A summing amplifier is shown.a. If v₁ = 1 V, v₂ = −1 V, and vc=-1 V,find vo.+44 ΚΩwwwb. Find v, if the current through the 3.3 k load resistor is io=27.5 ΚΩwww+Vc80 ΚΩw2 mA.110 ΚΩww10 V-10 VCopyright ©2015 Pearson Education, All Rights Reserved+ioυ Σ3.3 ΚΩ

Answered: Image /qna-images/answer/6218fc67-c113-43d4-ace0-296d310ec42c.jpg

+ 44 ΚΩ υ 27.5 ΚΩ ww Vc 80 ΚΩ ww A summing amplifier is shown. a. If va = 1 V,vb = −1 V, and v = −1 V, find vo. b. Find v. if the current through the 3.3 kΩ load resistor is io = 2 mA. ΠΟΚΩ www ●+ >10 V –10V συχνά με τους Μακαμπάκας, κι έγινε μόνος + 0 §3.3 kΩ

+ 44 ΚΩ υ 27.5 ΚΩ ww Vc 80 ΚΩ ww A summing amplifier is shown. a. If va = 1 V,vb = −1 V, and v = −1 V, find vo. b. Find v. if the current through the 3.3 kΩ load resistor is io = 2 mA. ΠΟΚΩ www ●+ >10 V –10V συχνά με τους Μακαμπάκας, κι έγινε μόνος + 0 §3.3 kΩ

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the circuit shown in figure. The value of Vc is .............. Volt. . * 21.24 29.24 24.27 25.24 27.24 23.25 The value of VB is .............. Volt. . * 3.58 5.58 4.58 1.58 8.58 2.58 The value of RE is .............. Kohm. . * 1 2 1.9 2.1 1.6 1.4 The value of Beta is .............. . . * 57.39 51.39 53.93 55.93 56.39 54.93
Find Vc and Vd. Show complete solution.
(a) Find the The´venin equivalent representation of the circuit shown in (a) ifβ =120, R1 =56kΩ, and R2 =75 kΩ. (b) Repeat forcircuit shown (b).
For the circuit shown in 2.24, R1=40 kΩ R2=60 kΩ, RC=750 Ω, RE=120 Ω, VCC=10 V, V0=600 mV, and β=49.Calculate iB, iC, iE, v3d, vbd, i2, i1, vab, iCC, and v13 . (Note: In thedouble subscript notation on voltage variables, the first subscript ispositive with respect to the second subscript. See P2.39.)
An amplifier drives an external load having impedance (8 + 4j)ohm. What is the output impedance of the amplifer (i.e., Thevenin equivalent impedance) that allows maximum power generation in the load?
FIND GAIN Av( NEED NEAT HANDWRITTEN SOLUTION ONLY OTHERWISE DOWNVOTE).
(a) Draw the AC equivalent circuit for the circuit given in Fig. 4.(b) Calculate the overall/total voltage gain AVTL and output voltage V0 for the circuit in Fig. 4. You are required to show all necessary steps for your calculations.
Suppose L =10 henrys, R= 10 ohms, C= 1/500 farads,E= 100 volts, q(0) = 10 coulombs, and q'(0) = i(0) = 0 . Formulateand solve an initial value problem that models the givenLRC circuit. Interpret your results
MechatronixOne is a manufacturer of an industrial and toy robots. They are in the planning stage to develop a prototype AI robot for industry that will be supplied by a 12V DC with Izm = 20mA. This AI robot as they envision has a capability to understand litthe English command. Their problem is how to design an RC filtered power supply that can be used in their prototype AI robot which has a load range of 250 ohms to 1.25 kilo-ohms and since this is just a prototype it must be wired to the 240V 60Hz peak AC supply in their laboratory. They ask the VoltageMaker Company to ship them 20 pcs of 12V DC power supply and it must be included in the data sheet of load current in rms and peak, the PIV, the power range absorbed by the load, the ratio of the transformer, and the secondary rms voltage of the power supply. The power supply must be in a bridge type. Considering that you are a member of that team, what is your design? please answer or draw it clearly with labels. Thank you. this…
Design a combinational circuit with three inputs (E,L,Y) and three outputs (F,R,A). If the input is less than 5, then the output is 2 greater than the input. Otherwise, the output is 3 less than the input. if E=0 L=0 and Y=0, then if E=0 L=0 and Y=1, then if E=0 L=1 and Y=0, then if E=0 L=1 and Y=1, then…
Consider the circuit depicted in Figure. If vs(t) =−8 + 2u(t) V, determine Vc(0+)
) Below, the circuit given in Figure 1 will be analyzed in the s definition region.a) Obtain node equations and additional equations for the specified nodes.b) VRy (t) for R1 = 1Ω, RY = 1Ω, e (t) = βu (t), C = 2F, L = 1H, vc (0) = 1V, iL (0) = 2ACalculate the voltage.β=8,a=3