250MPa and 150 MPa stress levels.
A steel is to be selected from Appendix C-4a. Estimate Su and Sy from the given values of Brinell hardness for the selected steel.
Q15. Materials 605M36 and 655M31 have the same yield and ultimate tensile strengths and the same percentage elongation, yet they are not the same steels. What are their carbon equivalents? 605M36 655M31