7 5-15. Determine the reaction atfixed support A.Problem 5-153 kN0.5 kN/m5 kN- m6 m3 mThe left end of the beam is fixed to a wallat point "A". A force arrow labeled 3 k Npoints vertically downward to the rightend of the beam. A uniformly distributedand then uniformly decreasing load ofmaximum magnitude 0.5 k N divided bym is acting on the beam from the leftend. The uniformly distributed load isacting till a distance of 6 m from point"A". A clockwise moment arrow labeled 5kN m is acting at the right end of thebeam.

For the given beam To determine Reactions at A

Answered: 5-15. Determine the reaction at fixed…

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.4.14P

See similar textbooks

Similar questions

An aluminum box column with a square cross section is fixed at the base and free at the top (sec figure). The outside dimension b of each side is 100 mm and the thickness t of the wall is 8 mm. The resultant of the compressive loads acting on the top of the column is a force P = 50 kN acting at the outer edge of the column at the midpoint of one side. What is the longest permissible length Lmaxof the column if the deflection at the top is not to exceed 30 mm? (Assume E = 73 GPa
The fr a me A BCD shown in the heure is squeezed by two collinear forces P acting at points A and D. What is the decrease ê in the distance between points A and D when the loads P are applied? (The flexural rigidity EI is constant throughout the frame,) Note: Disregard the effects of axial deformations and consider only the effects of bending due to the loads P.
The aluminum pipe shown in Fig. is used to support a load of 150 kip.Determine the maximum displacement at the top of the pipe if the load is(a) applied gradually, and (b) applied by suddenly releasing it from the topof the pipe when h = 0. Take Eal = 10(103) ksi and assume that thealuminum behaves elastically.
The assembly below consists of a steel rod CB and an aluminium rod BA, each having a diameter of 12 mm. If the rod is subjected to the axial loadings at A and at the coupling B, determine the displacement of the coupling B and the end A. The unstretched length of each segment is shown below. Neglect the size of the connections at B and C, and assume that they are rigid. Est = 200 GPa, Eal = 70 GPa.
The flywheel causes a completely reverse bending on the shaft and the factor of safety is 2, determine: a. The ultimate tensile strength (Su) of the material if the Yield strength (Sy) is 0.6 of Ultimate strength. b. The fatigue life of the shaft given the fatigue strength (Sf) is equal to 0.8 Su and endurance Strength (Se) is equal to 0,5 Su, given the minimum stress is 0.3 of Maximum stress c. Draw the S-N diagram
A circular steel rod has a diameter of 50 mm. It touches the unyielding supports at point A and B when ?1 = 80 °C. Find the applied force P to the collar at its midsection so that, when ?2 =30 °C, the reaction at B is zero. Use E st = 200 GPa and the coefficient of linear expansion of steel is at 12 x 10^-6 m/m C.
The system is made up of a bar, supported by a pin at point A and by a smooth collar at point B (the collar slides on the ABG bar). The collar is pinned to bar BDE, and bar BDE is supported by a pin at D and a cable at end E. Determine the innner charges un a cut that passes trough the point G(normal force and cutting force, and flexing moment With T=26 lb, a=4 in, b=9 in
The assembly consists of two rigid bars that are originally horizontal. They are supported by pins and 0.25-in.-diameter A-36 steel rods. If the vertical load of 5 kip is applied to the bottom bar AB, determine the displacement at C, B, and E.
Find the Controlling buckling load (kips) for the steel column shown in the figure. The column is Fixed at the base and free at the top and is made up of two C6 x 10.5 shapes that act together. Assume that E = 30,000 ksi and L = 14 ft.
Before the load is placed on the rigid plate, the top of the central spring is 20 mm lower than the outer springs. Each outer spring is made of 24 turns of 15-mm diameter wire on a mean radius of 60 mm. The central spring consists of 16 turns of 20 mm dimeter wire on a mean radius of 80 mm. If a load P = 5 kN is now placed on the rigid plate. Disregarding the weight of the plate, use G = 83 GPa and use Light spring formula. Determine the maximum shearing stress of the in uter spring. In MPa
A 20-ft-long column is made of aluminum alloy 2014-T6. If it is pinned at its top and bottom, and a compressive load P is applied at point A, determine the maximum allowable magnitude of P using the equations of Sec. 13.6 and the interaction formula with (sb)allow = 20 ksi.
The post is made from 606l-T6 aluminum and has a diameter of 50 mm. It is fixed supported at A and B, and at its center C there is a coiled spring attached to the rigid collar. If the spring is originally uncompressed, determine the compression in the spring when the load of P = 50 kN is applied to the collar.

SEE MORE QUESTIONS

Recommended textbooks for you

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS