In the circuit of the figure below, assume that Rs = R₁ = 20092, Rt = 50 k2, and vs = 400 sin cot V. The diode is ideal, with reverse saturation current Io = 2 μ A and a peak inverse voltage (PIV) rating of V₁ = 100 V. (a) Will the diode fail in avalanche breakdown? (b) If the diode will fail, is there a value of RL for which failure will not occur? VS Rs R₁ ww ip + UD D RL VL

In the circuit of the figure below, assume that Rs = R₁ = 20092, Rt = 50 k2, and vs = 400 sin cot V. The diode is ideal, with reverse saturation current Io = 2 μ A and a peak inverse voltage (PIV) rating of V₁ = 100 V. (a) Will the diode fail in avalanche breakdown? (b) If the diode will fail, is there a value of RL for which failure will not occur? VS Rs R₁ ww ip + UD D RL VL

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
What is CEMF?
What is the difference between a diode and rectifier?
4670V = VsR = 200kΩ C = 0.1μF Consider the circuit and parameters illustrated above. If a derating factor of 12% is sugested then calculate, 12) the maximum reverse voltage rating of the diodes; 13) the string efficiency of this arrangement; 14) the maximum difference in leakage current of the diodes; 15) the maximum difference in stored charge of the diodes.
The diode current in a p-n junction is modeled exponentially (given below.) When the p-n junction is polarized with 0.7V and 0.75V, the currents flowing through the diode are again measured on the basis of 1.36 mA and 7.20 mA. Accordingly, what is the ideality factor? (Note: Take the thermal voltage as mV)
For the half-wave rectifier circuit shown, the diode is not ideal and is modeled as an ideal voltage source of value Vf= =0.65V in series with an ideal diode. Vin= 2sin(2π10t) and R= 470Ω. What is the magnitude of the diode current at time t=60mst=60ms? 2- At what time between 0and T/4 seconds is the magnitude of the diode current equal to 2.66mA? Tis the period of Vin Enter your answer in milliseconds
Which of the following indicates the correct rms value of the diode current for a 1-0 full bridge diode rectifier supplied by a source voltage of 220 V, 60 Hz? The value of load resistance is 2012 (assuming large inductance for maintain constant load current). (a) 9.90 A (b) 7.0 A (C) 4.95 A (d) 11 A COMPANY
Zener voltage, VZ = 6.1V and incremental resistance, rz = 0 a) Determine the value of Ri such that the Zener diode remains in breakdown if the load current varies from IL = 20 to 200 mA and if the input voltage varies from VI = 8.6 to 10V. Assume IZ(min) = 0.1IZ(max). b) Determine the power rating required for the Zener diode and the load resistor. c) If the position of Zener diode were changed to be in forward bias region, will the voltage regulator still work properly? Justify your answer
We wish to design a Si p+-n diode such that the avalanche breakdown and punchtrough at 300 K both occur at 15 V. Assume the relative dielectric constant of the semiconductor is 10, V0 is 0.5 and the breakdown field is 1 MV/cm. Determine the width and doping of the n-region.
Calculate the total current of a circuit with a 9.5 V voltage source connected in series with a directly biased silicon diode and a series resistor of 440 Ω. Consider the second approximation of the diode where it is considered to be connected to a battery in series. Units of the response in milli amperes. Note: I put the original exercise in Spanish, so that it is better understood. Explain step by step, please.
2b) A regulator curcuit needs to be designed with an input power supply which has a nominal value of V_PS=20 V and can vary by ± %25 and nominal output voltage of 10 volts. For this purpose a zener diode is employed with specifications given; power rating of 1 W, 10V drop at Iz=25 mA, output load current is to vary between I(subscript L)=0-20 mA and zener resistance of r_Z=5Ω i) If the minimum Zener current is to be I_Z=5 mA, determine the required R_S ii) Determine the maximum variation in output voltage iii) Determine the regulation percent
DiodesFill in the blanks with the words belowcheck valve, conductance, convert, crystalline, impurities, infinite, galena, p–n junction, rectifying,resistance, selenium, semiconductor, switching circuits, tailored, temperature, threshold, two-terminal,unidirectionalA diode is a 1 ………………… electronic component that conducts current primarily in one direction(asymmetric 2 ………………..); it has low (ideally zero) 3 ……………… in one direction, and high (ideally4 ………………..) resistance in the other. A 5 ………….. diode, the most common type today, is a 6……….. piece of semiconductor material with a 7 ………………. connected to two electrical terminals. Avacuum tube diode has two electrodes, a plate (anode) and a heated cathode. Semiconductor diodes were thefirst semiconductor electronic devices. The discovery of crystals' 8 ……………… abilities was made byGerman physicist Ferdinand Braun in 1874. The first semiconductor diodes, developed around 1906, weremade of mineral crystals such as 9 ……………….. . Today,…